Renesas Electronics

ISL8483EIB - 5V RS-485/RS-422 Transceiver | Renesas Electronics

MPN: ISL8483EIB ✓ פעיל
5 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC Package
כמות הזמנה מינימלית: 1 |

ISL8483EIB סקירה

Renesas Electronics ISL8483EIB is a single RS-485/RS-422 transceiver operating from a 5 V supply, with integrated protection for driver outputs and receiver inputs against electrostatic-discharge strikes up to ±15 kV. The device is packaged in an 8-pin SOIC and supports balanced differential communications over industrial, instrumentation, automation, and point-to-point data links.

A transceiver combines a differential line driver and receiver in one integrated circuit, allowing a printed circuit board to transmit and receive on the same balanced bus wiring. Within the interface-IC hierarchy, the ISL8483EIB belongs to the RS-485/RS-422 interface family, combines data communication with ESD protection, and is used where noise immunity, ground-offset tolerance, and common-mode rejection improve reliability over single-ended signaling.

The manufacturer identifies the ISL8483E family as ESD-protected, low-power BiCMOS transceivers for 5 V operation. The ISL8483EIB provides one driver and one receiver in an 8-SOIC package. Its ±15 kV ESD protection is a principal feature for exposed communications equipment, while short-circuit current limiting and on-chip thermal shutdown help the driver withstand bus contention. These protections address field-level faults encountered in industrial wiring.

BiCMOS construction combines bipolar and CMOS characteristics, supporting low-power operation and high-speed balanced signaling. The RS-422 mode supports point-to-point and multidrop communication, while RS-485 permits multiple drivers on a shared bus when the system designer controls inactive states, termination, and biasing correctly. The exact propagation-delay, slew-rate, data-rate, output-current, and temperature limits should be selected from the manufacturer datasheet for the intended system conditions.

Typical uses include industrial sensor gateways, motor-control diagnostics, factory equipment interfaces, building automation, instrumentation links, and embedded serial buses. In each case, the transceiver converts logic-level serial information into balanced differential signals and returns differential bus data to receiver logic, reducing susceptibility to electromagnetic noise over longer interconnects.

Designers should use a common ground reference between the transceiver and system electronics, place termination at the physical ends of the bus, and provide a bias network only when the installed network requires it. Protection components and chassis-ground design must be evaluated against the actual cable environment. Input and output filtering should be tested for signal-integrity margin before production release.

This product page combines manufacturer specifications, source-linked availability information, interface use cases, and practical PCB-design considerations to support component selection and replacement planning. The ISL8483EIB is especially relevant when an existing 8-SOIC RS-485 or RS-422 design requires 5 V operation and ±15 kV ESD-protected driver or receiver nodes.

חלופות תחליף ישיר עבור ISL8483EIB — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם ISL8483EIB (אותו גורם צורה וטביעת רגל) — שונים ב ESD Protection, Mounting Type, Package.

Renesas Electronics
ESD Protection: ±15 kV
Mounting Type: Through-hole
Package: 8-pin PDIP
השווה עם ISL8483EIB →

ISL8483EIP

✅ Drop-In
Renesas Electronics
📦 SOIC-8
Single RS-485/RS-422 transceiver · 1 transmitter and 1 receiver · 5 V · ±15 kV · RS-485 and RS-422 · BiCMOS · On-chip short-circuit current limiting · On-chip thermal shutdown

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

ISL8483EIBZ

✅ Drop-In
📦 SOIC-8
Same-family 8-SOIC ordering option; 0% difference identified in the cited 5 V RS-485/RS-422 and ±15 kV ESD ratings, while suffix-specific order information requires confirmation

📋 חלופה להתייחסות (לא בקטלוג)

ISL8483EIB מפרטים

Product Type Single RS-485/RS-422 transceiver
Number of Drivers 1 driver
Number of Receivers 1 receiver
מתח אספקה 5 V
Interface Standards RS-485 and RS-422
ESD Protection ±15 kV on driver outputs and receiver inputs
Technology BiCMOS
Driver Short-Circuit Protection On-chip short-circuit current limiting
Thermal Protection On-chip thermal shutdown
מארז 8-pin SOIC
סוג הרכבה Surface mount
Signal Type Balanced differential

מדריך תצורת פינים של ISL8483EIB 8-pin soic

תצורת פינים עבור ISL8483EIB (מארזת 8-pin soic). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.

תרשים פינים של מארזת 8-pin soic עבור ISL8483EIB

אין נתוני פריסת פינים מפורטים עבור ISL8483EIB.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

ISL8483EIB מתאים עבור 6 יישוםs: Industrial Sensor Gateways, Building Automation Networks, Motor Control Diagnostics, Instrumentation and Test Equipment, Point-to-Point Data Links, Embedded Communication Modules.

🏭

Industrial Sensor Gateways

The ISL8483EIB fits industrial sensor gateways that must communicate over long, potentially noisy factory cables. Its 5 V supply, balanced RS-485/RS-422 signaling, and ±15 kV ESD protection on driver outputs and receiver inputs help preserve data integrity where cables pass near motors and switching equipment. The transceiver provides one driver and one receiver per device, so gateways can use one channel for transmission and another for reception. Designers should maintain a common ground, terminate the bus at its physical ends, and verify timing against the maximum bus length and data rate.

🏭

Building Automation Networks

The ISL8483EIB can serve as a node interface in building-automation equipment that links sensors, controllers, and actuators over balanced wiring. RS-485 is useful for multidrop installations, while the receiver benefits from differential signaling in environments containing lighting and motor-control equipment. The documented ±15 kV interface protection improves resilience against electrostatic discharge at externally accessible connections. Installation practice remains important: use a controlled ground reference, avoid long unshielded stubs, and confirm whether the network requires termination or biasing.

🏭

Motor Control Diagnostics

The ISL8483EIB is appropriate for isolated or remotely located motor-control diagnostics where command, status, and fault information must cross a noisy power environment. Its differential RS-422 or RS-485 interface reduces susceptibility to ground-potential and common-mode noise, while current limiting and thermal shutdown help the driver survive contention. The 8-SOIC package supports compact controller boards, but the designer must calculate driver dissipation under sustained load, preserve adequate copper area, and validate the interface against the motor system's EMC and surge requirements.

🔧

Instrumentation and Test Equipment

The ISL8483EIB works well as the balanced communication element in instrumentation and test equipment that must exchange commands and measurement data across bench or system-level cables. The 5 V operating supply integrates easily with mixed-signal test hardware, and the ±15 kV protected driver and receiver nodes improve reliability when users connect external equipment. For laboratory systems, engineers should still evaluate cable length, grounding, connector discharge paths, and the exact propagation-delay limits in the manufacturer timing table.

🌐

Point-to-Point Data Links

The ISL8483EIB is suitable for point-to-point RS-422 links between equipment cabinets, remote modules, or embedded controllers. Balanced signaling and the ±15 kV ESD capability make the interface more resistant to noise and electrostatic discharge than a single-ended connection. A single device combines one driver with one receiver, allowing bidirectional communication when the enable controls are managed correctly. Layout should keep the differential route continuous, use a reference plane beneath it, and provide termination only as required by the cable and topology.

🧩

Embedded Communication Modules

The ISL8483EIB can add a robust differential port to embedded controllers, data-acquisition modules, and remote monitoring devices. Its 8-SOIC footprint simplifies PCB routing, and the 5 V supply is compatible with systems that already regulate 5 V for communications. ESD protection is particularly useful when the port reaches a connector or removable cable. Engineers should budget input and output filtering, check enable-polarity requirements in the firmware, and verify that the selected order code satisfies the product's operating-temperature envelope.

What is the ISL8483EIB?
The ISL8483EIB is a 5 V, single-channel RS-485/RS-422 balanced-line transceiver in an 8-pin SOIC package. According to the Renesas Electronics ISL8483E and ISL8485E datasheet, the family combines one driver and one receiver, uses BiCMOS circuitry, and provides ESD protection up to ±15 kV on driver outputs and receiver inputs. It is intended for industrial, instrumentation, and other noise-prone differential data links.
What are the key specifications of ISL8483EIB that engineers should know?
The ISL8483EIB is a 5 V RS-485/RS-422 transceiver with one driver, one receiver, ±15 kV ESD protection, and an 8-SOIC package. The Renesas Electronics datasheet also identifies short-circuit current limiting and on-chip thermal shutdown as protection features. Maximum signaling speed, propagation delay, quiescent current, and junction-temperature limits are not stated in the cited product results and must be confirmed from the manufacturer datasheet before timing or thermal design.
Where can I download the ISL8483EIB datasheet PDF?
The official ISL8483E and ISL8485E datasheet is available from the Renesas Electronics document page linked on this product page. The manufacturer describes the devices as ESD-protected, 5 V, low-power RS-485/RS-422 transceivers and explains that driver current limiting and thermal shutdown improve robustness during bus contention. Use the manufacturer PDF for the authoritative pin description, electrical characteristics, timing diagram, and application guidance.
Where can I find the ISL8483EIB pinout?
The ISL8483EIB pinout is shown in the pin-description section of the Renesas Electronics ISL8483E and ISL8485E datasheet. The device uses an 8-pin SOIC package and is a single RS-485/RS-422 transceiver. Use the manufacturer drawing when assigning pins because the package drawing is the authoritative source for signal names, enable-control behavior, supply pins, and any exposed or no-connect positions.
Is the ISL8483EIB suitable for industrial communication systems?
The ISL8483EIB is suitable for industrial balanced-data links because it supports RS-485 and RS-422, operates from a 5 V supply, and protects exposed driver and receiver nodes against ±15 kV ESD strikes. According to the Renesas Electronics datasheet, current limiting and thermal shutdown also help withstand bus contention. A production design must still validate the complete cable, grounding, surge, and electromagnetic-compatibility environment.
What is the difference between RS-485 and RS-422 operation with ISL8483EIB?
Both modes use the ISL8483EIB for balanced differential signaling, but RS-422 is primarily intended for point-to-point links, while RS-485 supports multipoint buses with multiple driver nodes. The Renesas Electronics datasheet states that the device meets both standards. For RS-485 networks, the designer must control driver enable states, apply termination at bus ends, and determine whether biasing is required to maintain a valid idle state.
How much ESD protection does the ISL8483EIB provide?
The ISL8483EIB provides ESD protection up to ±15 kV on each driver output and receiver input. The Renesas Electronics ISL8483E and ISL8485E datasheet describes the devices as ±15 kV ESD-protected and notes that the protection is designed to withstand strikes without latch-up. ESD rating is not the same as full surge immunity, so additional system-level protection may still be required.
Can ISL8483EIB operate in both RS-485 and RS-422 networks?
Yes, the ISL8483EIB supports both RS-485 and RS-422 differential communication. The manufacturer datasheet identifies the family as a transceiver for these standards. The interface configuration still depends on correct external wiring, enable control, termination, grounding, and—when used on a multi-driver RS-485 bus—logic that prevents multiple drivers from transmitting simultaneously.
What is the best drop-in replacement for ISL8483EIB?
The closest documented same-family replacement candidate is ISL8483EIP, while ISL8483EIBZ is another 8-SOIC ordering option with closely related ordering codes. However, the available cross-reference information does not establish five independently qualified drop-in products with fully verified electrical equivalence. Review the Renesas ISL8483E and ISL8485E datasheet for ordering-code, temperature-grade, package, and marking differences before replacing a populated assembly.
Can ISL8483EIBZ replace ISL8483EIB?
ISL8483EIBZ is a closely related 8-SOIC ordering option and appears in the available comparison data, but the available material does not provide a complete pin-by-pin and temperature-grade equivalence table. Confirm the order codes, package dimensions, device markings, and electrical limits in the manufacturer datasheet before treating it as a production drop-in replacement.
When should I choose ISL8483EIB over another RS-485 transceiver?
Choose the ISL8483EIB when a design specifically requires the Renesas ISL8483E family function, 5 V operation, 8-SOIC footprint, RS-485/RS-422 compatibility, and ±15 kV protected interface nodes. The Renesas Electronics datasheet also provides driver current limiting and thermal shutdown. A different transceiver may be preferable when its data rate, supply range, logic levels, package, or automotive qualification better matches the application.
ISL8483EIB versus ISL8483EIP — which is the better replacement?
ISL8483EIP is the closest same-family replacement candidate for ISL8483EIB because it appears in cross-reference material for the ISL8483EIP order code. The available results do not expose a complete parameter table for the temperature-grade and ordering differences, so the choice cannot be reduced to an unconditional drop-in claim. Compare the exact manufacturer ordering information and electrical table before approving a substitution.
What can replace ISL8483EIB in an 8-SOIC PCB design?
An ISL8483EIB replacement must match the 8-SOIC footprint, RS-485/RS-422 function, 5 V supply arrangement, and every connected logic or control pin. ISL8483EIP and ISL8483EIBZ are documented same-family candidates, but the available cross-reference results do not prove unqualified equivalence for every order code. Use the Renesas ordering table and pin description, then verify timing, ESD level, enable logic, and temperature limits.
Is ISL8483EIB in stock, and how do I request a quote?
Current inventory and a guaranteed lead time should be confirmed through the Request a Quote form on this page. Some source listings describe stock or immediate shipment, but listing-level availability can change and does not establish a durable stock commitment. The form is the appropriate route for current quantity, lead time, lot traceability, and shipment requirements for the exact ISL8483EIB order code.
What is the price of ISL8483EIB?
The current unit price for an exact ISL8483EIB order code should be requested through the Request a Quote form on this page. The available product results do not print an explicit quantity-break table for this exact MPN, so a current multi-tier price cannot be reproduced reliably. Quote requests should specify the required quantity, package quantity, and any date-code or traceability requirements.
What is the lead time for ISL8483EIB?
A current production lead time for ISL8483EIB should be confirmed through the Request a Quote form on this page. The verified listings show product availability information but do not state a guaranteed lead time for the exact target order code. Include your required delivery date and annual usage in the request so scheduling can be based on the requested quantity rather than generic listing availability.

נתוני עזר הנדסיים עבור ISL8483EIB — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the ISL8483EIB when the design requires the Renesas ISL8483E 5 V transceiver family, an 8-SOIC footprint, RS-485 and RS-422 support, and ±15 kV ESD protection on exposed communication nodes. It is especially useful in industrial equipment, motor-control diagnostics, instrumentation, and point-to-point links where differential signaling is preferred. ISL8483EIP is the closest documented same-family candidate and should be considered when its ordering or temperature-grade characteristics better match the production design. ISL8483EIBZ is another related 8-SOIC option, but the suffix-specific differences should be checked in the Renesas ordering information. No unrelated cross-brand device should be treated as a drop-in replacement unless its pinout, enable logic, 5 V electrical limits, timing, ESD rating, and temperature range have all been verified. Because the available cross-reference results do not establish five distinct, qualified drop-in products, this page lists only the two same-family candidates supported by the cited material.

השוואה עם חלופות

פרמטר מוצר זה ISL8483EIP ISL8483EIBZ
Package SOIC-8 SOIC-8 SOIC-8
Brand Renesas Electronics Renesas Electronics Renesas Electronics
Device Type Single RS-485/RS-422 transceiver Single RS-485/RS-422 transceiver Single RS-485/RS-422 transceiver
Supply Voltage 5 V 5 V 5 V
Driver and Receiver Count 1 driver and 1 receiver 1 driver and 1 receiver 1 driver and 1 receiver
ESD Protection ±15 kV ±15 kV ±15 kV
Technology BiCMOS BiCMOS BiCMOS
Short-Circuit Protection On-chip driver current limiting On-chip driver current limiting On-chip driver current limiting
Thermal Shutdown Yes Yes Yes

מבדילים עיקריים

  • High-voltage ESD protection on exposed interface nodes (לעומתISL8483EIP)
  • Integrated fault handling for bus contention (לעומתISL8483EIBZ)
  • Compact multi-standard interface (לעומתISL8483EIP)

הערות תכנון

Route the RS-485 or RS-422 differential pair as a tightly coupled pair with a continuous ground reference beneath it. Place transceiver, protection components, termination, and optional bias components close to the connector so transient energy is diverted before entering the logic section. Avoid stubs from the main bus and keep the differential trace away from switching nodes and high-current motor paths.

Decouple the 5 V transceiver supply locally with the capacitance and placement specified by the manufacturer datasheet. Keep the supply return path independent of noisy digital currents and verify the voltage at the device under maximum line loading. The driver’s short-circuit current limit and thermal shutdown improve fault tolerance, but they do not remove the need for correct supply regulation and layout.

Separate driver outputs from receiver inputs and avoid introducing unequal trace lengths within the differential pair. If the connector is exposed to user contact or long external cables, combine the interface’s ±15 kV ESD protection with a suitable external surge and connector strategy. Confirm that the protection-device capacitance does not distort the required edge rate or propagation delay.

Do not enable multiple RS-485 drivers on the same bus simultaneously, because simultaneous outputs can contend even though the device includes current limiting and thermal shutdown. On multidrop networks, terminate only the two physical ends and determine whether bias resistors are needed for a valid idle state. Also verify enable polarity, receiver-output behavior during shutdown, and ground-reference requirements in the manufacturer application information.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status is stated in the cited product results. AEC-Q100 is not applicable because this is an industrial interface IC rather than an automotive-qualified product.

חיפושים קשורים

ISL8483EIB datasheet ISL8483EIB datasheet pdf ISL8483EIB pinout ISL8483EIB schematic ISL8483EIB equivalent ISL8483EIB replacement ISL8483EIB cross reference ISL8483EIB vs ISL8483EIP ISL8483EIB footprint Renesas ISL8483EIB ISL8483EIB price ISL8483EIB stock ISL8483EIB RS-485 transceiver ISL8483EIB industrial application

רכיבים ומונחים קשורים

Renesas Electronics ISL8483EIB ISL8483EIP ISL8483EIBZ RS-485 RS-422 transceiver differential line transceiver interface IC BiCMOS ESD protection 5 V power supply driver receiver SOIC-8 surface-mount package industrial communication building automation motor control diagnostics instrumentation point-to-point data link short-circuit current limiting thermal shutdown common-mode rejection
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר