Texas Instruments

LM27965SQ-M - Dual White LED Driver | Texas Instruments

MPN: LM27965SQ-M ✓ פעיל
2.7 V to 5.5 V Vdss 180 mA Id 24-pin WQFN (RTW) Package 1.27 MHz Speed
כמות הזמנה מינימלית: 1 |

LM27965SQ-M סקירה

The Texas Instruments LM27965SQ-M is a charge-pump-based dual-display white LED driver with nine constant-current outputs, I2C-compatible brightness control, and support for up to 180 mA total LED current in a 24-pin WQFN (RTW) package measuring 4 mm × 4 mm × 0.8 mm.

A charge-pump LED driver is a power-management IC that uses switched-capacitor voltage conversion rather than an inductor to generate the controlled voltage needed by LEDs. The LM27965 belongs to the LED driver hierarchy, where switched-capacitor regulation combines with constant-current sinking, PWM dimming, and serial control to illuminate LCD backlights or other white-LED arrays.

The device can drive up to nine LEDs, with individual drive current programmable by external resistors up to 30 mA per LED. Its three independently controlled output groups support primary, secondary, and auxiliary backlight channels. A primary group can be configured for four or five LEDs, while the second group can be configured for four LEDs. The manufacturer specifies 0.3% current matching and peak LED-drive efficiency of 91%.

The LM27965 uses an adaptive 1× to 3/2× charge-pump topology, eliminating the need for an inductor. Its operating input range is 2.7 V to 5.5 V, supporting extended Li-ion operating conditions. The switching frequency is 1.27 MHz, and an external chip-reset pin provides a dedicated reset control for system integration.

Two I2C-compatible chip addresses are offered within the LM27965 family. Address 0x38 identifies the LM27965SQ-M, while address 0x36 is assigned to LM27965SQ. This distinction matters when two driver channels share a common serial bus or when firmware must identify the installed device.

The 24-pin leadless package supports compact display construction while exposing group-enable, brightness-control, reset, and LED-current programming functions. Board layouts should preserve short LED current paths, place input and charge-pump capacitors near their associated pins, and maintain adequate copper around the exposed pad for thermal and layout performance.

This product page combines manufacturer specifications, family-level drop-in options, package and pin-location guidance, pricing structure, application analysis, and design notes. It is intended to help engineers evaluate the LM27965SQ-M for compact dual-display backlighting, portable media equipment, and other white-LED systems requiring precise current matching and serial dimming.

חלופות תחליף ישיר עבור LM27965SQ-M — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

LM27965SQ/NOPB

✅ Drop-In
📦 WQFN-24 (RTW)
Identical 9-output and 180 mA charge-pump architecture, but I2C address is 0x36 instead of 0x38, requiring an address change in firmware.

📋 חלופה להתייחסות (לא בקטלוג)

LM27965SQX

✅ Drop-In
📦 WQFN-24 (RTW)
Same 24-WQFN LED-driver package and 9-output family architecture; exact electrical and ordering differences are .

📋 חלופה להתייחסות (לא בקטלוג)

LM27965SQ-M דירוגים מרביים ומאפיינים חשמליים

Product Type Dual-display white LED driver
Charge-Pump Topology Adaptive 1× to 3/2× switched-capacitor
LED Output Count 9 outputs
Total LED Drive Current 180 mA
Maximum Current per LED 30 mA per LED
טווח מתח כניסה 2.7 V to 5.5 V
תדר מיתוג 1.27 MHz
Peak LED Drive Efficiency 91%
Current Matching 0.3%
Independently Controlled Output Groups 3 groups
Primary Group Configuration 4 or 5 LEDs
Secondary Group Configuration 4 LEDs
I2C Chip Address 0x38
Brightness Control I2C-compatible
Reset Control External chip RESET pin
Inductor Requirement No inductor required
מארז 24-pin WQFN (RTW)
Package Dimensions 4 mm × 4 mm × 0.8 mm
Total Solution Size 25 mm²
סוג הרכבה Surface mount
טווח טמפרטורת פעולה -30°C to +85°C

מדריך תצורת פינים של LM27965SQ-M 4 mm × 4 mm × 0.8 mm

תצורת פינים עבור LM27965SQ-M (מארזת 4 mm × 4 mm × 0.8 mm). רכיב הספק זה כולל מסופי שער, ניקוז ומקור. במארזים לא מקוטבים, יש לעיין בגיליון הנתונים של היצרן לכיוון מדויק של פין 1 ולפרטי טביעת רגל. יישומים נפוצים כוללים תכנון ספקי כוח, הנעת מנועים והחלפת עומסים.

תרשים פינים של מארזת 4 mm × 4 mm × 0.8 mm עבור LM27965SQ-M

אין נתוני פריסת פינים מפורטים עבור LM27965SQ-M.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

LM27965SQ-M מתאים עבור 6 יישוםs: Compact Dual-Display LCD Backlighting, Tablet and Portable Media Equipment, Automotive or Industrial Display Modules, White-LED Signage and General Illumination, Battery-Powered Instrument and Sensor Displays, Multi-Display Control Systems.

📺

Compact Dual-Display LCD Backlighting

The LM27965SQ-M is well suited to compact displays that need several independently controlled white-LED groups. Its nine constant-current outputs and three controlled groups allow a primary group of four or five LEDs and a secondary group of four LEDs to share one driver. The 0.3% current matching specification helps maintain consistent luminance across the array, while the 4 mm × 4 mm WQFN package preserves board area. Its adaptive 1× to 3/2× charge pump also removes the inductor normally associated with a boost converter.

📱

Tablet and Portable Media Equipment

The LM27965SQ-M fits portable media equipment where display lighting must be compact, adjustable, and powered from a 2.7 V to 5.5 V source. Its input range covers extended Li-ion operating conditions, and I2C-compatible brightness control lets a host processor adjust illumination without dedicating multiple PWM outputs. With no inductor required and up to 180 mA total LED drive, the device provides useful integration density. Designers should confirm LED forward voltage, charge-pump headroom, and thermal performance in the finished enclosure.

🏭

Automotive or Industrial Display Modules

The LM27965SQ-M can support compact instrument panels and display modules requiring controlled LED current over a 2.7 V to 5.5 V input range. Constant-current sinking limits brightness variation as supply voltage or LED forward voltage changes, and the 0.3% matching specification supports uniform illumination. The device's external RESET pin and I2C dimming interface simplify integration with system controllers. Industrial qualification details are not stated on the manufacturer product page, so the target application's environmental and automotive requirements must be reviewed separately.

💡

White-LED Signage and General Illumination

The LM27965SQ-M can drive grouped white-LED arrays where I2C brightness control and consistent channel current are valuable. Up to nine outputs and 180 mA total current provide enough scale for compact illuminated surfaces, while three independently controlled groups permit separate brightness regions or visual effects. The 1.27 MHz switched-capacitor implementation avoids an inductor and supports a compact solution. For signage, validate ambient temperature, LED forward-voltage spread, current-setting resistors, and the maximum continuous operating time of the selected group.

🔧

Battery-Powered Instrument and Sensor Displays

The LM27965SQ-M is useful in battery-powered instruments because it accepts 2.7 V to 5.5 V input and integrates the switched-capacitor LED supply into one small package. I2C-compatible brightness control allows the system controller to reduce display illumination when power is constrained. The driver can maintain separate brightness control over three LED groups without requiring external inductors. Battery-system designers should still calculate average and peak input current, verify the charge-pump's available headroom at the lowest battery voltage, and confirm that the display's forward voltage remains within the operating region.

🖥️

Multi-Display Control Systems

The LM27965SQ-M supports control systems that require more than one illuminated area and structured brightness management. Three independently controlled output groups can operate distinct LED regions, while I2C-compatible brightness control centralizes adjustment. Its dedicated external RESET pin provides a defined way to coordinate the driver with other system blocks. When more than one LM27965 family device shares a bus, select address 0x38 for the -M variant or 0x36 for LM27965SQ, then verify timing and address behavior across the complete startup sequence.

סיכום מוצרים מומלצים

LM27965SQ-M Texas Instruments בשימוש ב-: Compact Dual-Display LCD Backlighting, Tablet and Portable Media Equipment, Automotive or Industrial Display Modules, White-LED Signage and General Illumination, Battery-Powered Instrument and Sensor Displays, Multi-Display Control Systems LM27965SQ/NOPB Footprint-compatible family alternative with I2C address 0x36 בשימוש ב-: Compact Dual-Display LCD Backlighting, Automotive or Industrial Display Modules, Battery-Powered Instrument and Sensor Displays, Multi-Display Control Systems LM27965SQX Same-family WQFN LED-driver option בשימוש ב-: Tablet and Portable Media Equipment, White-LED Signage and General Illumination
What is the operating voltage of LM27965SQ-M?
The LM27965SQ-M operates from 2.7 V to 5.5 V at its input. According to the Texas Instruments LM27965 product page, this range supports extended Li-ion input conditions while an adaptive 1× to 3/2× charge pump generates the LED drive voltage. No external inductor is required, and the selected charge-pump ratio should be checked against the LED forward voltage, programmed sink current, and expected output voltage drop.
How many LEDs and how much current can LM27965SQ-M drive?
The LM27965SQ-M can drive up to nine LEDs and 180 mA of total output current, with up to 30 mA available per LED. Texas Instruments describes three independently controlled LED-current groups: a primary group configurable for four or five LEDs and a secondary group configurable for four LEDs. Per-LED current is resistor-programmable, allowing the same device to serve unequal LED groups while retaining constant-current operation.
What are the key specifications of LM27965SQ-M that engineers should know?
The LM27965SQ-M combines nine constant-current LED outputs, a 2.7 V to 5.5 V input range, and I2C-compatible dimming in a 24-pin WQFN package. Texas Instruments specifies up to 180 mA total current, 30 mA per LED, 0.3% current matching, 91% peak LED-drive efficiency, and a 1.27 MHz switching frequency. Its adaptive 1× to 3/2× charge pump eliminates an external inductor.
Where can I download the LM27965SQ-M datasheet PDF?
The LM27965SQ-M documentation is available through the official Texas Instruments LM27965 product page and the manufacturer-linked datasheet resources. The device is documented as a dual-display white LED driver with I2C-compatible brightness control. Use the pin-description table, application circuit, current-setting equations, and timing diagrams in the manufacturer datasheet when assigning the 24 RTW package connections or calculating resistor values.
Where can I find the LM27965SQ-M pinout?
The LM27965SQ-M uses a 24-pin WQFN (RTW) package, and its authoritative pin assignments appear in the Texas Instruments LM27965 datasheet pin-description table. The exact numbered pin names are not reproduced on the product page, so use the datasheet for PCB routing and verify the exposed-pad connection before layout release. The package itself measures 4 mm × 4 mm × 0.8 mm.
What is the I2C address of LM27965SQ-M?
The LM27965SQ-M uses I2C-compatible chip address 0x38. Texas Instruments specifies 0x36 for the LM27965SQ and 0x38 for the LM27965SQ-M. Firmware must program the correct seven-bit address before attempting brightness or configuration writes. The address distinction is especially important when multiple driver ICs share the same I2C bus.
LM27965SQ-M vs LM27965SQ - which is better for a shared I2C bus?
The LM27965SQ-M is the better choice when firmware expects I2C address 0x38, while the LM27965SQ uses address 0x36. Texas Instruments identifies both as dual-display, nine-output charge-pump LED drivers with resistor-programmable current and the same 24-pin WQFN (RTW) package. Select the device whose address matches the board firmware and verification plan rather than treating the two orderable variants as interchangeable at the software level.
When should I choose LM27965SQ-M over LM27965SQ?
Choose LM27965SQ-M when the system firmware addresses the LED driver at 0x38 or when the approved BOM specifically requires the -M device. Both devices provide the same core 2.7 V to 5.5 V input range, nine constant-current outputs, 180 mA maximum aggregate drive, adaptive charge-pump operation, and 24-pin WQFN construction. The primary selection criterion is therefore the assigned I2C address and exact ordering code.
Is LM27965SQ-M suitable for compact LCD backlighting?
The LM27965SQ-M is suitable for compact dual-display backlighting because it integrates nine constant-current outputs, three independently controlled groups, resistor-programmable current, and I2C brightness control into one 4 mm × 4 mm package. Its adaptive charge pump avoids an inductor, while 0.3% current matching supports visually uniform illumination. The design must still verify LED forward voltage, available headroom, thermal conditions, and group configuration.
What is the best drop-in replacement for LM27965SQ-M?
The closest documented drop-in option is LM27965SQ/NOPB because it uses the same 24-WQFN (4 mm × 4 mm) package and retains the nine-output, 30 mA-per-LED, 180 mA-total charge-pump architecture. The critical replacement difference is its I2C address: 0x36 instead of the LM27965SQ-M's 0x38. Firmware or hardware changes may therefore be required despite the matching footprint.
Can LM27965SQ/NOPB replace LM27965SQ-M without a PCB change?
LM27965SQ/NOPB can fit the same 24-WQFN footprint and provides a closely matched LED-driver configuration, but it is not a software-identical substitution. Texas Instruments assigns address 0x36 to LM27965SQ/NOPB and address 0x38 to LM27965SQ-M. The PCB may remain unchanged, while firmware must use the correct address and the system should be revalidated for enable, reset, and dimming behavior.
What can replace LM27965SQ-M?
LM27965SQ/NOPB is the principal documented replacement for LM27965SQ-M because it retains the same 24-pin WQFN footprint, nine LED outputs, 180 mA total-current capability, and I2C dimming architecture. It changes the chip address from 0x38 to 0x36, so designers should treat it as a drop-in hardware option that may require an I2C-address firmware update. Verify startup, reset, and all three output groups after substitution.
Is LM27965SQ-M the same as LM27965SQ/NOPB?
No, LM27965SQ-M and LM27965SQ/NOPB are closely related but not identical in firmware addressing. The LM27965SQ-M uses I2C address 0x38, whereas LM27965SQ/NOPB uses 0x36. Both share the 24-WQFN package and core dual-display LED-driver functions, so the footprint can be reused while the bus address and associated configuration must be reconciled.
Where to buy LM27965SQ-M online?
Use the Request a Quote form on this page to request LM27965SQ-M availability, current commercial terms, and order quantities. The form is the appropriate route for a quote-based sourcing decision and avoids publishing a transient price or stock claim. Confirm the exact -M ordering code, 24-pin WQFN (RTW) package, reel quantity, and any required NOPB marking before releasing the purchase order.
What is the price and lead time of LM27965SQ-M?
Submit the LM27965SQ-M Request a Quote form on this page for the current commercial terms, lead time, and minimum order quantity. The exact MPN and package configuration should be included in the request so the manufacturer or authorized channel can confirm the correct 24-pin RTW variant. Inventory and delivery timing can change, making a live quotation more reliable than a static price claim.
Is LM27965SQ-M in stock?
Current LM27965SQ-M inventory should be requested through the Request a Quote form on this page. Include the required quantity, reel packaging preference, target date, and whether an NOPB-marked version is required. This avoids treating a distributor search result as a guarantee of stock and helps distinguish a production buy from an evaluation or prototype order.
How does LM27965SQ-M regulate LED current?
The LM27965SQ-M regulates LED current with dedicated constant-current sinks, while an adaptive 1× to 3/2× switched-capacitor charge pump supplies the required drive voltage. Texas Instruments specifies resistor-programmable current settings, up to 30 mA per LED, 0.3% current matching, and 91% peak drive efficiency. The exact sink-setting equations and charge-pump operating conditions should be calculated from the manufacturer datasheet.
What design considerations apply to LM27965SQ-M layouts?
Place the LM27965SQ-M input, flying-capacitor, and output-loop components close to their associated pins to minimize parasitic inductance and preserve charge-pump performance. Keep LED-current traces compact and away from sensitive analog or communication nodes, connect the exposed pad according to the datasheet, and verify thermal limits using actual board copper and enclosure conditions. Correct I2C address configuration is also essential when more than one driver shares the bus.

נתוני עזר הנדסיים עבור LM27965SQ-M — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the LM27965SQ-M when the design requires nine constant-current LED outputs, 2.7 V to 5.5 V input, I2C brightness control, and the specific 0x38 chip address. It is especially attractive for compact dual-display backlighting because three controlled groups, resistor-programmable current up to 30 mA per LED, and an inductor-free adaptive charge pump reduce board area. LM27965SQ/NOPB is the closest documented hardware alternative when 0x36 is the desired bus address, but firmware must be changed or configured accordingly. LM27965SQX may suit a related 24-WQFN family configuration, although its complete electrical details should be verified before substitution. For any alternative, verify pin assignments, LED-current limits, charge-pump headroom, startup behavior, reset polarity, and the exact ordering code against the manufacturer datasheet.

השוואה עם חלופות

פרמטר מוצר זה LM27965SQ/NOPB LM27965SQX
Package WQFN-24 (RTW), 4 mm × 4 mm WQFN-24 (RTW), 4 mm × 4 mm WQFN-24 (RTW)
Brand Texas Instruments Texas Instruments Texas Instruments
LED Output Count 9 outputs 9 outputs 9 outputs

מבדילים עיקריים

  • Assigned 0x38 I2C address (לעומתLM27965SQ/NOPB)
  • Nine-output dual-display integration (לעומתLM27965SQ/NOPB)
  • Inductor-free compact implementation (לעומתLM27965SQX)

הערות תכנון

Place the LM27965SQ-M input capacitor, flying capacitor, and output-loop components directly beside the pins specified by the manufacturer application circuit. These switched-capacitor connections carry high-frequency current, so long loops increase parasitic inductance, ringing, and EMI. Keep the 24-WQFN exposed-pad connection and thermal copper consistent with the datasheet land pattern, and avoid placing sensitive analog or high-speed communication traces beneath the charge-pump return path.

Do not assume that LM27965SQ and LM27965SQ-M are firmware-identical. The -M device uses I2C address 0x38, while LM27965SQ uses 0x36. Confirm the assembled part marking and update bus-address constants before power-up. Also verify the charge-pump output has sufficient voltage headroom above the highest LED forward voltage and programmed sink current; otherwise brightness may be reduced or current regulation may move outside its intended operating region.

Estimated: use Pdissipation = (VIN - VLED) × ILED to estimate charge-pump loss at the maximum aggregate LED current of 180 mA. For example, at 5.5 V input, 3.6 V LED voltage, and 180 mA load, the estimated power loss is 0.342 W before accounting for control overhead and conversion efficiency. Confirm the actual junction-temperature rise using the package thermal data and the finished PCB copper area rather than relying on the calculation alone.

Calculate LED current-setting resistors from the manufacturer equations and include the LED forward-voltage spread, resistor tolerance, and sink accuracy. Check that no group exceeds 30 mA per LED and that the aggregate does not exceed 180 mA. Because brightness is adjusted through the serial interface, test the minimum, nominal, and maximum dimming settings while monitoring the input rail and charge-pump output for droop or unstable regulation.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The manufacturer product page and part-detail result do not explicitly state the requested environmental compliance status. The -M ordering code is not treated as proof of lead-free or halogen-free status.

הנתונים אומתו בתאריך: 2026-11-20 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

LM27965SQ-M datasheet LM27965SQ-M pinout LM27965SQ-M datasheet pdf LM27965SQ-M specifications Texas Instruments LM27965SQ-M LM27965SQ-M WQFN-24 pinout LM27965SQ-M LED driver application circuit LM27965SQ-M vs LM27965SQ/NOPB LM27965SQ-M replacement LM27965SQ-M equivalent LM27965SQ-M I2C address LM27965SQ-M price LM27965SQ-M stock LM27965SQ-M WQFN-24 footprint

רכיבים ומונחים קשורים

Texas Instruments LM27965SQ-M LM27965SQ/NOPB LM27965SQX dual-display white LED driver LED driver charge-pump driver switched-capacitor converter constant-current sink I2C brightness control PWM dimming adaptive 1× to 3/2× charge pump WQFN-24 RTW package QFN family surface-mount package LCD backlight white LED portable electronics industrial display 0x38 I2C address 0x36 I2C address current matching 91% peak LED-drive efficiency
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר