LM2902KVQPWRG4 - 30V Quad Op Amp | Texas Instruments
MPN: LM2902KVQPWRG4 ✓ פעילLM2902KVQPWRG4 סקירה
An operational amplifier is a voltage-feedback amplifier used to amplify differential signals and drive high-impedance loads. Within the broader semiconductor hierarchy, this quad device belongs to the operational-amplifier family, analog amplifier IC category, and general-purpose signal-conditioning ecosystem. Four amplifiers in one package reduce board area and simplify designs requiring several independent analog channels.
The LM2902KV generation improves electrical characteristics while retaining compatibility with established LM224, LM324, and LM2902 applications. Its 30 V maximum supply rating supports higher-voltage analog systems than conventional 26 V quad op amps. A 1.2 MHz gain-bandwidth product supports general-purpose closed-loop signal processing, while the stated 80 dB common-mode rejection ratio helps suppress output response to common-mode input variation. Improved 2 kV ESD protection strengthens robustness in exposed industrial environments.
Each amplifier includes high open-loop gain, differential input capability, and internal frequency compensation. The device can operate from a single supply or from positive and negative rails, making it suitable for bipolar signal conditioning around a zero-volt reference. Its common-mode input range, output swing limits, input-bias current, and input-offset-voltage limits should be checked against the system’s signal levels and supply headroom before finalizing a design.
Typical uses include industrial sensor interfaces, low-frequency active filters, transducers, audio preamplifier stages, analog-to-digital converter input conditioning, and general feedback-control circuits. Four independent channels are especially useful when a design needs several filtered or buffered signals and board area is constrained. The 14-pin TSSOP package supports compact surface-mount assemblies while exposing all four amplifier sections.
For stable operation, use the manufacturer-recommended bypass capacitors close to the supply pins, maintain adequate output-load capacitance, and verify operation across the complete -40°C to 125°C temperature range. Input and output voltages must remain within the device’s absolute-maximum and common-mode limits. Stable feedback-network design is also essential when operating at higher frequencies or with nonstandard gain settings.
This product page organizes the manufacturer’s principal operating limits, package information, pin assignment, verified commercial parameters, and practical design guidance. It also distinguishes the closest same-footprint alternatives by supply rating, precision grade, temperature range, and ESD capability so engineers can make a replacement decision without changing the PCB land pattern.
חלופות תחליף ישיר עבור LM2902KVQPWRG4 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LM2902KVQPWRG4 (אותו גורם צורה וטביעת רגל) — שונים ב Package.
LM2902PWRG4
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2902QPWRG4
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
LM2902KPWRG4
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
LM2902KVQPWR
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2902KVQPWRG4 דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Amplifier Channels | 4 channels |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Improved ESD Protection | 2 kV |
| טווח טמפרטורת פעולה | -40°C to 125°C |
| Common-Mode Rejection Ratio | 80 dB |
| Slew Rate | 0.5 V/µs |
| Input Bias Current | -0.5 µA |
| Low Input Offset Voltage | ±3 mV standard grade; ±2 mV BA grade |
| Package Type | 14-pin TSSOP (PW) |
| מספר פינים | 14 pins |
| סוג הרכבה | Surface mount |
| Supply Configuration | Single supply or split supply |
| Internal Frequency Compensation | One-compensator architecture per amplifier channel |
| Automotive Qualification | AEC-Q100 qualified |
תצורת פינים של LM2902KVQPWRG4
| פין 1 | OUT1 — Amplifier 1 output |
| פין 2 | IN1- — Amplifier 1 inverting input |
| פין 3 | IN1+ — Amplifier 1 non-inverting input |
| פין 4 | V- — Negative supply connection |
| פין 5 | IN2+ — Amplifier 2 non-inverting input |
| פין 6 | IN2- — Amplifier 2 inverting input |
| פין 7 | OUT2 — Amplifier 2 output |
| פין 8 | OUT3 — Amplifier 3 output |
| פין 9 | IN3- — Amplifier 3 inverting input |
| פין 10 | IN3+ — Amplifier 3 non-inverting input |
| פין 11 | V+ — Positive supply connection |
| פין 12 | IN4+ — Amplifier 4 non-inverting input |
| פין 13 | IN4- — Amplifier 4 inverting input |
| פין 14 | OUT4 — Amplifier 4 output |
יישומים טיפוסיים
LM2902KVQPWRG4 מתאים עבור 6 יישוםs: Industrial Sensor Signal Conditioning, Active Filters and Audio Preamplification, ADC and DAC Interface Conditioning, Power Supply Feedback and Monitoring, Process Control and Instrumentation, Portable and Automotive-Assisted Control Modules.
Industrial Sensor Signal Conditioning
The LM2902KVQPWRG4 is well suited to conditioning low-level sensor signals in industrial electronics because it combines four independent channels with a 1.2 MHz gain-bandwidth product and 80 dB common-mode rejection ratio. Its -40°C to 125°C operating range supports equipment exposed to temperature variation, while the 30 V supply rating accommodates 24 V industrial rails with suitable transient protection. The device can implement differential input stages, gain blocks, anti-alias filters, and output drivers around a common sensor-conditioning board. Four channels also reduce package count and simplify routing when several transducers are present. Designers should still verify the input common-mode range against sensor output levels and ensure that source impedance does not degrade offset or bias-current performance.
מומלץ
Active Filters and Audio Preamplification
With a 1.2 MHz gain-bandwidth product and 0.5 V/µs slew rate, the LM2902KVQPWRG4 can implement general-purpose active filters and low-frequency preamplifier sections. Four channels permit cascaded filter stages, dual-channel audio paths, or a mixture of filtering and gain functions in one 14-pin TSSOP. The 80 dB common-mode rejection ratio helps preserve signal integrity when both inputs are near the same reference voltage, which is common in single-supply audio and control circuits. Stable operation depends on the selected gain, resistor values, load, and output-capacitance limits described by the manufacturer. Keep the feedback network compact and provide the specified bypass capacitance to minimize oscillation risk.
מומלץ
ADC and DAC Interface Conditioning
The LM2902KVQPWRG4 can provide buffering, level shifting, differential amplification, and active filtering in mixed-signal systems connected to ADCs or DACs. Its 1.2 MHz gain-bandwidth product is appropriate for many low- and moderate-frequency instrumentation channels, while four amplifiers allow several converter inputs or outputs to be conditioned independently. The common-mode rejection ratio of 80 dB reduces output movement caused by shared ground or supply disturbances. Because the output swing and input common-mode range depend on the supply voltage, designers must compare converter signal limits with the device’s operating region. A solid ground plane and local supply bypassing are especially important when high-impedance sensor outputs are converted with millivolt-level resolution.
מומלץ
Power Supply Feedback and Monitoring
The LM2902KVQPWRG4 can amplify the error voltage in a linear regulator or form part of a power-supply monitoring circuit. Its 30 V supply rating is useful in 12 V and 24 V systems, while the 1.2 MHz bandwidth permits feedback loops intended for relatively slow power rails rather than high-frequency switching converters. The four-channel configuration can monitor several supply rails, sense input dividers, amplify comparator signals, and buffer reference nodes. Feedback compensation must be designed around the specific regulator control loop rather than copied directly from a generic op-amp example. Keep the feedback divider close to the regulator and separate sensitive sensing routes from high-current switching paths to reduce injected noise and ground-bounce errors.
מומלץ
Process Control and Instrumentation
The LM2902KVQPWRG4 is applicable to process-control modules that combine several low-frequency analog signals, including thermocouple-style amplifiers, valve-driver interfaces, current-loop conditioning, and output scaling. Its -40°C to 125°C range suits equipment operating across industrial temperature zones, and the 30 V capability provides headroom for 24 V control loops. The four channels can reduce component count in compact controller boards while maintaining independent compensation and gain settings. Care is required near grounded thermocouple junctions because input bias current and offset voltage can create meaningful errors in microvolt-level systems. Use low-leakage input protection networks, clean reference grounding, and shielded analog routing when the source impedance is high.
מומלץ
Portable and Automotive-Assisted Control Modules
The LM2902KVQPWRG4 can be used in compact control modules requiring four general-purpose analog channels and operation over an extended temperature range. The 14-pin TSSOP package helps limit board area, while the 30 V rating and improved 2 kV ESD capability support 12 V or 24 V systems with appropriate transient suppression. Applications include actuator interfaces, battery monitoring, fan-control analog sections, and vehicle or industrial accessory modules. The automotive-related suitability of the family does not replace project-specific qualification of the exact ordering variant. Engineers must verify the exact temperature grade, ESD qualification, automotive qualification status, and production requirements before using the device in a safety-related or high-volume automotive design.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LM2902KVQPWRG4 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LM2902PWRG4 | LM2902QPWRG4 | LM2902KPWRG4 | LM2902KVQPWR |
|---|---|---|---|---|---|
| Package | TSSOP-14 (PW) | TSSOP-14 (PW) - same | TSSOP-14 (PW) - same | TSSOP-14 (PW) - same | TSSOP-14 (PW) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Maximum Supply Voltage | 30 V | 26 V | 26 V | 26 V | 30 V |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Number of Channels | 4 | 4 | 4 | 4 | 4 |
מבדילים עיקריים
- Higher supply-voltage capability within the same 14-pin TSSOP family (לעומתLM2902PWRG4)
- Improved ESD capability for exposed analog interfaces (לעומתLM2902PWRG4)
- Extended-temperature operation for industrial systems (לעומתLM2902NG)
הערות תכנון
Place the required bypass capacitors directly between the V+ and V- pins and their nearest ground-plane connections. Keep these loops short because trace inductance can couple switching noise into the amplifier output. The 30 V supply rating leaves room above a 24 V rail, but it is not a transient withstand rating; add suitable surge and reverse-polarity protection wherever industrial wiring can exceed the nominal supply.
Route each differential input pair together and avoid routing them parallel to power-supply or switching-node traces. Maintain a continuous ground reference beneath the inputs and feedback resistors, and keep unused amplifier channels in a defined, stable state rather than allowing them to float. The 14-pin TSSOP footprint has closely spaced supply and signal pins, so inspect the manufacturer’s land pattern and solder-mask recommendations before releasing artwork.
Do not assume that a 30 V maximum supply rating permits 30 V input signals at every pin. Check the absolute-maximum table, input common-mode range, output swing, and power-versus-current limits in the LM2902KV datasheet. Also verify offset voltage and input-bias-current effects when the source impedance is high; 80 dB common-mode rejection does not eliminate errors caused by bias current through unequal source resistances.
מידע על תאימות
The family is identified as AEC-Q100 qualified for automotive applications. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer declaration or product documentation.