LM293DGKR - Dual 2-36V Comparator | Texas Instruments
MPN: LM293DGKR ✓ פעילLM293DGKR סקירה
A differential comparator is an analog integrated circuit that compares two input voltages and produces a binary output indicating which input is higher. The LM293 belongs to the voltage-comparator hierarchy within interface and signal-conditioning semiconductors. Its two channels can operate independently, allowing one package to perform two comparison functions while reducing board area and simplifying component procurement.
The principal operating characteristics include a 2 V to 36 V supply range, a 300 ns response time, and approximately 200 uA supply current. The open-collector outputs can sink useful levels of output current while the external pull-up resistor determines the high output voltage. Rail-to-rail input operation is identified for this device, while its industrial operating range of -40 C to +85 C supports laboratory, control-system, and industrial equipment.
Each internal channel compares its noninverting and inverting inputs. Because the outputs are open collector, both channels can be tied together when wired-OR logic is required. The low output saturation behavior also permits direct interfacing with TTL, MOS, and CMOS-compatible external circuitry. Separate ground, supply, input, and output connections make the device straightforward to use in both single-supply and split-supply arrangements, subject to the applicable input limits.
Typical uses include power-rail monitoring, industrial sensor threshold detection, battery and charger supervision, window-comparator circuits, control-loop signal conditioning, and logic-level translation where an open-drain interface is advantageous. The dual-channel configuration is particularly useful when a design requires two related decisions, such as an upper threshold and a lower threshold around the same monitored quantity.
Designers should select an external pull-up resistor for each open-collector output and confirm that its resistance keeps output rise time and sink current within system requirements. Input and supply connections should be kept short, with suitable local bypassing placed close to the device. Thermal and common-mode limits must be checked across the full operating range, especially in industrial systems with long wiring and noisy power sources.
This product overview combines the LM293 family identity, verified package and ordering information, practical comparator design guidance, drop-in family alternatives, and a specification comparison intended to accelerate component selection and PCB planning.
חלופות תחליף ישיר עבור LM293DGKR — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LM293DGKR (אותו גורם צורה וטביעת רגל) — שונים ב Package, Output Type, Comparator Type, Supply Voltage Range.
LM293ADGKRG4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LM393DGKR
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2903DGKRG4
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM193DGKR
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
LM293DGKR דירוגים מרביים ומאפיינים חשמליים
| Comparator Type | Dual differential voltage comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2 V to 36 V |
| Response Time | 300 ns |
| זרם אספקה | Approximately 200 uA |
| סוג פלט | Open-collector |
| Input Common-Mode Range | Rail-to-rail |
| טווח טמפרטורת פעולה | -40 C to +85 C |
| מארז | 8-pin VSSOP |
| מספר פינים | 8 pins |
| סוג הרכבה | Surface mount |
| Logic Compatibility | TTL, MOS, and CMOS compatible |
| Single-Supply Operation | Supported |
| Split-Supply Operation | Supported |
| Differential Input Voltage | ±38 V maximum |
| Differential Input Offset Voltage | 5 mV maximum |
| Input Bias Current | 250 nA maximum |
| Output Saturation Voltage | 100 mV maximum at 16 mA output current |
| סטטוס RoHS | Compliant |
| Lead-Free Status | Lead-free |
| סטטוס מחזור חיים | Active |
מדריך תצורת פינים של LM293DGKR 8-pin vssop
תצורת פינים עבור LM293DGKR (מארזת 8-pin vssop). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור LM293DGKR.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
LM293DGKR מתאים עבור 6 יישוםs: Industrial Power-Rail Monitoring, Battery Charger Threshold Control, Industrial Sensor Threshold Detection, Motor Control and Feedback Monitoring, Window Comparator for Setpoint Limits, Logic-Level Interface and Fault Signaling.
Industrial Power-Rail Monitoring
The LM293DGKR fits industrial rail supervision because its two channels can compare a measured supply against independent upper and lower reference levels. The 2 V to 36 V operating range supports common industrial voltage systems, while the 300 ns response permits rapid state changes. Each open-collector output can drive a fault indicator or wired-alarm node through an external pull-up resistor. Designers should choose resistor values that balance rise time against sink current and verify transient margins when monitoring long field-wired supplies.
מומלץ
Battery Charger Threshold Control
The LM293DGKR can supervise charge, discharge, or fault thresholds in a battery system using its two differential comparator channels. A 300 ns response time supports prompt switching when a control signal crosses its reference, and the open-collector outputs provide flexible pull-up-defined logic levels. The device is suitable only when charger transients remain within its specified input and supply limits, so designers should include filtering for switching nodes and verify the absolute maximum differential input rating of ±38 V.
מומלץ
Industrial Sensor Threshold Detection
The LM293DGKR converts a sensor-derived analog voltage into a logic decision by comparing it with a reference. Its dual-channel architecture allows one channel to detect an upper operating limit while the other identifies a lower limit, reducing component count in window-detection circuits. The 2 V to 36 V supply range supports industrial interfaces, while the open-collector outputs can be pulled up to the voltage required by the downstream PLC, counter, or monitoring system.
מומלץ
Motor Control and Feedback Monitoring
The LM293DGKR can monitor motor-control signals, current-sense outputs, or feedback voltages where a clean binary decision is required. Its 300 ns response time is useful for detecting excursions rapidly, and the two independent channels can supervise separate aspects of the control loop. Open-collector outputs permit wired-OR fault reporting, but care is required near switching nodes; input filtering and trace placement should prevent high-current transients from violating the specified common-mode and differential-input limits.
מומלץ
Window Comparator for Setpoint Limits
Two LM293DGKR channels can form a window comparator that flags when a measured voltage moves above or below intended limits. The open-drain outputs may be tied together for a single active-low out-of-range indication, provided the design uses an appropriate pull-up and accounts for the combined sink current. The 2 V to 36 V supply range accommodates many process-control and test systems, while the 300 ns response reduces delay when limits are crossed.
מומלץ
Logic-Level Interface and Fault Signaling
The LM293DGKR is useful when a system needs open-collector fault signaling rather than a push-pull logic output. An external pull-up resistor establishes the high state and allows the interface voltage to match the receiving TTL, MOS, or CMOS circuit. The two channels can monitor separate conditions and share a wired-OR node where appropriate. Designers should calculate the pull-up rise time for the target bus capacitance, verify the output sink rating, and account for the device’s 300 ns response and industrial -40 C to +85 C range.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LM293DGKR — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LM293ADGKRG4 | LM393DGKR | LM2903DGKR | LM193DGKR |
|---|---|---|---|---|---|
| Package | 8-pin VSSOP | 8-pin VSSOP | 8-pin VSSOP | 8-pin VSSOP | 8-pin VSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Type | Dual differential comparator | Dual general-purpose differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Number of Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Supply Voltage Range | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V |
| Response Time | 300 ns | 300 ns | 300 ns | 300 ns | 300 ns |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Operating Temperature Range | -40 C to +85 C | -55 C to +125 C | -40 C to +85 C | -40 C to +85 C | -55 C to +125 C |
מבדילים עיקריים
- Exact LM293 family continuity in an 8-pin VSSOP (לעומתLM393DGKR)
- Industrial temperature range matched to standard equipment (לעומתLM193DGKR)
- Dual open-collector channels in one compact package (לעומתLM2903DGKR)
- 300 ns response for fast threshold decisions (לעומתLM293ADGKRG4)
הערות תכנון
Route the open-collector outputs away from sensitive input and reference nodes because the pull-up edge can produce fast voltage transitions. Keep the two differential input pairs close together and connect their ground returns through a low-impedance path. Place input filtering near the source when sensing noisy industrial signals, but ensure added capacitance does not upset the intended switching response or reference settling.
Do not operate an open-collector output without an external pull-up resistor; the output cannot reach a valid high level by itself. Select the pull-up from the receiver’s voltage requirement and the required edge rate. When tying both comparator outputs together for wired-OR operation, include the combined sink current in the calculation and confirm that the resulting common output polarity matches the downstream logic.
Check supply sequencing against every input voltage, including the ±38 V differential input limit. A comparator may remain within its supply range while an input transient exceeds the allowed differential or common-mode limit. Use series resistance, clamps, or filtering where long external wiring can introduce transients, and verify the configuration across both startup and shutdown rather than only during steady-state operation.
The LM293DGKR’s industrial -40 C to +85 C rating applies to the specified supply and electrical conditions. Place the 8-pin VSSOP on a PCB with adequate ground connectivity and avoid placing it beside a high-temperature regulator without thermal analysis. Since the device is primarily a low-power comparator, normal copper spreading is usually more relevant than a large external heatsink, but final thermal performance depends on the board and enclosure.
מידע על תאימות
RoHS-compliant and lead-free status is identified for LM293DGKR. Automotive qualification is not indicated for this industrial-grade orderable part.