Texas Instruments

LM293DGKR - Dual 2-36V Comparator | Texas Instruments

MPN: LM293DGKR ✓ Aktif
2 V to 36 V Vdss Approximately 200 uA Id 8-pin VSSOP Package
MOQ: 1 |

LM293DGKR Ringkasan

The Texas Instruments LM293DGKR is a dual differential comparator with two independent comparator channels, a 2 V to 36 V supply range, and a 300 ns response time, housed in an 8-pin VSSOP package. Each channel uses open-collector output architecture, making the device suitable for wired logic interfaces, threshold detection, and systems requiring a pull-up resistor.

A differential comparator is an analog integrated circuit that compares two input voltages and produces a binary output indicating which input is higher. The LM293 belongs to the voltage-comparator hierarchy within interface and signal-conditioning semiconductors. Its two channels can operate independently, allowing one package to perform two comparison functions while reducing board area and simplifying component procurement.

The principal operating characteristics include a 2 V to 36 V supply range, a 300 ns response time, and approximately 200 uA supply current. The open-collector outputs can sink useful levels of output current while the external pull-up resistor determines the high output voltage. Rail-to-rail input operation is identified for this device, while its industrial operating range of -40 C to +85 C supports laboratory, control-system, and industrial equipment.

Each internal channel compares its noninverting and inverting inputs. Because the outputs are open collector, both channels can be tied together when wired-OR logic is required. The low output saturation behavior also permits direct interfacing with TTL, MOS, and CMOS-compatible external circuitry. Separate ground, supply, input, and output connections make the device straightforward to use in both single-supply and split-supply arrangements, subject to the applicable input limits.

Typical uses include power-rail monitoring, industrial sensor threshold detection, battery and charger supervision, window-comparator circuits, control-loop signal conditioning, and logic-level translation where an open-drain interface is advantageous. The dual-channel configuration is particularly useful when a design requires two related decisions, such as an upper threshold and a lower threshold around the same monitored quantity.

Designers should select an external pull-up resistor for each open-collector output and confirm that its resistance keeps output rise time and sink current within system requirements. Input and supply connections should be kept short, with suitable local bypassing placed close to the device. Thermal and common-mode limits must be checked across the full operating range, especially in industrial systems with long wiring and noisy power sources.

This product overview combines the LM293 family identity, verified package and ordering information, practical comparator design guidance, drop-in family alternatives, and a specification comparison intended to accelerate component selection and PCB planning.

Pilihan pengganti yang segera untuk LM293DGKR — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera LM293DGKR (sama faktor bentuk dan kaki) — berbeza dalam Package, Output Type, Comparator Type, Supply Voltage Range.

Texas Instruments
Package: 8-VSSOP (8-MSOP, 0.118 inch width)
Comparator Type: Dual differential comparator
Bandingkan Dengan LM293DGKR →
Texas Instruments
Package: 8-pin VSSOP (DGK)
Supply Voltage Range: 3 V to 36 V
Bandingkan Dengan LM293DGKR →
Texas Instruments
Package: 8-VSSOP
Output Type: Open collector
Bandingkan Dengan LM293DGKR →

LM293ADGKRG4

✅ Masuk Drop-In
📦 8-pin VSSOP
Temperature grade differs: A suffix extends the minimum rating from -40 C to -55 C, a 15 C improvement, while retaining the 8-pin VSSOP comparator function.

📋 Alternatif rujukan (tidak dalam katalog)

LM393DGKR

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
Texas Instruments
📦 8-pin VSSOP
Dual differential voltage comparator · 2 independent channels · 2 V to 36 V · 2 V to 36 V · VCC at least 1.5 V more positive than input common-mode voltage · Open collector · Differential inputs on each channel · 8-VSSOP

Hubungi untuk harga

Lihat Datasheet →

LM2903DGKRG4

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
Texas Instruments
📦 8-pin VSSOP
Dual differential comparator · 2 channels · 2 V to 36 V · 2 V to 36 V · 300 ns · Open-collector · Rail-to-rail · 0.4 mA typical

Hubungi untuk harga

Lihat Datasheet →

LM193DGKR

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 8-pin VSSOP
LM193 extends the minimum operating temperature from -40 C to -55 C, a 15 C improvement, while sharing the dual-comparator family and 8-pin VSSOP format.

📋 Alternatif rujukan (tidak dalam katalog)

LM293DGKR Penilaian maksimum & Ciri-ciri Elektrik

Comparator Type Dual differential voltage comparator
Number of Channels 2 channels
Supply Voltage Range 2 V to 36 V
Response Time 300 ns
Arus Pemberi Arus Approximately 200 uA
Jenis Output Open-collector
Input Common-Mode Range Rail-to-rail
Gambaran Suhu Operasi -40 C to +85 C
Kemasan 8-pin VSSOP
Kiraan Pin 8 pins
Jenis Pemasangan Surface mount
Logic Compatibility TTL, MOS, and CMOS compatible
Single-Supply Operation Supported
Split-Supply Operation Supported
Differential Input Voltage ±38 V maximum
Differential Input Offset Voltage 5 mV maximum
Input Bias Current 250 nA maximum
Output Saturation Voltage 100 mV maximum at 16 mA output current
Status RoHS Compliant
Lead-Free Status Lead-free
Status Lingkungan Hidup Active

Panduan Konfigurasi Pin LM293DGKR 8-pin vssop

Konfigurasi pin untuk LM293DGKR (8-pin vssop pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai 8-pin vssop untuk LM293DGKR

Tiada data garisan pin yang diperoleh untuk LM293DGKR.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

LM293DGKR patut untuk 6 aplikasis: Industrial Power-Rail Monitoring, Battery Charger Threshold Control, Industrial Sensor Threshold Detection, Motor Control and Feedback Monitoring, Window Comparator for Setpoint Limits, Logic-Level Interface and Fault Signaling.

🏭

Industrial Power-Rail Monitoring

The LM293DGKR fits industrial rail supervision because its two channels can compare a measured supply against independent upper and lower reference levels. The 2 V to 36 V operating range supports common industrial voltage systems, while the 300 ns response permits rapid state changes. Each open-collector output can drive a fault indicator or wired-alarm node through an external pull-up resistor. Designers should choose resistor values that balance rise time against sink current and verify transient margins when monitoring long field-wired supplies.

⚡

Battery Charger Threshold Control

The LM293DGKR can supervise charge, discharge, or fault thresholds in a battery system using its two differential comparator channels. A 300 ns response time supports prompt switching when a control signal crosses its reference, and the open-collector outputs provide flexible pull-up-defined logic levels. The device is suitable only when charger transients remain within its specified input and supply limits, so designers should include filtering for switching nodes and verify the absolute maximum differential input rating of ±38 V.

🧩

Industrial Sensor Threshold Detection

The LM293DGKR converts a sensor-derived analog voltage into a logic decision by comparing it with a reference. Its dual-channel architecture allows one channel to detect an upper operating limit while the other identifies a lower limit, reducing component count in window-detection circuits. The 2 V to 36 V supply range supports industrial interfaces, while the open-collector outputs can be pulled up to the voltage required by the downstream PLC, counter, or monitoring system.

🔧

Motor Control and Feedback Monitoring

The LM293DGKR can monitor motor-control signals, current-sense outputs, or feedback voltages where a clean binary decision is required. Its 300 ns response time is useful for detecting excursions rapidly, and the two independent channels can supervise separate aspects of the control loop. Open-collector outputs permit wired-OR fault reporting, but care is required near switching nodes; input filtering and trace placement should prevent high-current transients from violating the specified common-mode and differential-input limits.

📊

Window Comparator for Setpoint Limits

Two LM293DGKR channels can form a window comparator that flags when a measured voltage moves above or below intended limits. The open-drain outputs may be tied together for a single active-low out-of-range indication, provided the design uses an appropriate pull-up and accounts for the combined sink current. The 2 V to 36 V supply range accommodates many process-control and test systems, while the 300 ns response reduces delay when limits are crossed.

🖥️

Logic-Level Interface and Fault Signaling

The LM293DGKR is useful when a system needs open-collector fault signaling rather than a push-pull logic output. An external pull-up resistor establishes the high state and allows the interface voltage to match the receiving TTL, MOS, or CMOS circuit. The two channels can monitor separate conditions and share a wired-OR node where appropriate. Designers should calculate the pull-up rise time for the target bus capacitance, verify the output sink rating, and account for the device’s 300 ns response and industrial -40 C to +85 C range.

Ringkasan Produk Disebarkan

LM293 Parent dual-comparator family Dipergunakan di: Industrial Power-Rail Monitoring, Battery Charger Threshold Control, Industrial Sensor Threshold Detection, Motor Control and Feedback Monitoring, Window Comparator for Setpoint Limits, Logic-Level Interface and Fault Signaling LM2903 Related dual-comparator family Dipergunakan di: Industrial Power-Rail Monitoring, Industrial Sensor Threshold Detection, Window Comparator for Setpoint Limits LM393 Texas Instruments Dipergunakan di: Battery Charger Threshold Control, Motor Control and Feedback Monitoring, Logic-Level Interface and Fault Signaling
What is the operating voltage of LM293DGKR?
The LM293DGKR operates from a 2 V to 36 V supply. According to the Texas Instruments LM293 product page, this wide supply range allows the dual comparator to operate from low-voltage logic systems through industrial control rails. Differential input voltage can extend to ±38 V, subject to the device’s absolute maximum limits. The manufacturer identifies the LM293 as an industrial-grade dual differential comparator.
What are the key specifications of LM293DGKR that engineers should know?
The LM293DGKR is a dual differential comparator with a 2 V to 36 V supply range, 300 ns response time, open-collector outputs, and an 8-pin VSSOP package. Texas Instruments describes the LM293 family as compatible with TTL, MOS, and CMOS logic, with a common-mode input range extending to ground during single-supply operation. Its two channels are independent, and the operating temperature range is -40 C to +85 C.
Where to download the LM293DGKR datasheet PDF?
The official LM293 documentation is available through the Texas Instruments product page at https://www.ti.com/product/LM293. That page provides the manufacturer’s datasheet and ordering information for the LM293 family, including LM293DGKR. Use the manufacturer’s pin-description table and electrical-characteristics tables when assigning PCB signals and verifying absolute maximum ratings, response time, input offset, and output saturation.
Where can I find the LM293DGKR pinout?
The LM293DGKR pin assignment is documented in the Texas Instruments LM293 manufacturer datasheet linked from the official product page. The device uses an 8-pin VSSOP package containing two comparator channels, supply connections, ground connections, differential inputs, and open-collector outputs. Use the package drawing and pin-description table together to confirm exposed-pad requirements and the numbering orientation before laying out a PCB.
Can LM293DGKR use a pull-up resistor on its outputs?
Yes. Each LM293DGKR output is open collector and requires an external pull-up resistor for a valid high output level. The pull-up can connect to the supply used by the receiving logic, allowing the output voltage to match TTL, MOS, or CMOS requirements. The resistor must be selected to provide adequate rise time without excessive switching current, and separate pull-ups are needed when the two outputs operate independently.
Is LM293DGKR suitable for industrial voltage monitoring?
The LM293DGKR is suitable for industrial voltage monitoring within its specified operating limits. It provides two independent channels, a 2 V to 36 V supply range, a 300 ns response time, and an operating temperature range of -40 C to +85 C. The open-collector outputs support wired alarm or fault signals, while the differential inputs allow a monitored voltage to be compared against a reference.
What can replace LM293DGKR?
The closest same-family replacements are LM293ADGKRG4, LM393DGKR, LM2903DGKR, and LM193DGKR when their electrical ratings meet the design requirements. The LM293ADGKRG4 is listed in the same 8-pin VSSOP format and offers a different temperature-grade suffix. The LM393 and LM2903 families provide related dual-comparator functions, while LM193 is intended for a wider temperature range. Verify pin functions, supply limits, and input ratings before substitution.
Is LM293DGKR the same as LM293ADGKRG4?
No, LM293DGKR and LM293ADGKRG4 are not identical orderable versions. Both are Texas Instruments LM293-family dual comparators associated with the 8-pin VSSOP format, but the A suffix denotes a different temperature grade. LM293DGKR is associated with the -40 C to +85 C industrial range, while LM293ADGKRG4 is the wider-temperature variant. The distinction must be checked against the manufacturer ordering table.
When should I choose LM293DGKR over LM2903DGKR?
Choose LM293DGKR when the design specifically requires the LM293 family’s characterized operating behavior and an 8-pin VSSOP implementation. Choose LM2903DGKR only after confirming that its datasheet ratings meet the required supply, common-mode, offset, response-time, and output-current limits. Both are dual-comparator families, but package and family similarity alone does not guarantee identical electrical performance across temperature and production conditions.
Is LM293DGKR suitable for battery charger supervision?
The LM293DGKR can support battery or charger supervision when the sensed voltages remain within its input and supply limits. Its two channels can monitor separate thresholds, and the 300 ns response time allows rapid comparison of control signals. The open-collector output can drive a pull-up-backed fault indication, but the designer must confirm that reverse battery, load dump, and transient voltages remain inside the absolute maximum ratings.
LM293DGKR vs LM393DGKR - which is better for a control system?
LM293DGKR is preferable when the original system requirements are explicitly written around the LM293 family’s characterized behavior. LM393DGKR may be considered when its manufacturer specifications satisfy the required input offset, common-mode range, output saturation, supply range, and temperature limits. Both provide two comparator channels, but they are separate device families; confirm the exact pinout, performance, qualification, and lifecycle requirements rather than assuming interchangeability.
What is the best cross-brand equivalent for LM293DGKR?
No cross-brand equivalent is listed with enough package-specific and parametric detail to qualify as a confirmed drop-in replacement in the available manufacturer records. An equivalent dual comparator should use the same 8-pin VSSOP footprint, provide compatible input and output functions, support the required 2 V to 36 V supply range, and meet the application’s offset, response-time, common-mode, and temperature requirements. Request a quote for LM293DGKR when exact source continuity is preferred.
Where to buy LM293DGKR online?
Use the “Request a Quote” form on this page to request LM293DGKR from XAIPART. The form is the appropriate route for checking current availability, order quantities, and sourcing conditions for the exact 8-pin VSSOP orderable part. The manufacturer lists LM293 as an active family, but availability and lead time should be confirmed for the requested quantity and delivery schedule.
What is the price of LM293DGKR?
The current price of LM293DGKR is shown through the “Request a Quote” form on this page. Pricing can vary with order quantity, packaging, and supply conditions, so the form should be used for a current quotation rather than a static figure. The exact requested MPN is LM293DGKR, and the quote should identify the 8-pin VSSOP configuration to avoid package ambiguity.
What is the lead time and stock status for LM293DGKR?
Submit the “Request a Quote” form on this page to request the current lead time, minimum order quantity, and stock allocation for LM293DGKR. The manufacturer identifies the LM293 family as active, but a current production and distribution commitment depends on quantity, package, and delivery date. Providing the target quantity and required ship date enables a more useful sourcing response.

Data referensi kejuruteraan untuk LM293DGKR — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose LM293DGKR when the design calls for the LM293 family’s characterized dual-comparator behavior, a 2 V to 36 V supply range, open-collector outputs, and an 8-pin VSSOP footprint. Choose LM293ADGKRG4 when the same family and package are needed but operation down to -55 C is valuable. LM393DGKR and LM2903DGKR can be considered only when their individual offset, common-mode, temperature, and output specifications satisfy the application. LM193DGKR is appropriate when extended low-temperature operation justifies the wider temperature grade. No cross-brand drop-in candidate is confirmed here, so a second-source decision should be based on a package-specific comparison rather than the generic description “dual comparator.” For every choice, verify the pull-up voltage, sink current, input limits, supply current, and absolute maximum ratings.

Perbandingan dengan Gantian

Parametr Produk Ini LM293ADGKRG4 LM393DGKR LM2903DGKR LM193DGKR
Package 8-pin VSSOP 8-pin VSSOP 8-pin VSSOP 8-pin VSSOP 8-pin VSSOP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Comparator Type Dual differential comparator Dual general-purpose differential comparator Dual differential comparator Dual differential comparator Dual differential comparator
Number of Channels 2 channels 2 channels 2 channels 2 channels 2 channels
Supply Voltage Range 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V
Response Time 300 ns 300 ns 300 ns 300 ns 300 ns
Output Type Open-collector Open-collector Open-collector Open-collector Open-collector
Operating Temperature Range -40 C to +85 C -55 C to +125 C -40 C to +85 C -40 C to +85 C -55 C to +125 C

Penyeberangsung Jelas

  • Exact LM293 family continuity in an 8-pin VSSOP (vsLM393DGKR)
  • Industrial temperature range matched to standard equipment (vsLM193DGKR)
  • Dual open-collector channels in one compact package (vsLM2903DGKR)
  • 300 ns response for fast threshold decisions (vsLM293ADGKRG4)

Catatan Desain

Route the open-collector outputs away from sensitive input and reference nodes because the pull-up edge can produce fast voltage transitions. Keep the two differential input pairs close together and connect their ground returns through a low-impedance path. Place input filtering near the source when sensing noisy industrial signals, but ensure added capacitance does not upset the intended switching response or reference settling.

Do not operate an open-collector output without an external pull-up resistor; the output cannot reach a valid high level by itself. Select the pull-up from the receiver’s voltage requirement and the required edge rate. When tying both comparator outputs together for wired-OR operation, include the combined sink current in the calculation and confirm that the resulting common output polarity matches the downstream logic.

Check supply sequencing against every input voltage, including the ±38 V differential input limit. A comparator may remain within its supply range while an input transient exceeds the allowed differential or common-mode limit. Use series resistance, clamps, or filtering where long external wiring can introduce transients, and verify the configuration across both startup and shutdown rather than only during steady-state operation.

The LM293DGKR’s industrial -40 C to +85 C rating applies to the specified supply and electrical conditions. Place the 8-pin VSSOP on a PCB with adequate ground connectivity and avoid placing it beside a high-temperature regulator without thermal analysis. Since the device is primarily a low-power comparator, normal copper spreading is usually more relevant than a large external heatsink, but final thermal performance depends on the board and enclosure.

Maklumat Kesediaan

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Yes
Bosong halogen
Unknown
Mineral konflik
Unknown

RoHS-compliant and lead-free status is identified for LM293DGKR. Automotive qualification is not indicated for this industrial-grade orderable part.

Pencarian Berhubungan

LM293DGKR datasheet LM293DGKR pinout LM293DGKR datasheet pdf LM293DGKR equivalent LM293DGKR replacement LM293DGKR cross reference LM293DGKR vs LM393DGKR LM293DGKR footprint LM293DGKR spice model LM293DGKR price LM293DGKR stock Texas Instruments LM293DGKR LM293DGKR application circuit LM293DGKR 8 pin VSSOP LM293 dual differential comparator

Komponen dan Tanda berkaitan

Texas Instruments LM293DGKR LM293ADGKRG4 LM393DGKR LM2903DGKR LM193DGKR LM293 dual differential comparator voltage comparator interface IC analog semiconductor open-collector output open-drain output differential input common-mode voltage input offset voltage response time supply voltage 8-pin VSSOP VSSOP package family surface-mount package industrial-grade comparator TTL CMOS wired-OR logic RoHS
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ