LT1077CJ8 - Micropower Precision Op Amp | Analog Devices
MPN: LT1077CJ8 ✓ פעילLT1077CJ8 סקירה
An operational amplifier is an analog signal-processing IC that compares voltages applied to its inverting and non-inverting inputs and amplifies the difference between them. Precision operational amplifiers form part of the broader amplifier IC hierarchy and are commonly used in instrumentation, measurement, control, and sensor-conditioning circuits. The LT1077 specifically emphasizes low power consumption while retaining precision-oriented operation, making it useful where conventional precision amplifiers would consume too much supply current.
The LT1077's principal features include micropower operation, precision-amplifier architecture, compatibility with single 5 V supply conditions, specified operation under ±15 V conditions, and support for external offset-voltage nulling. The manufacturer identifies direct-replacement compatibility with the OP-07, OP-77, AD707, and LT1001, with supply-current reductions of 30 to 60 times. It is also a direct plug-in replacement for the LT1012 and OP-97, with approximately 10 times lower dissipation.
The technical compromise of this micropower design is important. The Analog Devices LT1077 datasheet states that competing micropower devices can seriously degrade precision, noise, speed, and output-drive specifications. Designers should therefore evaluate those parameters against the actual signal bandwidth, required noise performance, and load capability of the target circuit rather than selecting the amplifier solely from its low supply-current rating. The external nulling connection preserves compatibility with circuits using potentiometer-based offset adjustment.
Typical applications include battery-powered instrumentation, low-power sensor interfaces, portable measurement equipment, precision current-voltage conversion, and analog signal-conditioning stages that operate from a 5 V supply. In these systems, reduced supply current can extend operating time and reduce heat generation. The part can also be used where a previously installed OP-07-family circuit requires a lower-power replacement while retaining the established external offset-nulling arrangement.
PCB design should preserve the manufacturer's recommended bypassing arrangement and keep sensitive input and offset-null connections away from high-current switching paths. Because this is a ceramic dual-inline package, insertion and removal require care to avoid mechanical stress. Before substituting it into an existing design, confirm that the replacement amplifier's operating region, supply polarity, nulling method, and required stability behavior match the original circuit.
This page combines manufacturer-identified replacement relationships, package information, sourcing guidance, and practical migration considerations. It highlights where the LT1077CJ8 provides measurable supply-current or dissipation reductions and where precision, noise, speed, and output-drive requirements must be checked before it is used as a drop-in substitute.
חלופות תחליף ישיר עבור LT1077CJ8 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LT1077CJ8 (אותו גורם צורה וטביעת רגל) — שונים ב Amplifier Type, Mounting Type, Package.
LT1077IN8
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LT1077AMJ8
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
OP-07
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
OP-77
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
AD707
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LT1001CD
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LT1077CJ8 דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Micropower precision operational amplifier |
| Number of Circuits | 1 circuit |
| מארז | 8-pin CERDIP |
| Single-Supply Optimization | 5 V |
| Additional Supply Specification | ±15 V |
| Supply-Current Reduction versus OP-07, OP-77, AD707, and LT1001 | 30x to 60x lower supply current |
| Dissipation Reduction versus LT1012 and OP-97 | 10x lower dissipation |
| Offset Nulling | External potentiometer compatible |
| Direct-Replacement Devices | OP-07, OP-77, AD707, and LT1001 |
| Direct Plug-In Replacements | LT1012 and OP-97 |
| סוג הרכבה | Through-hole |
תצורת פינים של LT1077CJ8
| פין 1 | OFFSET NULL — External offset-voltage nulling connection |
| פין 2 | IN- — Inverting input |
| פין 3 | IN+ — Non-inverting input |
| פין 4 | V- — Negative supply connection |
| פין 5 | OFFSET NULL — External offset-voltage nulling connection |
| פין 6 | OUT — Amplifier output |
| פין 7 | V+ — Positive supply connection |
| פין 8 | NC — Not connected |
יישומים טיפוסיים
LT1077CJ8 מתאים עבור 6 יישוםs: Battery-Powered Precision Measurement, Low-Power Sensor Signal Conditioning, Portable Current-Voltage Instrumentation, Precision Control Loop Amplifier, Low-Power Data Acquisition Front End, Precision Reference Buffer.
Battery-Powered Precision Measurement
The LT1077CJ8 fits battery-powered measurement systems where a conventional precision amplifier would consume excessive supply current. Its micropower architecture is optimized for 5 V single-supply operation, and Analog Devices reports 30 to 60 times lower supply current than the OP-07, OP-77, AD707, and LT1001. Place the amplifier in the analog signal-conditioning path ahead of an ADC or display, retain the external offset-null arrangement used by the original precision-amplifier circuit, and verify the required noise, bandwidth, and output-drive levels. The principal benefit is longer operating time between battery replacements, although the system designer should still check offset error and signal settling against the measurement accuracy target.
מומלץ
Low-Power Sensor Signal Conditioning
The LT1077CJ8 is suitable for conditioning weak sensor signals in portable or energy-limited systems when low supply current is more important than maximum amplifier speed. Its 5 V single-supply optimization simplifies power allocation in sensor nodes, while the 30-to-60-times supply-current advantage over the OP-07 family can reduce system energy use. Use the amplifier with the same differential sensing topology and external offset-null method as the circuit being replaced. Check the input bias current, input voltage range, noise density, and settling time against the sensor output because the manufacturer notes that micropower operation can degrade precision, noise, speed, and output-drive specifications. This balance makes the device appropriate for controlled-bandwidth measurement channels rather than unrestricted high-frequency signal paths.
מומלץ
Portable Current-Voltage Instrumentation
The LT1077CJ8 can serve as the active element in portable current-to-voltage or differential measurement instrumentation designed around a 5 V rail. Its micropower operation helps limit battery drain, and its direct-replacement relationship with established precision amplifiers simplifies schematic review during design transitions. Configure the amplifier with the same external offset-nulling method used by the original circuit so board-level calibration procedures remain applicable. The design must confirm that the selected LT1077 variant provides adequate input bias current, offset voltage, noise, output swing, and output-drive performance for the transducer and ADC interface. Those checks are especially important because the LT1077 datasheet explicitly identifies degraded precision, noise, speed, and output drive as possible consequences of micropower operation.
מומלץ
Precision Control Loop Amplifier
The LT1077CJ8 is appropriate for precision control and feedback loops that operate at modest bandwidth and prioritize supply efficiency over high slew rate. Its 5 V optimization supports compact control systems, while external offset adjustment preserves the calibration behavior of common precision-amplifier layouts. Use the amplifier as a feedback element around the controlled plant and verify stability, output swing, and loop bandwidth against the manufacturer characteristics before deployment. The 30-to-60-times lower supply current relative to the OP-07, OP-77, AD707, and LT1001 can reduce thermal loading in compact equipment. If the loop requires rapid settling, high output current, or very low noise, compare those requirements carefully because the low-power architecture may not reproduce the performance of a conventional precision amplifier.
מומלץ
Low-Power Data Acquisition Front End
The LT1077CJ8 is useful in the analog front end of a low-power data-acquisition system that uses a 5 V supply. It can amplify a differential sensor or bridge signal before conversion, helping lower the power required by the analog channel when conventional precision amplifiers are unsuitable. Preserve the direct-replacement pin arrangement and external offset-trim pattern of the circuit being upgraded. Verify input common-mode range, output swing, noise, settling time, and drive capability for the selected ADC because the micropower tradeoff can affect dynamic performance. Compared with the OP-07-class devices named by Analog Devices, the LT1077 can reduce supply current by 30 to 60 times, potentially benefiting multi-channel systems in which every analog amplifier contributes to overall power consumption.
מומלץ
Precision Reference Buffer
The LT1077CJ8 can buffer a low-level reference or drive a precision analog node when the required bandwidth is modest and supply efficiency is important. Its micropower operation reduces the load presented by a 5 V system, and the compatibility with external offset nulling allows calibration practices associated with precision amplifiers to remain in place. Use suitable bypassing at the supply pins and keep the reference path short to avoid adding avoidable instability or noise. The engineer should confirm that the amplifier's input bias current does not disturb the reference source and that its output drive supports the downstream load. Its lower power consumption versus the OP-07, OP-77, AD707, and LT1001 is valuable, but low-noise and fast-settling applications still require a detailed comparison of the dynamic specifications.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LT1077CJ8 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LT1077IN8 | LT1077AMJ8 | OP-07 | OP-77 | AD707 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin CERDIP | 8-pin DIP | 8-pin CERDIP | 8-pin ceramic DIP option | 8-pin ceramic DIP option | 8-pin ceramic DIP option |
| Circuit Count | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Product Type | Micropower precision operational amplifier | Micropower precision operational amplifier | Micropower precision operational amplifier | Precision operational amplifier | Precision operational amplifier | Precision operational amplifier |
| External Offset Nulling | Supported | Supported | Supported | Supported | Supported | Supported |
| Supply-Current Advantage of LT1077 over Device | 30x to 60x lower than OP-07, OP-77, AD707, and LT1001 | Same LT1077 micropower approach | Same LT1077 micropower approach | Reference precision amplifier | Reference precision amplifier | Reference precision amplifier |
מבדילים עיקריים
- Major supply-current reduction over established precision amplifiers (לעומתOP-07)
- Micropower operation without abandoning precision-amplifier replacement (לעומתOP-77)
- Direct replacement path for AD707-based instrumentation (לעומתAD707)
הערות תכנון
Do not treat micropower operation as an unconditional substitute for a conventional precision amplifier. The Analog Devices LT1077 datasheet states that micropower performance can seriously degrade precision, noise, speed, and output drive. Before replacing an OP-07, OP-77, AD707, or LT1001, compare offset voltage, bias current, noise, gain-bandwidth product, slew rate, output swing, and drive capability with the original circuit requirements. Use external offset nulling as intended.
Estimate the expected supply-current benefit using the manufacturer's stated 30-to-60-times reduction relative to the OP-07, OP-77, AD707, and LT1001. Apply the selected comparison device's actual supply current and the required operating duty cycle to compare energy use. Also include output-load current and any always-on peripheral current in the calculation, since low amplifier supply current alone does not determine complete system consumption.
Reuse the original precision-amplifier pin arrangement only after confirming the exact package and pin functions. Keep the IN+ and IN- traces short, route offset-null connections away from switching nodes and high-current return paths, and place supply-bypass capacitors close to pins 4 and 7. For the ceramic DIP package, use appropriate insertion tooling and avoid lateral force on the leads to prevent package cracking.
Verify closed-loop stability and settling for the actual load, feedback network, and operating supply. Low power does not guarantee low distortion or fast settling, particularly when driving capacitive inputs or long interconnects. If the application is a precision measurement node, characterize noise and offset after replacement and preserve the original calibration sequence so drift can be separated from component substitution effects.
מידע על תאימות
The LT1077CJ8 is an analog operational amplifier rather than an automotive-qualified device, so AEC-Q100 is recorded as not applicable. No additional compliance conclusion is stated without a manufacturer declaration for this exact ordering code.