LT1223CJ8 - 100MHz Current Feedback Amplifier | Analog Devices
MPN: LT1223CJ8 ✓ פעילLT1223CJ8 סקירה
A current-feedback amplifier is a closed-loop amplifier topology that uses a feedback impedance to set gain rather than relying primarily on a closed-loop gain-bandwidth relationship. Within the LT1223CJ8, this architecture preserves useful bandwidth at higher closed-loop gains, unlike many conventional voltage-feedback operational amplifiers whose bandwidth falls rapidly as gain increases. The LT1223 family therefore remains useful in video, imaging, and communications designs where wide signal bandwidth must coexist with accurate analog gain.
The LT1223CJ8 provides 1000 V/µs slew rate, 50 mA output current, 6 mA quiescent current, and 5 MΩ input resistance. Its input offset voltage is 1 mV, input bias current is 1 µA, and settling time to 0.1% is 75 ns. These characteristics allow the amplifier to process rapidly changing signals while rejecting large common-mode inputs and driving analog signals over double-terminated cables.
The LT1223 uses a current-feedback architecture optimized for gain distribution through external feedback networks. Resistor selection directly influences gain, bandwidth, and stability, so the feedback and balancing networks should be implemented using the values and layout guidance in the manufacturer datasheet. Its wide supply range of ±15 V accommodates split analog rails commonly found in video and instrumentation systems.
Typical applications include video signal conditioning, cable-driver outputs, AGC and IF-chain amplification, test and measurement front ends, photodiode preamplification, and high-speed analog processing. The 50 mA output-drive capability is particularly useful when driving terminated transmission lines or downstream instrumentation stages, while the 100 MHz bandwidth supports video-bandwidth signals.
The principal design consideration is that current-feedback amplifiers are not interchangeable with conventional voltage-feedback amplifiers without checking stability and gain-network values. Place the feedback components close to the amplifier pins, follow the recommended reference resistor arrangement, and provide suitable bypass capacitance on both supply rails to minimize parasitic gain and preserve settling performance.
This page combines manufacturer-datasheet specifications, verified distributor listings, package information, practical high-speed layout guidance, and application-focused engineering context. It also records the absence of a verified pin-for-pin, same-package substitute so that engineers can evaluate lifecycle and sourcing decisions without relying on unverified cross-reference listings.
חלופות תחליף ישיר עבור LT1223CJ8 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
LT1223CN8
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
LT1223ACJ8
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
LT1223CJ8#PBF
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
LT1223CJ8 דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Current-feedback amplifier |
| Number of Circuits | 1 circuit |
| Gain Bandwidth Product | 100 MHz |
| Slew Rate | 1000 V/µs |
| Supply Voltage Range | ±15 V |
| Input Offset Voltage | 1 mV |
| Input Bias Current | 1 µA |
| Input Resistance | 5 MΩ |
| Settling Time | 75 ns to 0.1% |
| Output Current | 50 mA |
| זרם מנוחה | 6 mA |
| מארז | 8-lead CERDIP |
| סוג הרכבה | Through-hole |
| Temperature Grade | Commercial |
| Application Classification | Video amplifier |
| סטטוס RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
| Typical Gain-Bandwidth Behavior | High gain-bandwidth maintained at higher closed-loop gains |
תצורת פינים של LT1223CJ8
| פין 1 | OFFSET NULL — Offset-voltage null adjustment |
| פין 2 | INVERTING INPUT — Inverting amplifier input |
| פין 3 | NON-INVERTING INPUT — Non-inverting amplifier input |
| פין 4 | V- — Negative supply connection |
| פין 5 | OFFSET NULL — Offset-voltage null adjustment |
| פין 6 | OUTPUT — Amplifier output |
| פין 7 | V+ — Positive supply connection |
| פין 8 | NC — Not connected |
יישומים טיפוסיים
LT1223CJ8 מתאים עבור 6 יישוםs: Video Signal Conditioning, Double-Terminated Cable Driver, Photodiode Preamplification, Test and Measurement Front End, High-Speed Analog Processing, Industrial Control and Acquisition.
Video Signal Conditioning
The LT1223CJ8 fits video-signal conditioning stages that require wide bandwidth and fast settling. Its 100 MHz bandwidth supports video-bandwidth signals, while the 1000 V/µs slew rate preserves large-amplitude transitions with low distortion. The 50 mA output current provides useful drive for terminated video lines or subsequent amplifier stages. Use the manufacturer gain and balancing networks, place feedback components close to the device, and bypass the supply pins to limit parasitic gain. Compared with a conventional voltage-feedback amplifier, the LT1223 retains more useful bandwidth at higher closed-loop gains.
מומלץ
Double-Terminated Cable Driver
The LT1223CJ8 is suitable for driving analog signals over double-terminated cables because the manufacturer highlights its 100 MHz bandwidth, 1000 V/µs slew rate, and 50 mA output-current capability. The amplifier can sit at the end of a transmission line and develop the required output voltage into the characteristic impedance. Keep the output feedback loop compact and verify the output operating region against load impedance and supply voltage. Cable-driver use is a stronger fit than slow precision-amplifier implementations because slew rate and output drive determine large-signal fidelity.
מומלץ
Photodiode Preamplification
The LT1223CJ8 can serve in photodiode and optical-sensor preamplifier circuits where fast current pulses must be converted into a low-impedance voltage. Its 1 µA input bias current, 5 MΩ input resistance, and 75 ns settling time to 0.1% support accurate handling of weak sensor currents. The 1000 V/µs slew rate also helps reproduce short photodiode events. The transimpedance network must follow the manufacturer feedback arrangement, and the physical placement of the feedback resistor is critical for bandwidth and stability.
מומלץ
Test and Measurement Front End
The LT1223CJ8 is appropriate for instrumentation front ends that must preserve fast pulses or wideband AC signals. Its 100 MHz bandwidth and 75 ns settling time permit a measurement chain to capture short-duration events, while the 50 mA output drive can support cascaded stages and test fixtures. The device is especially useful where conventional voltage-feedback amplifiers would lose bandwidth at the required gain. Configure the gain network from the datasheet and keep input, feedback, and bypass connections short to minimize measurement errors and ringing.
מומלץ
High-Speed Analog Processing
The LT1223CJ8 supports general high-speed analog processing stages in which gain must remain effective at higher closed-loop settings. Its 100 MHz bandwidth and 1000 V/µs slew rate provide a combination suited to pulse conditioning, waveform shaping, and gain blocks. Unlike a general-purpose precision amplifier, the LT1223 is designed around current feedback and therefore requires its recommended external resistor network. Place the gain-setting components close to the amplifier and validate the complete layout with the intended source and load impedances.
מומלץ
Industrial Control and Acquisition
The LT1223CJ8 can be used in industrial control and data-acquisition systems where sensor or switching waveforms must be captured with limited distortion. Its fast slew rate reduces acquisition dead time, and the high bandwidth accommodates short control events. The 8-lead CERDIP through-hole package also suits ruggedized boards that use sockets or through-hole assembly methods. In such systems, confirm the commercial temperature grade against the ambient requirement, and observe the manufacturer guidance for supply bypassing and feedback stability.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LT1223CJ8 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Brand | Analog Devices |
| Package | 8-lead CERDIP, through-hole |
| Amplifier Type | Current-feedback amplifier |
| Number of Circuits | 1 circuit |
| Gain Bandwidth Product | 100 MHz |
| Slew Rate | 1000 V/µs |
| Supply Voltage Range | ±15 V |
| Input Offset Voltage | 1 mV |
| Input Bias Current | 1 µA |
| Settling Time | 75 ns to 0.1% |
| Output Current | 50 mA |
| Quiescent Current | 6 mA |
מבדילים עיקריים
- High bandwidth is retained at higher closed-loop gains (לעומתConventional voltage-feedback amplifiers)
- Substantial output drive for terminated analog lines (לעומתLow-power precision amplifiers)
- Fast settling complements wide bandwidth (לעומתGeneral-purpose wideband amplifiers)
הערות תכנון
Keep the LT1223CJ8 feedback, gain-setting, and balancing components close to the device, and minimize the loop area around the amplifier output and feedback node. Current-feedback amplifiers can tolerate much wider bandwidth than voltage-feedback amplifiers, but parasitic capacitance in the feedback network may still alter gain and stability. Follow the component placement and grounding pattern in the Analog Devices LT1223 datasheet rather than using a generic operational-amplifier layout.
Use the manufacturer gain-setting network as the design starting point because the feedback impedance directly determines the LT1223CJ8 bandwidth and stability. Check the closed-loop response with the actual source impedance, cable load, and probe capacitance. When driving a double-terminated line, confirm that the required output swing and 50 mA drive capability remain inside the amplifier's recommended operating region.
Place low-inductance bypass capacitors next to the positive and negative supply pins, and keep the return current through a low-impedance ground path. The device supports a ±15 V supply range according to the datasheet, but the exact operating range and permissible supply combinations should be checked in the manufacturer document before applying rail combinations. Add local filtering ahead of the amplifier when upstream switching converters create wideband supply noise.
מידע על תאימות
The verified product information identifies the LT1223CJ8 as a commercial-grade 8-lead CERDIP current-feedback amplifier but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this is a commercial analog amplifier rather than an automotive-qualified device.