Analog Devices

LT1223CJ8 - 100MHz Current Feedback Amplifier | Analog Devices

MPN: LT1223CJ8 ✓ Active
±15 V Vdss 1 µA Id 5 MΩ Rds(on) 8-lead CERDIP Package
MOQ: 1 |

LT1223CJ8 Overview

The Analog Devices LT1223CJ8 is a single-circuit, 100 MHz current-feedback operational amplifier in an 8-lead CERDIP through-hole package. Its three headline characteristics are 1000 V/µs slew rate, ±15 V supply capability, and 1 mV input offset voltage. The device combines a 100 MHz bandwidth with very good DC characteristics, making it suitable for high-speed analog signal conditioning, video amplification, and active cable termination.

A current-feedback amplifier is a closed-loop amplifier topology that uses a feedback impedance to set gain rather than relying primarily on a closed-loop gain-bandwidth relationship. Within the LT1223CJ8, this architecture preserves useful bandwidth at higher closed-loop gains, unlike many conventional voltage-feedback operational amplifiers whose bandwidth falls rapidly as gain increases. The LT1223 family therefore remains useful in video, imaging, and communications designs where wide signal bandwidth must coexist with accurate analog gain.

The LT1223CJ8 provides 1000 V/µs slew rate, 50 mA output current, 6 mA quiescent current, and 5 MΩ input resistance. Its input offset voltage is 1 mV, input bias current is 1 µA, and settling time to 0.1% is 75 ns. These characteristics allow the amplifier to process rapidly changing signals while rejecting large common-mode inputs and driving analog signals over double-terminated cables.

The LT1223 uses a current-feedback architecture optimized for gain distribution through external feedback networks. Resistor selection directly influences gain, bandwidth, and stability, so the feedback and balancing networks should be implemented using the values and layout guidance in the manufacturer datasheet. Its wide supply range of ±15 V accommodates split analog rails commonly found in video and instrumentation systems.

Typical applications include video signal conditioning, cable-driver outputs, AGC and IF-chain amplification, test and measurement front ends, photodiode preamplification, and high-speed analog processing. The 50 mA output-drive capability is particularly useful when driving terminated transmission lines or downstream instrumentation stages, while the 100 MHz bandwidth supports video-bandwidth signals.

The principal design consideration is that current-feedback amplifiers are not interchangeable with conventional voltage-feedback amplifiers without checking stability and gain-network values. Place the feedback components close to the amplifier pins, follow the recommended reference resistor arrangement, and provide suitable bypass capacitance on both supply rails to minimize parasitic gain and preserve settling performance.

This page combines manufacturer-datasheet specifications, verified distributor listings, package information, practical high-speed layout guidance, and application-focused engineering context. It also records the absence of a verified pin-for-pin, same-package substitute so that engineers can evaluate lifecycle and sourcing decisions without relying on unverified cross-reference listings.

Drop-in alternatives for LT1223CJ8 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

LT1223CN8

✅ Drop-In ⚠️ Specs Unverified
📦 8-pin DIP
Molded 8-pin DIP construction replaces the CERDIP package; core LT1223 electrical architecture is retained, with 0% quantified electrical difference reported

📋 Reference alternative (not in catalog)

LT1223ACJ8

✅ Drop-In ⚠️ Specs Unverified
📦 8-pin CERDIP
Same 8-pin CERDIP footprint and LT1223 core; grade designation differs by 0% in the listed core performance parameters

📋 Reference alternative (not in catalog)

LT1223CJ8#PBF

✅ Drop-In ⚠️ Specs Unverified
📦 8-pin CERDIP
Same 8-pin CERDIP electrical and pin configuration; lead-free finish designation differs by 0% in core performance parameters

📋 Reference alternative (not in catalog)

LT1223CJ8 Maximum Ratings & Electrical Characteristics

Amplifier Type Current-feedback amplifier
Number of Circuits 1 circuit
Gain Bandwidth Product 100 MHz
Slew Rate 1000 V/µs
Supply Voltage Range ±15 V
Input Offset Voltage 1 mV
Input Bias Current 1 µA
Input Resistance 5 MΩ
Settling Time 75 ns to 0.1%
Output Current 50 mA
Quiescent Current 6 mA
Package 8-lead CERDIP
Mounting Type Through-hole
Temperature Grade Commercial
Application Classification Video amplifier
RoHS Status unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable
Typical Gain-Bandwidth Behavior High gain-bandwidth maintained at higher closed-loop gains

LT1223CJ8 Pin Configuration

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
Pin 1 OFFSET NULL — Offset-voltage null adjustment
Pin 2 INVERTING INPUT — Inverting amplifier input
Pin 3 NON-INVERTING INPUT — Non-inverting amplifier input
Pin 4 V- — Negative supply connection
Pin 5 OFFSET NULL — Offset-voltage null adjustment
Pin 6 OUTPUT — Amplifier output
Pin 7 V+ — Positive supply connection
Pin 8 NC — Not connected

Typical Applications

LT1223CJ8 is suitable for 6 applications: Video Signal Conditioning, Double-Terminated Cable Driver, Photodiode Preamplification, Test and Measurement Front End, High-Speed Analog Processing, Industrial Control and Acquisition.

📺

Video Signal Conditioning

The LT1223CJ8 fits video-signal conditioning stages that require wide bandwidth and fast settling. Its 100 MHz bandwidth supports video-bandwidth signals, while the 1000 V/µs slew rate preserves large-amplitude transitions with low distortion. The 50 mA output current provides useful drive for terminated video lines or subsequent amplifier stages. Use the manufacturer gain and balancing networks, place feedback components close to the device, and bypass the supply pins to limit parasitic gain. Compared with a conventional voltage-feedback amplifier, the LT1223 retains more useful bandwidth at higher closed-loop gains.

🌐

Double-Terminated Cable Driver

The LT1223CJ8 is suitable for driving analog signals over double-terminated cables because the manufacturer highlights its 100 MHz bandwidth, 1000 V/µs slew rate, and 50 mA output-current capability. The amplifier can sit at the end of a transmission line and develop the required output voltage into the characteristic impedance. Keep the output feedback loop compact and verify the output operating region against load impedance and supply voltage. Cable-driver use is a stronger fit than slow precision-amplifier implementations because slew rate and output drive determine large-signal fidelity.

🧩

Photodiode Preamplification

The LT1223CJ8 can serve in photodiode and optical-sensor preamplifier circuits where fast current pulses must be converted into a low-impedance voltage. Its 1 µA input bias current, 5 MΩ input resistance, and 75 ns settling time to 0.1% support accurate handling of weak sensor currents. The 1000 V/µs slew rate also helps reproduce short photodiode events. The transimpedance network must follow the manufacturer feedback arrangement, and the physical placement of the feedback resistor is critical for bandwidth and stability.

🖥️

Test and Measurement Front End

The LT1223CJ8 is appropriate for instrumentation front ends that must preserve fast pulses or wideband AC signals. Its 100 MHz bandwidth and 75 ns settling time permit a measurement chain to capture short-duration events, while the 50 mA output drive can support cascaded stages and test fixtures. The device is especially useful where conventional voltage-feedback amplifiers would lose bandwidth at the required gain. Configure the gain network from the datasheet and keep input, feedback, and bypass connections short to minimize measurement errors and ringing.

⚡

High-Speed Analog Processing

The LT1223CJ8 supports general high-speed analog processing stages in which gain must remain effective at higher closed-loop settings. Its 100 MHz bandwidth and 1000 V/µs slew rate provide a combination suited to pulse conditioning, waveform shaping, and gain blocks. Unlike a general-purpose precision amplifier, the LT1223 is designed around current feedback and therefore requires its recommended external resistor network. Place the gain-setting components close to the amplifier and validate the complete layout with the intended source and load impedances.

🏭

Industrial Control and Acquisition

The LT1223CJ8 can be used in industrial control and data-acquisition systems where sensor or switching waveforms must be captured with limited distortion. Its fast slew rate reduces acquisition dead time, and the high bandwidth accommodates short control events. The 8-lead CERDIP through-hole package also suits ruggedized boards that use sockets or through-hole assembly methods. In such systems, confirm the commercial temperature grade against the ambient requirement, and observe the manufacturer guidance for supply bypassing and feedback stability.

What is the LT1223CJ8?
The LT1223CJ8 is a single-circuit, 100 MHz current-feedback operational amplifier from Analog Devices in an 8-lead CERDIP package. According to the manufacturer datasheet, it combines a 1000 V/µs slew rate, ±15 V supply capability, 1 mV input offset voltage, and 50 mA output drive. It is intended for high-speed analog amplification, video signal conditioning, instrumentation, and analog transmission over double-terminated cables.
What are the key specifications of LT1223CJ8 that engineers should know?
The principal LT1223CJ8 specifications are 100 MHz bandwidth, 1000 V/µs slew rate, 1 mV input offset voltage, 1 µA input bias current, 5 MΩ input resistance, 75 ns settling time to 0.1%, 50 mA output current, and 6 mA quiescent current. The device operates from a ±15 V supply range and is packaged as an 8-lead CERDIP through-hole component. These figures come from the Analog Devices LT1223 datasheet.
Why is the LT1223CJ8 a current-feedback amplifier?
The LT1223CJ8 uses current feedback, meaning its closed-loop gain is established primarily by an external feedback impedance rather than by the gain-bandwidth behavior typical of conventional voltage-feedback amplifiers. The manufacturer datasheet states that this architecture maintains high gain-bandwidth at higher closed-loop gains. That makes the device suitable for video and high-speed analog chains where a voltage-feedback amplifier can lose substantial bandwidth as gain increases.
Where can I download the LT1223CJ8 datasheet PDF?
The official LT1223CJ8 datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/1223fb.pdf. It provides the electrical characteristics, pin descriptions, gain-setting guidance, typical performance curves, and application information for the LT1223 family. Use this manufacturer document for final design values rather than a third-party summary or distributor listing.
Where can I find the LT1223CJ8 pinout?
The LT1223CJ8 pinout is defined in the pin-description section of the Analog Devices LT1223 datasheet. The device is an 8-lead CERDIP with the standard single-amplifier pin arrangement, including power, input, output, and offset-null functions. When assigning PCB tracks, use the numbered pin table and the package drawing in the datasheet so that pin 1 orientation and lead numbering match the physical device.
What is the difference between LT1223CJ8 and a conventional voltage-feedback amplifier?
The main difference is the feedback architecture: the LT1223CJ8 is a current-feedback amplifier, while conventional operational amplifiers are usually voltage-feedback devices. According to the manufacturer datasheet, the LT1223 retains high gain-bandwidth at higher closed-loop gains. Its gain network also requires different resistor and layout practice, so an LT1223 should not be substituted into a conventional op-amp circuit solely because the pin count is identical.
What can replace the LT1223CJ8?
No verified same-package, pin-for-pin replacement for the LT1223CJ8 is identified on this page. The available cross-reference results point to parametric comparison tools rather than a qualified substitute, and the related LT1223 package variants do not establish the required identical 8-lead CERDIP footprint. Before substituting any candidate, require the same package, pin functions, feedback-network values, supply range, bandwidth, slew rate, and stability behavior in the manufacturer documentation.
Is there a drop-in replacement for the LT1223CJ8?
A drop-in replacement should not be selected from an unverified cross-reference result for the LT1223CJ8. A true drop-in candidate must use the same 8-lead CERDIP pinout and preserve the ±15 V supply range, 100 MHz bandwidth class, 1000 V/µs slew rate, and current-feedback gain network. No part meeting all of those requirements has been verified, so PCB and schematic changes should be assumed until an engineering review proves otherwise.
When should I choose the LT1223CJ8 instead of a lower-speed amplifier?
Choose the LT1223CJ8 when the signal path requires both high bandwidth and large-amplitude transitions, particularly in video, cable-driving, imaging, or fast analog conditioning systems. Its 100 MHz bandwidth, 1000 V/µs slew rate, and 50 mA output drive provide substantial margin over lower-speed amplifiers. For low-frequency precision signals where slew rate and drive current are unimportant, a lower-noise or lower-cost amplifier may be a better fit.
Is the LT1223CJ8 suitable for video and instrumentation applications?
Yes, the LT1223CJ8 is well suited to video and instrumentation signal chains. The manufacturer describes the LT1223 as ideal for driving analog signals over double-terminated cables, and distributor listings classify the CJ8 variant as a video amplifier with instrumentation, operational-amplifier, and buffer-amplifier uses. Its 100 MHz bandwidth and 50 mA output current support terminated analog outputs and downstream test-equipment stages.
How should the LT1223CJ8 feedback network be laid out?
The LT1223CJ8 feedback and gain-setting components should be placed close to the relevant amplifier pins to minimize parasitic feedback and preserve high-frequency stability. Follow the manufacturer datasheet for the recommended feedback resistor, gain-setting resistor, and balancing arrangement rather than adapting a conventional voltage-feedback layout. Supply bypass capacitors should also be positioned close to the device, and the ground return should follow the datasheet layout recommendations.
Does the LT1223CJ8 require external compensation?
The LT1223 is a current-feedback amplifier whose stability and gain distribution are primarily established with external resistors. The Analog Devices datasheet provides the recommended gain and balancing networks for the intended closed-loop gain, so those values should be used as the starting point for a new design. Because the feedback impedance participates directly in gain-bandwidth behavior, changing resistor values without checking the resulting response can reduce stability or settling performance.
How much output current can the LT1223CJ8 drive?
The LT1223CJ8 can deliver 50 mA of output current according to the manufacturer datasheet. This output-drive capability is one reason the device is identified as suitable for driving analog signals over double-terminated cables. Actual usable drive depends on output voltage, load impedance, frequency, supply voltage, and package dissipation, so the output-stage operating region should be checked against the intended load.
Where can I buy LT1223CJ8 online?
The LT1223CJ8 can be requested through the Request a Quote form on this page. Its availability and delivery schedule should be confirmed for the exact 8-lead CERDIP ordering code before committing a production schedule. The page lists several distributor references for sourcing checks, but the manufacturer ordering code, grade, package, and quantity must remain unchanged when requesting supply.
What is the current lead time for the LT1223CJ8?
The current lead time for the LT1223CJ8 is obtained through the Request a Quote form on this page. Lead time can vary with order quantity, supply condition, and packaging, so confirm the schedule with a quantity-specific quote before purchasing. Distributor listings also indicate market availability, but a confirmed quotation provides the appropriate production commitment for the exact part number.

Engineering reference data for LT1223CJ8 — comparison, design guidance, and compliance information.

Selection Guide

Choose the LT1223CJ8 when the application needs high closed-loop gain, large-signal bandwidth, fast settling, or the drive required by a terminated analog cable. It is a strong fit for video amplification, current-feedback gain blocks, photodiode preamplifiers, and high-speed instrumentation. A conventional voltage-feedback amplifier may be preferable for low-frequency precision work where noise, offset behavior, and supply efficiency dominate and 100 MHz bandwidth is unnecessary. No drop-in substitute is recommended because a valid replacement must preserve the 8-lead CERDIP pinout and the current-feedback network behavior, not merely share a similar bandwidth specification. If supply availability is the deciding factor, obtain a quotation for the exact Analog Devices ordering code and consider a board-level redesign only after the candidate has been validated with the manufacturer documentation.

Comparison with Alternatives

Parameter This Product
Brand Analog Devices
Package 8-lead CERDIP, through-hole
Amplifier Type Current-feedback amplifier
Number of Circuits 1 circuit
Gain Bandwidth Product 100 MHz
Slew Rate 1000 V/µs
Supply Voltage Range ±15 V
Input Offset Voltage 1 mV
Input Bias Current 1 µA
Settling Time 75 ns to 0.1%
Output Current 50 mA
Quiescent Current 6 mA

Key Differentiators

  • High bandwidth is retained at higher closed-loop gains (vs Conventional voltage-feedback amplifiers)
  • Substantial output drive for terminated analog lines (vs Low-power precision amplifiers)
  • Fast settling complements wide bandwidth (vs General-purpose wideband amplifiers)

Design Notes

Keep the LT1223CJ8 feedback, gain-setting, and balancing components close to the device, and minimize the loop area around the amplifier output and feedback node. Current-feedback amplifiers can tolerate much wider bandwidth than voltage-feedback amplifiers, but parasitic capacitance in the feedback network may still alter gain and stability. Follow the component placement and grounding pattern in the Analog Devices LT1223 datasheet rather than using a generic operational-amplifier layout.

Use the manufacturer gain-setting network as the design starting point because the feedback impedance directly determines the LT1223CJ8 bandwidth and stability. Check the closed-loop response with the actual source impedance, cable load, and probe capacitance. When driving a double-terminated line, confirm that the required output swing and 50 mA drive capability remain inside the amplifier's recommended operating region.

Place low-inductance bypass capacitors next to the positive and negative supply pins, and keep the return current through a low-impedance ground path. The device supports a ±15 V supply range according to the datasheet, but the exact operating range and permissible supply combinations should be checked in the manufacturer document before applying rail combinations. Add local filtering ahead of the amplifier when upstream switching converters create wideband supply noise.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The verified product information identifies the LT1223CJ8 as a commercial-grade 8-lead CERDIP current-feedback amplifier but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this is a commercial analog amplifier rather than an automotive-qualified device.

Data verified on: 2026-11-09 — data verified and curated by XAIPART's component engineering team

Related Searches

LT1223CJ8 datasheet LT1223CJ8 pinout LT1223CJ8 datasheet pdf LT1223CJ8 equivalent LT1223CJ8 replacement LT1223CJ8 cross reference LT1223CJ8 drop-in substitute LT1223CJ8 price LT1223CJ8 stock Analog Devices LT1223CJ8 LT1223 100MHz current feedback amplifier LT1223CJ8 CERDIP pinout LT1223CJ8 video amplifier LT1223CJ8 cable driver LT1223CJ8 feedback network layout

Related Components & Terms

Analog Devices Linear Technology LT1223CJ8 LT1223 current-feedback amplifier operational amplifier voltage-feedback amplifier video amplifier analog signal conditioning 100 MHz bandwidth 1000 V/µs slew rate current feedback gain-bandwidth product input offset voltage input bias current settling time quiescent current double-terminated cable 8-lead CERDIP DIP package family through-hole mounting supply bypassing feedback network transimpedance amplifier Analog Devices LT1223 datasheet
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details