LTC1050CH - 0.5 uV Zero-Drift Op Amp | Analog Devices
MPN: LTC1050CH ✓ פעילLTC1050CH סקירה
A zero-drift operational amplifier is a chopper-stabilized amplifier whose input offset voltage and related drift are periodically corrected to reduce low-frequency error. These amplifiers are used when slow changes in the input would create unacceptable measurement error. The LTC1050 belongs to the operational-amplifier hierarchy and ultimately falls within the broader category of analog signal-chain ICs used for amplification, buffering, instrumentation, feedback, and precision analog processing.
The principal advantage of the LTC1050CH is its combination of 0.5 uV input offset voltage and 10 pA input bias current. Integrating the two sample-and-hold capacitors on chip reduces the external component count normally associated with chopper-stabilized amplifiers. The CH ordering code identifies the industrial-temperature, wired-lead TO-5 package, while the underlying LTC1050 family is also offered in other package formats. Its zero-drift architecture is particularly relevant to low-frequency sensor signals where offset drift can dominate the useful measurement.
Unlike a conventional precision bipolar amplifier whose offset changes continuously with temperature and aging, the LTC1050 periodically corrects its offset to suppress very-low-frequency error. This chopping architecture can introduce ripple and broadband-noise effects, so system-level noise and bandwidth must be evaluated with the manufacturer application guidance. Input and output filtering, grounding, lead arrangement, and supply bypassing remain important when the amplifier operates near its input-offset or noise limits.
Typical uses include precision bridge and thermocouple amplifiers, low-level current measurement, strain-gauge signal conditioning, laboratory instrumentation, and slow sensor systems where input voltage changes are small relative to the signal of interest. The 10 pA input bias current is particularly useful with high-impedance sources, while the 0.5 uV offset supports measurements in which microvolt-level errors would otherwise consume a meaningful portion of the signal. The TO-5 metal-can package also provides a mechanically robust through-hole format for instrumentation equipment.
When designing around the LTC1050CH, use the manufacturer pin-description table for the 8-terminal TO-5 connection and preserve the specified package orientation. Place supply-bypass capacitors close to the device, use short feedback paths, and keep high-impedance input traces away from switching nodes. Confirm the final noise bandwidth and chopping-related ripple with the application circuit rather than relying only on the low DC offset specification.
This page combines the device identity, package information, manufacturer application resources, replacement guidance, and practical design considerations for engineers evaluating the LTC1050CH. The comparison information focuses on drop-in compatibility, while the application notes explain how zero-drift performance, input bias current, internal capacitors, and the TO-5 mechanical format affect instrumentation design.
חלופות תחליף ישיר עבור LTC1050CH — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
אין חלופות תואמות Drop-in עבור מוצר זה.
בקשת חלופותLTC1050CH דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Precision zero-drift operational amplifier |
| טופולוגיה | Chopper-stabilized |
| Number of Circuits | 1 circuit |
| Input Offset Voltage | 0.5 uV |
| Input Bias Current | 10 pA |
| Internal Sample-and-Hold Capacitors | 2 integrated capacitors |
| מארז | TO-5 metal can |
| Package Shape | Round |
| Terminal Form | Wire |
| Number of Terminals | 8 |
| Temperature Grade | Industrial |
| סוג הרכבה | Through-hole |
| סטטוס מחזור חיים | Production |
מדריך תצורת פינים של LTC1050CH round
תצורת פינים עבור LTC1050CH (מארזת round). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור LTC1050CH.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
LTC1050CH מתאים עבור 6 יישוםs: Precision Bridge Measurement, Thermocouple Signal Conditioning, High-Impedance Current Sensing, Strain-Gauge Instrumentation, Laboratory Measurement Equipment, Precision Sensor Interfaces.
Precision Bridge Measurement
The LTC1050CH is suitable for low-level bridge-amplifier input stages where its 0.5 uV input offset voltage limits static signal error and its 10 pA input bias current reduces disturbance of high-impedance sensor nodes. The chopper-stabilized architecture is valuable when the bridge output changes slowly and ordinary amplifier offset drift would obscure the measurement. The two integrated sample-and-hold capacitors reduce external conditioning circuitry, while the TO-5 metal-can package provides a robust through-hole implementation. Designers should still verify common-mode range, input bias behavior with the selected sensor, and chopping ripple across the intended measurement bandwidth.
Thermocouple Signal Conditioning
The LTC1050CH can serve as the input amplifier for low-level thermocouple signals because a 0.5 uV offset specification is appropriate when the measured temperature corresponds to only a small differential voltage. Its 10 pA input bias current is especially helpful when long thermocouple wiring raises the effective source impedance and creates leakage-related errors. The integrated internal capacitors simplify the chopper-stabilized input stage compared with conventional designs requiring external sampling components. Practical use still requires input protection, proper input filtering, careful cold-junction compensation, and verification that the operating temperature and common-mode requirements fit the measurement system.
High-Impedance Current Sensing
The LTC1050CH fits low-level current measurement when the shunt or sensor output presents a high source impedance to the amplifier. Its specified 10 pA input bias current minimizes the bias-dependent voltage error that can obscure nanoamp-class or highly resistive signals, while the 0.5 uV offset reduces residual voltage error at the amplifier input. The device should be placed close to the sensing element to minimize leakage and capacitive pickup. Application engineering must confirm input common-mode limits, account for the amplifier's noise and chopping behavior, and ensure that the TO-5 wiring does not add excessive thermocouple or thermoelectric error.
Strain-Gauge Instrumentation
For strain-gauge and piezoelectric-adjacent measurement systems, the LTC1050CH offers a low-offset input stage with 10 pA bias current and two integrated sample-and-hold capacitors. These characteristics are useful for slow mechanical measurements where the bridge output is small and temperature-dependent offset drift could dominate the result. The 8-terminal TO-5 package is mechanically suitable for through-hole instrumentation boards and can simplify hand-built or legacy-style analog modules. Designers should define the required noise bandwidth, assess aliasing around the chopper correction frequency, and apply guarding or shielding when source impedance is high enough for leakage to matter.
Laboratory Measurement Equipment
The LTC1050CH can improve the input stage of laboratory instruments that measure millivolts or microvolts from resistive, capacitive, or electrochemical sensors. The 0.5 uV offset reduces calibration burden when the useful signal is only slightly larger than the input error, while the 10 pA bias current protects measurements made through high-value source resistances. Its integrated chopper capacitors make the amplifier suitable for precision DC signal conditioning without reproducing the external sample-and-hold arrangement associated with many conventional chopper amplifiers. The system designer should still characterize chopping ripple, noise density, settling behavior, and input bias variation over the complete temperature range.
Precision Sensor Interfaces
The LTC1050CH is appropriate for precision sensor interfaces that combine slow signal variation with high source impedance. Its 0.5 uV offset minimizes static error at the input, and its 10 pA bias current reduces loading of the sensor. Because the amplifier is chopper-stabilized, the output must be filtered according to the required control bandwidth, and the correction spectrum must not be confused with the low-frequency drift it suppresses. The robust 8-terminal TO-5 construction is useful in industrial analog modules where a through-hole mechanical format is preferred over a fine-pitch surface-mount package.
נתוני עזר הנדסיים עבור LTC1050CH — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Brand | Analog Devices |
| Package | 8-terminal TO-5 metal can |
| Mounting Type | Through-hole |
| Temperature Grade | Industrial |
| Amplifier Architecture | Precision zero-drift chopper-stabilized operational amplifier |
| Number of Circuits | 1 circuit |
| Input Offset Voltage | 0.5 uV |
| Input Bias Current | 10 pA |
| Internal Sample-and-Hold Capacitors | 2 integrated capacitors |
| Number of Terminals | 8 |
מבדילים עיקריים
- Very low input offset for precision DC instrumentation (לעומתLTC1050 family options in SO-8 and dual-in-line packages)
- Reduced external chopper-conditioning circuitry (לעומתConventional chopper-stabilized operational amplifiers requiring external sampling capacitors)
- Low input bias current for high-impedance sensing (לעומתConventional precision bipolar operational amplifiers)
הערות תכנון
Keep high-impedance input and feedback routes short and away from switching or high-current traces. The LTC1050CH's 10 pA input bias current is valuable for high-source-impedance measurements, but board leakage, contaminated insulation, and nearby digital activity can still dominate the error. Use guarding where appropriate and verify the complete assembled system rather than relying only on the device's input-bias specification.
Follow the manufacturer datasheet pinout and package orientation for the 8-terminal TO-5 connection. Place supply-bypass components close to the relevant device terminals, maintain a low-impedance ground return, and keep the feedback loop compact. Because the TO-5 device uses through-hole leads, pay particular attention to lead resistance and thermally induced junctions in precision measurement boards.
Do not judge the LTC1050CH only by its 0.5 uV DC offset specification. Chopper-stabilized amplifiers can produce correction-spectrum components, and the usable bandwidth depends on the required signal bandwidth and output filtering. Establish the required noise and settling limits, simulate the complete filter, and verify operation across input range, load, supply, and temperature before releasing the design.
מידע על תאימות
The LTC1050 is a production precision operational amplifier, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration appears in the available manufacturer and distributor information. AEC-Q100 qualification is not applicable to this industrial TO-5 device based on the listed industrial temperature grade.