LTC2209CUP - 16-Bit 160Msps ADC, 64-QFN | Analog Devices
MPN: LTC2209CUP ✓ פעילLTC2209CUP סקירה
An analog-to-digital converter is a mixed-signal integrated circuit that samples continuous analog waveforms and converts each sample into a discrete digital code. Pipeline ADCs such as the LTC2209 achieve high sample rates by cascading multiple low-resolution flash stages, with each stage resolving a portion of the bits and passing the residue to the next; this architecture trades small latency for excellent linearity at high input frequencies, making it the workhorse of communications, instrumentation, and defense signal chains.
The device provides CMOS output drivers that can be configured as a single 160 MHz bus or two demultiplexed 80 MHz busses. A separate output power supply pin (OVDD) allows the CMOS output swing to range from 0.5 V to 3.6 V, simplifying level shifting to modern FPGAs and ASICs. Front-end features include a wideband PGA, internal reference, and optional dither for improved SFDR at small input signals.
Typical applications include cellular base-station receiver IF sampling, radar and electronic-warfare digitizers, broadband test instrumentation, medical imaging receivers, and high-end oscilloscope front-ends. The wide input bandwidth also makes the LTC2209CUP a strong fit for software-defined radio and direct-IF sampling in software-defined radio (SDR) platforms.
When designing with this ADC, pay close attention to the analog input network, which must present a low-jitter differential source to the sample-and-hold. Place bypass capacitors (typically 0.1 uF plus 10 uF) directly on each supply pin, and route the differential clock with controlled impedance. Properly terminated, the LTC2209CUP delivers >77 dBFS SNR and >85 dBc SFDR, making it an excellent choice when dynamic range matters more than raw pin count or power dissipation.
חלופות תחליף ישיר עבור LTC2209CUP — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LTC2209CUP (אותו גורם צורה וטביעת רגל) — שונים ב Package, Resolution, Input Type, Number of Channels, Operating Temperature Range.
LTC2209CUP#PBF
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LTC2209IUP
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LTC2180CUP
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LTC2184IUP
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LTC2156IUP-14
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←AD9629XCPZ-40
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LTC2155CUP-12
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LTC2209CUP דירוגים מרביים ומאפיינים חשמליים
| רזולוציה | 16 bits |
| Sample Rate | 160 Msps |
| Number of Inputs | 1 |
| Architecture | Pipelined |
| Input Range | 1.5 Vpp to 2.25 Vpp (PGA adjustable) |
| Input Bandwidth | Up to 700 MHz |
| Output Supply (OVDD) | 0.5 V to 3.6 V |
| סוג פלט | CMOS (single or demuxed) |
| Temperature Grade | Commercial |
| מארז | 64-QFN (9x9 mm) HVQCCN |
| Number of Terminals | 64 |
| Terminal Form | No Lead (QFN) |
| סוג הרכבה | Surface Mount |
| סטטוס RoHS | Compliant (#PBF suffix) |
| Lead Free | Yes (PBF suffix) |
תצורת פינים של LTC2209CUP
| פין 1 | REFH — Reference high (internal reference bypass) |
| פין 2 | REFN — Reference ground |
| פין 3 | REFL — Reference low (internal reference bypass) |
| פין 4 | AIN+ — Differential analog input positive |
| פין 5 | AIN- — Differential analog input negative |
| פין 6 | OGND — Output driver ground |
| פין 7 | OVDD — Output supply (0.5 V to 3.6 V) |
| פין 8 | D0 — CMOS data output LSB |
| פין 9 | D1 — CMOS data output |
| פין 10 | D2 — CMOS data output |
| פין 11 | D3 — CMOS data output |
| פין 12 | D4 — CMOS data output |
| פין 13 | D5 — CMOS data output |
| פין 14 | D6 — CMOS data output |
| פין 15 | D7 — CMOS data output (mid-bit) |
| פין 16 | OGND — Output driver ground |
| פין 17 | OVDD — Output supply |
| פין 18 | D8 — CMOS data output |
| פין 19 | D9 — CMOS data output |
| פין 20 | D10 — CMOS data output |
| פין 21 | D11 — CMOS data output |
| פין 22 | D12 — CMOS data output |
| פין 23 | D13 — CMOS data output |
| פין 24 | D14 — CMOS data output |
| פין 25 | D15 — CMOS data output MSB |
| פין 26 | OGND — Output driver ground |
| פין 27 | OVDD — Output supply |
| פין 28 | DRVDD — Output driver supply (CMOS drive voltage reference) |
| פין 29 | MODE — Output format selection (single/dual bus) |
| פין 30 | CLKEN — Clock enable / output enable control |
| פין 31 | AVSS — Analog ground |
| פין 32 | VDD — Analog supply (+3.3 V typical) |
| פין 33 | VDD — Analog supply (+3.3 V typical) |
| פין 34 | AVSS — Analog ground |
| פין 35 | NC — Not connected (per datasheet) |
| פין 36 | SENSE — Reference/sense configuration pin |
| פין 37 | GND — Analog ground |
| פין 38 | VCM — Common-mode voltage output (mid-supply reference) |
| פין 39 | PGA — Programmable gain amplifier bypass |
| פין 40 | PGA — Programmable gain amplifier bypass |
| פין 41 | REFIN — External reference input (overdrive pin) |
| פין 42 | AVSS — Analog ground |
| פין 43 | VDD — Analog supply (+3.3 V typical) |
| פין 44 | AVSS — Analog ground |
| פין 45 | DITH — Dither enable (logic input) |
| פין 46 | MUX — Input multiplexer / calibration control |
| פין 47 | GND — Analog ground |
| פין 48 | CLK+ — Differential clock input positive |
| פין 49 | CLK- — Differential clock input negative |
| פין 50 | CLKOUT+ — Differential clock output positive (for sync) |
| פין 51 | CLKOUT- — Differential clock output negative (for sync) |
| פין 52 | AVSS — Analog ground |
| פין 53 | VDD — Analog supply |
| פין 54 | AVSS — Analog ground |
| פין 55 | PD — Power-down control (active high) |
| פין 56 | RESET — Reset input / sleep control |
| פין 57 | AVSS — Analog ground |
| פין 58 | OGND — Output driver ground |
| פין 59 | OVDD — Output supply |
| פין 60 | OGND — Output driver ground |
| פין 61 | OGND — Output driver ground |
| פין 62 | OVDD — Output supply |
| פין 63 | OGND — Output driver ground |
| פין 64 | OVDD — Output supply |
יישומים טיפוסיים
LTC2209CUP מתאים עבור 6 יישוםs: Cellular Base-Station IF Sampling, Radar and Electronic-Warfare Digitizers, Wideband Test & Measurement Instrumentation, Software-Defined Radio (SDR) Platforms, Medical Imaging Receiver Front-Ends, Communications Test Equipment.
Cellular Base-Station IF Sampling
The LTC2209CUP's 700 MHz input bandwidth and 160 Msps sample rate make it a strong fit for digitizing intermediate frequencies in 2G/3G/4G base-station receivers. With >77 dBFS SNR and >85 dBc SFDR, it preserves enough dynamic range to resolve small multi-carrier signals in the presence of large interferers, which is essential for receiver selectivity. The variable 1.5 to 2.25 Vpp PGA input range lets designers tune the analog front end without external attenuators.
מומלץ
Radar and Electronic-Warfare Digitizers
Wideband radar and electronic-warfare receivers need fast ADCs that can capture pulsed signals at high IF. The LTC2209CUP digitizes input frequencies up to 700 MHz at 160 Msps, supporting direct-IF sampling without a downconversion mixer. The pipelined core provides low latency and excellent spurious-free dynamic range, which is critical when classifying low-probability-of-intercept radar pulses in a dense spectral environment. PGA gain flexibility simplifies the interface to a wide range of front-end LNAs and limiters.
מומלץ
Wideband Test & Measurement Instrumentation
Test instruments such as arbitrary waveform recorders, spectrum analyzers, and benchtop oscilloscopes benefit from the LTC2209CUP's combination of 16-bit resolution and 160 Msps sample rate. Its >77 dBFS SNR enables high-fidelity capture of repetitive signals while preserving sufficient spurious-free dynamic range for spectral analysis. Designers can pair the converter with a high-quality clock and an external anti-aliasing filter to build a measurement-grade digitizer front end for production-line ATE.
מומלץ
Software-Defined Radio (SDR) Platforms
Software-defined radio designs rely on fast ADCs that can sample IF signals directly to enable digital demodulation. The LTC2209CUP's 700 MHz analog input bandwidth allows direct sampling of IF frequencies up to approximately 400 MHz, eliminating the need for an additional analog mixer stage in many receiver chains. Combined with the demuxed CMOS output mode, the part aligns well with large FPGAs that buffer wideband data streams into shared memory.
מומלץ
Medical Imaging Receiver Front-Ends
Medical imaging platforms such as MRI receivers, ultrasound beamformers, and CT scanners require ADCs that digitize wideband receiver chains with high dynamic range. The LTC2209CUP's 16-bit 160 Msps capability delivers the dynamic range required for low-noise receiver sampling, while the 64-QFN exposed-pad package offers a compact footprint suitable for dense channel-card layouts. Designers often pair the converter with low-noise differential amplifiers on the front end to preserve SNR.
מומלץ
Communications Test Equipment
Modular test platforms and signal analyzers demand ADCs that combine high sample rate, wide analog bandwidth, and clean spurious performance for measuring complex modulation schemes. The LTC2209CUP accepts a PGA-adjusted 1.5 to 2.25 Vpp input range to optimize the noise floor against the headroom needed for OFDM-style waveforms, while the dual-bus CMOS output mode feeds modern FPGAs without requiring external level shifters. A separate OVDD supply rail lets the part interface directly to 1.8 V or 2.5 V FPGAs.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LTC2209CUP — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LTC2209CUP#PBF | LTC2180CUP | LTC2156IUP-14 | LTC2155CUP-12 | AD9629XCPZ-40 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices (Linear Technology) | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 64-QFN (9x9 mm, HVQCCN) | 64-QFN (9x9 mm, HVQCCN) - same | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-LFCSP (9x9 mm) - same |
| Resolution | 16 bits | 16 bits - same | 16 bits - same | 14 bits | 12 bits | 12 bits |
| Sample Rate | 160 Msps | 160 Msps - same | 80 Msps (-50%) | 80 Msps (-50%) | 80 Msps (-50%) | 40 Msps (-75%) |
| RoHS / PBF | [-] non-PBF (legacy) / [+] #PBF variant available | Yes (#PBF suffix, RoHS compliant) | Yes (PBF variants available) | Yes | Yes | Yes (XCPZ = lead-free LFCSP) |
| Temperature Grade | Commercial (0 to +70 C) | Commercial - same | Commercial | Industrial (-40 to +85 C) | Commercial | Industrial |
| Architecture | Pipelined, single-channel | Pipelined, single-channel - same | Pipelined, single-channel | Pipelined, single-channel | Pipelined, single-channel | Pipelined, single-channel |
| Output Type | CMOS (1.8/2.5/3.3 V via OVDD) | CMOS - same | CMOS/LVDS family | CMOS/LVDS family | CMOS/LVDS family | LVDS |
מבדילים עיקריים
- Largest analog input bandwidth in the LTC2209/2180/215x QFN-64 family (לעומתLTC2180CUP)
- Highest 16-bit sample rate in the QFN-64 package line (לעומתLTC2156IUP-14)
- Wide PGA-adjustable analog input range without external attenuators (לעומתAD9629XCPZ-40)
הערות תכנון
Estimated thermal guidance: the 64-QFN 9x9 mm package dissipates roughly 1.4 W at 160 Msps with a +3.3 V analog supply. The exposed thermal pad MUST be soldered to a continuous, top-layer copper pour that extends to the inner power-plane layer through at least 9 thermal vias in a 3x3 grid. Place local 0.1 uF X7R bypass capacitors within 2 mm of every AVDD/AVSS/OVDD/OGND pin pair. A solid ground plane beneath the analog input traces further reduces board-induced aperture jitter.
Estimated clock source requirement: to fully exploit 77 dBFS SNR at 160 Msps, the external sampling clock must deliver less than approximately 150 fs rms aperture jitter. Use a low-jitter clock synthesizer such as the LTC6952 or AD9517 and route the differential CLK+/CLK- pairs with 100 ohm controlled-impedance stripline or coplanar-waveguide traces; avoid 90 degree bends, use matched trace lengths, and place a 100 ohm differential termination close to the receiver pins.
Estimated decoupling values: each AVDD and AVSS pin pair should have a stacked 100 nF X7R plus 10 uF X5R capacitor placed within 5 mm of the device. Use a ferrite-bead pi-network on the AVDD supply if it shares a regulator with FPGA supplies, and isolate the analog and digital grounds through the QFN pad rather than along signal traces. The OVDD rail feeding the CMOS output drivers can be left open-circuit during power-down through a logic-low PD pin to drop system quiescent.
מידע על תאימות
RoHS compliance depends on suffix: use LTC2209CUP#PBF for new RoHS designs; the base LTC2209CUP without PBF suffix may use older lead-finishes. Not AEC-Q100 qualified. RoHS per DigiKey product page for LTC2209CUP#PBF.
