Analog Devices

LTC486ISW - Quad RS485 Driver, 5V, 16-SOIC | Analog Devices

MPN: LTC486ISW ✓ פעיל
5 V Vdss 110 µA Id RS485 and RS422 Rds(on) 16-pin SOIC (SOL-16) Package
כמות הזמנה מינימלית: 1 |

LTC486ISW סקירה

Analog Devices LTC486ISW is a quad low-power differential bus and line driver designed for RS485 and RS422 multipoint data transmission. The device operates from a single 5 V supply, supports a bus common-mode range from -7 V to +12 V, and is packaged in a 16-pin SOIC. Each channel provides differential driver outputs with three-state operation for shared-bus systems.

An RS485 driver is a physical-layer interface component that converts a digital logic signal into a balanced differential signal suitable for reliable communication over long or electrically noisy cables. It belongs to the interface IC hierarchy, alongside RS422 line drivers, transceivers, and isolators. Balanced differential signaling improves common-mode noise rejection and enables multiple devices to share a bus when their outputs are tri-stated.

The LTC486 uses a low-power CMOS implementation with a typical supply current of 110 µA. It meets RS485 and RS422 applications, supports extended common-mode operation, and provides three-state outputs for multipoint networks. Its ruggedness against overload and electrostatic-discharge damage makes it suitable for industrial equipment where driver outputs may encounter noisy or fault-prone bus wiring.

The four independent channels reduce the component count on systems that require multiple communication links, instrumentation buses, or distributed I/O. Thermal shutdown protects the device if an output is accidentally shorted to a supply or low-impedance source. Depending on the fault condition, the manufacturer notes that up to 250 mA can flow through the affected output before shutdown behavior intervenes.

Typical uses include industrial measurement systems, instrumentation buses, data acquisition equipment, factory automation interfaces, and embedded control systems. The LTC486 is especially useful where multiple nodes must share one bus and only one transmitter should be active at a time. Its extended common-mode range can improve interoperability in systems using longer cables or grounds at different potentials.

PCB design should keep the driver close to the bus connector, provide a solid ground-plane connection, and include appropriate protection against external transients. Verify output rise and fall times, bus loading, cable length, termination, and grounding before treating a laboratory connection as production-ready. The 16-pin SOIC also leaves adequate board area for routing and surge-protection components.

This product page combines the LTC486 family specifications with orderable package information, focused application guidance, design checks, and verified same-footprint alternatives. It helps engineers distinguish the basic LTC486ISW ordering code from lead-free and tape-and-reel production variants without overlooking common-mode, thermal, and bus-integration constraints.

חלופות תחליף ישיר עבור LTC486ISW — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

LTC486ISW#PBF

✅ Drop-In
📦 SOIC-16 (SOL-16)
Lead-free ordering designation for the same LTC486 family; electrical ratings are unchanged, while procurement markings differ by 0%.

📋 חלופה להתייחסות (לא בקטלוג)

LTC486ISW מפרטים

Device Type Quad differential bus/line driver
Supported Standards RS485 and RS422
Number of Drivers 4 channels
מתח אספקה 5 V
Typical Supply Current 110 µA
Common-Mode Range -7 V to +12 V
Output State Control Three-state outputs
Technology CMOS
טמפרטורת פעולה -40 °C to +85 °C
מארז 16-pin SOIC (SOL-16)
מספר פינים 16 pins
סוג הרכבה Surface mount
Thermal Shutdown Temperature 150 °C
Maximum Fault Current per Output Up to 250 mA
Overload and ESD Ruggedness Designed for overload and ESD damage resistance

מדריך תצורת פינים של LTC486ISW 16-pin soic (sol-16)

תצורת פינים עבור LTC486ISW (מארזת 16-pin soic (sol-16)). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.

תרשים פינים של מארזת 16-pin soic (sol-16) עבור LTC486ISW

אין נתוני פריסת פינים מפורטים עבור LTC486ISW.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

LTC486ISW מתאים עבור 6 יישוםs: Industrial Instrumentation Bus, Data Acquisition Equipment, Factory Automation Control, Building and HVAC Networks, Remote Sensor Interface, Embedded Communication Gateway.

🏭

Industrial Instrumentation Bus

The LTC486ISW fits industrial instrumentation buses that require multiple differential driver channels from one 5 V interface circuit. Its four channels can connect separate nodes to a shared RS485 pair, while three-state control prevents simultaneous active drivers from fighting each other. The manufacturer-rated -7 V to +12 V common-mode range provides additional tolerance for ground-potential differences across a multi-node installation. With a typical supply current of 110 µA, the device also suits distributed field equipment where long idle periods make supply efficiency important. The design should still include connector-level surge protection, controlled grounding, and logic timing that disables all but the intended bus transmitter.

📊

Data Acquisition Equipment

The LTC486ISW is suitable for laboratory and process data-acquisition equipment that must place control or measurement information onto an RS485 or RS422 network. Four differential driver channels allow one package to support several bus segments, reducing board area compared with separate single-channel drivers. The 5 V supply operation integrates naturally with modern mixed-signal equipment, while the CMOS implementation provides a typical supply current of 110 µA. For reliable acquisition systems, use separate driver and receiver circuitry where full duplex is required, and verify that each cable, terminator, and grounding arrangement is compatible with the intended RS485 topology.

🤖

Factory Automation Control

The LTC486ISW supports factory automation interfaces where controllers, sensors, remote I/O modules, and operator panels communicate over a multipoint bus. Four independently enabled channels can serve multiple cable ports or support bus segmentation, and the three-state outputs allow inactive channels to release the bus. Its -40 °C to +85 °C operating range covers industrial environments, while overload resistance and thermal shutdown help manage accidental output faults. A production design should add appropriate transient protection at exposed connectors because the IC's internal ruggedness does not determine the surge withstand rating of the complete interface path.

🏢

Building and HVAC Networks

The LTC486ISW can be used in building-control and HVAC equipment for reliable communication with distributed sensors, actuators, and supervisory controllers. RS485 differential signaling suits longer cable runs and installations where electrical noise is present, while the extended common-mode range helps accommodate potential differences between powered nodes. Four channels provide flexibility when a controller must communicate with several bus segments or isolated device groups. Because HVAC equipment may experience temperature changes and wiring faults, maintain the specified -40 °C to +85 °C range and use thermal shutdown as a secondary protection layer rather than the sole safeguard against a shorted bus.

🧩

Remote Sensor Interface

The LTC486ISW is appropriate for remote sensor interfaces that transmit commands or collected information over an RS485 network. Its low typical supply current of 110 µA helps limit consumption in remotely powered or duty-cycled equipment, and the three-state outputs support multiple nodes attached to the same bus when only one is transmitting. The -7 V to +12 V common-mode capability offers useful margin where the sensor ground and controller ground are not identical. Engineering validation should include cable-length and capacitance checks, termination at the physical ends of the bus, and verification that the chosen protection components preserve the driver's intended signaling behavior.

🖥️

Embedded Communication Gateway

The LTC486ISW suits embedded gateways that bridge processor-based systems to legacy RS485 or RS422 equipment. Four driver channels can support multiple external buses without allocating a separate package for every port, and operation from a single 5 V rail simplifies integration with digital controllers. The low-power CMOS design is particularly helpful in compact gateways where standby consumption matters. Layout should keep the SOIC close to the external connector, route differential outputs as a tightly coupled pair, and provide a direct return-path connection to the connector ground. Firmware must also enforce exclusive bus enable timing so that two nodes cannot drive the network simultaneously.

סיכום מוצרים מומלצים

LTC486ISW#PBF Lead-free ordering option for production assembly בשימוש ב-: Industrial Instrumentation Bus, Data Acquisition Equipment, Factory Automation Control, Building and HVAC Networks, Remote Sensor Interface, Embedded Communication Gateway
What is the LTC486ISW?
The LTC486ISW is a quad low-power differential bus and line driver for RS485 and RS422 interfaces. According to the Analog Devices LTC486 manufacturer datasheet, it uses a single 5 V supply, provides four independently controlled differential drivers, and supports an extended bus common-mode range from -7 V to +12 V. The device is offered in a 16-pin SOIC package for conventional surface-mount PCB assembly.
What are the key specifications of LTC486ISW that engineers should know?
The LTC486ISW combines four RS485/RS422 driver channels, a 5 V supply, three-state outputs, and a -7 V to +12 V common-mode range in a 16-pin SOIC. According to the Analog Devices LTC486 manufacturer datasheet, typical supply current is 110 µA and thermal shutdown occurs at 150 °C. The outputs are designed to withstand overload and ESD conditions encountered in industrial communication systems.
How many RS485 drivers does LTC486ISW contain?
The LTC486ISW contains four differential driver channels. This allows one IC to serve several independent communication links or to support a multipoint bus with several driver outputs connected to the same conductors. According to the Analog Devices LTC486 manufacturer datasheet, the outputs use three-state operation so that only the intended transmitter should be enabled when multiple nodes share a bus.
What is the common-mode voltage range of LTC486ISW?
The LTC486ISW supports an extended common-mode range from -7 V to +12 V. According to the Analog Devices LTC486 manufacturer datasheet, this range allows the device to operate on RS485 buses where the receiver-side ground potential can differ from the driver ground. The operating limits should still be checked against the complete bus network, cable arrangement, and protection components used in the final system.
Is LTC486ISW suitable for RS422 applications?
Yes, the LTC486ISW is suitable for both RS485 and RS422 communication systems. According to the Analog Devices LTC486 manufacturer datasheet, it is a differential line driver intended for multipoint data transmission and explicitly meets RS422 requirements. RS485 designs should use the enable control to prevent multiple nodes from driving a shared bus simultaneously, while RS422 point-to-point links can use the individual channel outputs.
Where can I download the LTC486ISW datasheet PDF?
The official LTC486ISW datasheet PDF is available from Analog Devices at the LTC486 technical-documentation URL listed on this page. It describes the quad low-power RS485/RS422 driver, electrical characteristics, pin functions, three-state behavior, thermal shutdown, and application information. Use the manufacturer PDF for final pin assignments, timing limits, recommended operating conditions, and footprint dimensions before releasing a PCB layout.
Where can I find the LTC486ISW pinout?
Use the pin-description table and package drawing in the official Analog Devices LTC486 manufacturer datasheet to locate the LTC486ISW pinout. The component is a 16-pin SOIC, but its physical lead numbering and function names must be assigned directly from that document rather than inferred from another quad-driver family. The package drawing is also required to confirm the PCB land pattern and pin-1 orientation.
What can replace LTC486ISW?
LTC486ISW#PBF is the verified same-brand, same-footprint lead-free ordering option for the LTC486ISW, and it is the closest supported drop-in choice identified for this product. The Analog Devices manufacturer page and component listings identify both orderings as LTC486 variants. Before substitution, verify that enable timing, output impedance, bus loading, temperature grade, and package dimensions satisfy the original design requirements.
Is LTC486ISW the same as LTC486ISW#PBF?
LTC486ISW#PBF identifies the lead-free production ordering of the same Analog Devices LTC486 family device, while LTC486ISW is the base ordering designation used in the product title. The manufacturer product listing and distributor records associate both with the quad low-power RS485/RS422 driver family. Procurement documents should state the complete orderable code, and engineers should confirm the associated temperature and reel-handling suffix before release.
When should I choose LTC486ISW over another quad RS485 driver?
Choose the LTC486ISW when a design needs four RS485/RS422 driver channels, three-state outputs, a single 5 V supply, and an extended -7 V to +12 V common-mode range. According to the Analog Devices LTC486 manufacturer datasheet, its typical supply current is 110 µA and its CMOS construction emphasizes low power. Choose a different family only after comparing driver impedance, propagation delay, bus capacitance, protection requirements, and exact pin assignments.
Is LTC486ISW suitable for industrial instrumentation buses?
The LTC486ISW is suitable for many industrial instrumentation and multipoint bus designs. Its four differential driver channels, three-state outputs, extended common-mode range, overload protection, and -40 °C to +85 °C operating range align with demanding cable-connected equipment. The Analog Devices LTC486 manufacturer datasheet also documents thermal shutdown at 150 °C, adding protection for accidental output shorts.
How much power does LTC486ISW dissipate?
The LTC486ISW supply consumption is characterized by a typical 110 µA current at 5 V, as stated in the Analog Devices LTC486 manufacturer datasheet. At that typical operating point, the estimated supply power is 5 V × 110 µA = 550 µW. Actual dissipation can increase with output switching activity, external load, and fault current, so a designer should evaluate the highest expected operating condition rather than relying only on the typical figure.
Does LTC486ISW protect against shorted outputs?
Yes, the LTC486ISW includes thermal shutdown for excessive internal power dissipation caused by an output shorted to a supply or low-impedance source. According to the Analog Devices LTC486 manufacturer datasheet, up to 250 mA can flow through the affected output under such a fault condition, and shutdown occurs when the internal temperature reaches 150 °C. External protection and cable design remain necessary because internal shutdown is not a substitute for a correctly coordinated fault-current strategy.
What is the lifecycle status of LTC486ISW?
The LTC486ISW remains listed as an Analog Devices product with an active manufacturer product page and current distributor records. The family is also offered under the lead-free LTC486ISW#PBF ordering code and a tape-and-reel LTC486ISW#TR ordering code. For a production release, request the current lifecycle, traceability, and assembly-status confirmation associated with the exact orderable suffix.
Where to buy LTC486ISW online and what is the price?
Use the Request a Quote form on this page to request LTC486ISW pricing, current stock, minimum order quantity, and lead time. The form is the correct route for a transaction that depends on the exact suffix, including tape-and-reel or lead-free ordering. Do not substitute a family-level starting price for a firm quote because quantity breaks, date code, packaging, and sourcing conditions can change the commercial result.
What is the lead time for LTC486ISW?
The current lead time for LTC486ISW depends on the complete orderable suffix, quantity, packaging, and date-code requirement. Submit the Request a Quote form on this page with the target quantity and whether the assembly uses LTC486ISW, LTC486ISW#PBF, or LTC486ISW#TR. This allows the request to be evaluated as an exact production line item rather than as a generic LTC486 family inquiry.

נתוני עזר הנדסיים עבור LTC486ISW — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the LTC486ISW when the design needs four low-power differential driver channels for RS485 or RS422 communication, particularly in multipoint industrial systems that require three-state bus control. Its 5 V operation, 110 µA typical supply current, -7 V to +12 V common-mode range, and -40 °C to +85 °C temperature rating make it appropriate for instrumentation, automation, building-control, and embedded gateway equipment. Use LTC486ISW#PBF when the procurement specification requires the manufacturer’s lead-free ordering designation; it preserves the same electrical function and SOIC-16 footprint. For a different quad-driver family, compare pin assignments carefully rather than assuming protocol compatibility guarantees pin compatibility. Pay particular attention to output impedance, propagation delay, bus-capacitance limits, enable polarity, thermal performance, and package dimensions. If the existing design requires full-duplex transceivers rather than transmit-only drivers, select a transceiver architecture instead of using four isolated driver channels.

השוואה עם חלופות

פרמטר מוצר זה LTC486ISW#PBF
Brand Analog Devices Analog Devices
Package SOIC-16 (SOL-16) SOIC-16 (SOL-16), same footprint
Device Type Quad differential bus/line driver Quad differential bus/line driver
Supported Standards RS485 and RS422 RS485 and RS422
Number of Drivers 4 channels 4 channels
Supply Voltage 5 V 5 V
Typical Supply Current 110 µA 110 µA
Common-Mode Range -7 V to +12 V -7 V to +12 V
Output Control Three-state outputs Three-state outputs
Operating Temperature -40 °C to +85 °C -40 °C to +85 °C

מבדילים עיקריים

  • Four-channel differential driver integration (לעומתA single-channel RS485 driver)
  • Extended RS485 common-mode range (לעומתA conventional limited common-mode RS485 driver)
  • Low-power CMOS implementation (לעומתA typical bipolar RS485 line driver)

הערות תכנון

Route each differential driver output as a tightly coupled pair from the LTC486ISW to the connector. Keep the pair geometry consistent and avoid splitting its return path, because mismatched impedances can degrade signal integrity and increase radiated emissions. Place the IC near the connector and place protection devices close to the entry point. Maintain a continuous ground reference beneath the interface area and avoid sharing narrow return-current paths with high-current switching stages.

Do not enable more than one driver on the same RS485 bus segment at a time. The LTC486ISW provides three-state outputs for multipoint communication, but the firmware or hardware control logic must prevent overlapping enable intervals. Review propagation delay and enable timing from the manufacturer datasheet, include suitable holding time around disable, and test every power-up, reset, and fault-recovery sequence for bus contention.

Calculate the worst-case driver dissipation rather than relying only on the 110 µA typical supply current. A shorted output can draw up to 250 mA according to the Analog Devices LTC486 manufacturer datasheet, and thermal shutdown engages at 150 °C. Use the datasheet electrical limits for worst-case design calculations, provide connector protection where necessary, and ensure that the exposed copper and surrounding airflow can dissipate normal switching and fault-related heat.

Confirm the complete orderable suffix before releasing production documents. LTC486ISW, LTC486ISW#PBF, and LTC486ISW#TR identify different purchasing or packaging conditions for the LTC486 family. Use the manufacturer ordering guide to confirm temperature grade, lead-free status, shipping format, and quantity limits. A component marked with a functionally similar family name is not automatically approved for substitution without a complete electrical, timing, pinout, and footprint review.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The verified product information identifies LTC486ISW#PBF as a lead-free ordering designation, but the manufacturer pages do not explicitly state the compliance status of the base LTC486ISW ordering code. RoHS, REACH, AEC-Q100, halogen-free, and conflict-minerals status therefore remain unconfirmed.

הנתונים אומתו בתאריך: 2026-11-09 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

LTC486ISW datasheet LTC486ISW datasheet pdf LTC486ISW pinout LTC486ISW equivalent LTC486ISW replacement LTC486ISW cross reference LTC486ISW price LTC486ISW stock LTC486ISW#PBF Analog Devices LTC486ISW LTC486ISW RS485 driver LTC486ISW SOIC-16 footprint LTC486ISW industrial bus LTC486ISW common mode range

רכיבים ומונחים קשורים

Analog Devices Linear Technology LTC486ISW LTC486ISW#PBF LTC486ISW#TR RS485 RS422 quad differential bus driver quad line driver interface IC multipoint data transmission three-state output CMOS common-mode range 5 V supply 110 µA supply current thermal shutdown 150 °C shutdown SOIC-16 SOL-16 surface-mount package industrial instrumentation factory automation data acquisition remote sensor interface embedded communication gateway
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר