MAX232ECDWR - Dual 250kbps RS-232 Transceiver | Texas Instruments
MPN: MAX232ECDWR ✓ פעילMAX232ECDWR סקירה
An RS-232 transceiver is an interface IC that converts between single-ended TTL and CMOS logic levels and the differential, bipolar signaling used by RS-232 equipment. Its transmitters provide level shifting and signal conditioning for outgoing data, while its receivers translate incoming RS-232 signals into logic-compatible levels. The MAX232ECDWR combines two transmitters and two receivers in one package, making it suitable for two-way serial links in industrial control, instrumentation, data acquisition, and legacy peripheral equipment.
Key electrical characteristics include operation from a 4.5V to 5.5V single supply and a maximum signaling rate of 250kbps. IEC 61000-4-2 protection is a distinguishing feature for cables and connectors that may be exposed to electrostatic discharge. The 16-pin SOIC package follows the familiar MAX232E pin arrangement, including dedicated charge-pump capacitor pins and a bypass-capacitor connection. These external capacitors must be selected according to the manufacturer datasheet rather than substituted with arbitrary values.
The MAX232E architecture uses a capacitive voltage generator to produce the positive and negative voltage levels required for RS-232 transmission. Because this charge-pump architecture needs external capacitors, board layout should keep the charge-pump network compact and place bypass capacitance close to the supply pins. The receiver side converts bipolar RS-232 input levels to CMOS logic levels, allowing the device to interface directly with a host UART or other digital controller.
Typical applications include RS-232 ports on industrial test equipment, programmable logic controllers, serial adapters, point-of-sale terminals, laboratory instruments, and embedded control boards. The 250kbps rate is suitable for legacy serial peripherals, configuration links, and short-distance point-to-point communication. The integrated ESD protection is particularly useful where an exposed DB9 or equivalent connector connects the transceiver to external cables.
When designing the board, verify the required charge-pump and bypass capacitor values in the manufacturer datasheet and confirm that the 4.5V to 5.5V supply remains within tolerance during transients. Keep protected connector-side routing separated from sensitive logic-side traces, and provide a controlled ground reference between communicating systems to avoid unintended signal offsets.
This page combines the exact MAX232ECDWR ordering information, electrical characteristics, cross-reference findings, PCB implementation guidance, and application-specific engineering guidance for engineers evaluating the SOIC-16 transceiver for RS-232 interfaces.
חלופות תחליף ישיר עבור MAX232ECDWR — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MAX232ECDWR (אותו גורם צורה וטביעת רגל) — שונים ב Package, Product Type, Maximum Data Rate, Supply Voltage, Interface Standard.
MAX232EIDWR
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←MAX3232EIDR
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←MAX232EIDR
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←TRS232EIDWR
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX3232ECDR
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←MAX232ECDWR מפרטים
| Product Type | Dual RS-232 driver/receiver |
| Number of Transmitters | 2 |
| Number of Receivers | 2 |
| Maximum Data Rate | 250 kbps |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Supply Type | Single 5 V supply |
| ESD Protection Standard | IEC 61000-4-2 |
| מארז | 16-pin SOIC (DW), 0.295 inch / 7.50 mm width |
| סוג הרכבה | Surface mount |
| Transmitter Output Type | RS-232 line driver |
| Receiver Output Type | TTL/CMOS logic-level receiver |
| Charge-Pump Architecture | Capacitive voltage generator with external capacitors |
| Number of External Charge-Pump Capacitors | 4 |
| Bypass Capacitor Connection | 1 external capacitor pin |
תצורת פינים של MAX232ECDWR
| פין 1 | V+ — Positive charge-pump output |
| פין 2 | R1OUT — Receiver 1 output |
| פין 3 | R2OUT — Receiver 2 output |
| פין 4 | R2IN — Receiver 2 input |
| פין 5 | R1IN — Receiver 1 input |
| פין 6 | GND — Ground |
| פין 7 | V- — Negative charge-pump output |
| פין 8 | T2IN — Transmitter 2 input |
| פין 9 | T2OUT — Transmitter 2 output |
| פין 10 | T1IN — Transmitter 1 input |
| פין 11 | T1OUT — Transmitter 1 output |
| פין 12 | VCC — Positive supply |
| פין 13 | V+ — Positive charge-pump output |
| פין 14 | C3 — Charge-pump capacitor connection |
| פין 15 | C2 — Charge-pump capacitor connection |
| פין 16 | C1 — Charge-pump and bypass capacitor connection |
יישומים טיפוסיים
MAX232ECDWR מתאים עבור 6 יישוםs: Industrial Test and Measurement Equipment, Programmable Logic Controller Serial Ports, Embedded UART and USB-to-Serial Adapters, Point-of-Sale and Service Terminal Interfaces, Laboratory Data Acquisition Systems, Legacy Peripheral and Printer Connectivity.
Industrial Test and Measurement Equipment
The MAX232ECDWR fits legacy RS-232 control and data ports on oscilloscopes, programmable power supplies, and laboratory instruments. Its two transmitters and two receivers support full-duplex communication at rates up to 250kbps, while the 4.5V to 5.5V supply range matches common 5V instrument-control logic. IEC 61000-4-2 protection is especially valuable when users connect a DB9 cable directly to the instrument. Place the charge-pump capacitors close to their pins and route connector-side traces away from sensitive measurement circuitry.
מומלץ
Programmable Logic Controller Serial Ports
The MAX232ECDWR provides the physical layer for a two-wire RS-232 service port on a programmable logic controller or industrial controller. The 250kbps maximum rate supports parameter downloads, diagnostic messages, and configuration transfers to legacy peripherals. Two drivers and two receivers allow independent command and telemetry paths within one 16-pin SOIC. The integrated IEC 61000-4-2 protection improves robustness at an externally accessible connector, although chassis grounding and enclosure design remain essential for industrial surge and ESD control.
מומלץ
Embedded UART and USB-to-Serial Adapters
The MAX232ECDWR is useful in embedded boards that expose an RS-232 connector to a host UART, modem, or service interface. It translates 5V logic signals into RS-232 levels and returns received data as CMOS-compatible logic, avoiding a separate line-driver circuit. Its 250kbps rate suits configuration and diagnostic traffic rather than high-bandwidth data transfer. Keep the external charge-pump network compact, provide local supply bypassing, and place protection or filtering components close to the connector entry point.
מומלץ
Point-of-Sale and Service Terminal Interfaces
The MAX232ECDWR can support a legacy RS-232 connection between a point-of-sale terminal, printer, scanner, or service console and a controller board. Its dual-driver, dual-receiver configuration supports both outbound commands and inbound status or receipt data at rates up to 250kbps. ESD protection is beneficial in retail equipment where the serial port may be connected during installation or servicing. The 16-pin SOIC footprint keeps the interface compact, while the datasheet-specified capacitor values should be used unchanged to maintain reliable charge-pump operation.
מומלץ
Laboratory Data Acquisition Systems
The MAX232ECDWR suits laboratory data-acquisition systems that retain a serial console for configuration, calibration, and diagnostics. At 250kbps, the link is appropriate for command traffic and periodic status transfer rather than continuous high-rate sample streaming. The receiver converts incoming RS-232 levels to logic signals for the controller, and the transmitters return acknowledgements or control data. IEC 61000-4-2 protection adds value for bench equipment where the serial connector is accessible to operators and connected cables may be handled frequently.
מומלץ
Legacy Peripheral and Printer Connectivity
The MAX232ECDWR enables a modern controller to communicate with legacy RS-232 printers, scales, scanners, and service interfaces that have no USB or network port. The 250kbps limit comfortably covers typical printer-control and receipt-transfer traffic while the 4.5V to 5.5V operating range integrates directly with 5V digital systems. Two channels can handle independent data and flow-control signals when required. Maintain a defined signal-ground reference between connected systems and avoid long unprotected stubs away from the connector-side protection circuitry.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MAX232ECDWR — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MAX232EIDWR | MAX3232EIDR | MAX232EIDR | TRS232EIDWR | MAX3232ECDR |
|---|---|---|---|---|---|---|
| Package | 16-pin SOIC (DW) | 16-pin SOIC (DW) | 16-pin SOIC (IDR) | 16-pin SOIC (IDR) | 16-pin SOIC (DW) | 16-pin SOIC (CDR) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Transmitters | 2 | 2 | 2 | 2 | 2 | 2 |
| Receivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Charge-Pump Architecture | Capacitive voltage generator with external capacitors | Capacitive voltage generator | Capacitive voltage generator | Capacitive voltage generator | Capacitive voltage generator | Capacitive voltage generator |
| Interface Standard | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 |
מבדילים עיקריים
- Integrated ESD protection for externally accessible serial connectors (לעומתTRS232EIDWR)
- Complete dual-channel interface in a standard 16-pin SOIC (לעומתMAX232EIDR)
- Purpose-built 250kbps legacy RS-232 performance (לעומתMAX3232EIDR)
הערות תכנון
Place the four external charge-pump capacitors and the supply bypass capacitor as close as practical to their associated MAX232ECDWR pins. Keep the C1, C2, and C3 loop compact and provide a direct ground return to the IC. Long capacitor leads add inductance to the switching charge-pump loop and can increase ringing or supply noise, which may appear on transmitted signals.
Separate connector-side RS-232 nets from sensitive logic or analog traces. The transmitter outputs experience large bipolar swings, so avoid routing them beneath clocks, reference-voltage nets, or precision measurement inputs. Maintain a controlled ground reference between communicating systems and use the board's established chassis or signal-ground strategy to prevent an unintended ground potential difference from shifting receiver thresholds.
Do not substitute arbitrary charge-pump capacitor values when replacing the MAX232ECDWR with the TRS232EIDWR or another MAX232-family device. TI support guidance specifically notes that C1 through C4 and the bypass capacitor should be checked against the alternative device's recommendations. Also confirm the 4.5V to 5.5V supply requirement and the selected suffix's temperature and protection configuration before releasing a substitution.
מידע על תאימות
The device is identified as an RS-232 transceiver with IEC 61000-4-2 electrostatic-discharge protection. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the listed part information and are therefore recorded as unknown.