Texas Instruments

MAX232ECN - Dual RS-232 Transceiver, ESD Protected | TI

MPN: MAX232ECN ✓ פעיל
4.5 V to 5.5 V (single supply) Vdss 8 mA Id TIA/EIA-232-F compliant output levels Rds(on) 16-pin PDIP (DIP-16) Package
כמות הזמנה מינימלית: 1 |

MAX232ECN סקירה

The Texas Instruments MAX232ECN is a dual-channel RS-232 line driver/receiver transceiver operating from a single 4.5V to 5.5V supply, delivering 250kbps data rates in a 16-pin PDIP (DIP-16) package with enhanced IEC61000-4-2 ESD protection on the RS-232 lines.

An RS-232 transceiver is an interface IC that converts TTL/CMOS logic levels (0V to 5V) to the TIA/EIA-232-F voltage levels (approximately +/-5V to +/-15V) required for serial communication between equipment such as terminals, modems, and embedded microcontroller ports. Within the interface IC hierarchy, the MAX232 family is the industry-standard solution for short-haul asynchronous serial links, sitting between a UART and the physical RS-232 cable connector.

Key features include a capacitive charge-pump voltage generator that develops the +/-9V RS-232 output swings from a single 5V rail, eliminating the need for bipolar supplies. Each receiver converts RS-232 inputs down to 5V TTL/CMOS levels with a typical 1.3V threshold, 0.5V typical hysteresis for noise immunity, and the ability to withstand +/-30V input swings. The E-grade device adds enhanced ESD robustness per IEC61000-4-2 on the transceiver lines.

Architecturally, the part contains two drivers and two receivers (2/2 configuration) plus two charge pumps requiring only four small external capacitors. According to the TI MAX232 datasheet, low operating supply current of typically 8mA makes it practical for battery-backed and industrial serial ports, while the 250kbps maximum data rate covers the vast majority of legacy serial applications.

Typical applications include legacy RS-232 ports on industrial equipment, point-of-sale terminals, motor drives and PLC serial debugging consoles, and telecom/modem interfaces. It is the go-to part for adding a robust serial port to a 5V microcontroller such as the PIC24 or XMC families.

Design-wise, use four 0.1uF charge-pump capacitors (or follow the capacitor value table in the datasheet for higher data rates), keep the capacitors close to pins 1-6, and place a 1uF bulk capacitor on VCC. Never exceed the +/-30V receiver input rating.

This page adds value beyond the datasheet by synthesizing drop-in alternatives, per-application selection guidance, and practical design notes in one place.

חלופות תחליף ישיר עבור MAX232ECN — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם MAX232ECN (אותו גורם צורה וטביעת רגל) — שונים ב Package, Mounting Type, Maximum Data Rate, ESD Protection, Product Type.

Analog Devices
Package: 16-lead plastic DIP
Product Type: Dual RS-232 line-driver and line-receiver transceiver
השווה עם MAX232ECN →
Texas Instruments
Package: 16-pin PDIP
Mounting Type: Through Hole
Product Type: RS-232 transceiver
השווה עם MAX232ECN →
Texas Instruments
Package: 16-pin PDIP
Maximum Data Rate: 120 kbit/s
ESD Protection: ±2 kV
השווה עם MAX232ECN →

MAX232EIN

✅ Drop-In ⚠️ מפרטים לא מאומתים
Texas Instruments
📦 PDIP-16
RS-232 transceiver · 2 · 2 · 4.5 V to 5.5 V · 5 V · 250 kbps · 16-pin PDIP · Through Hole

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

MAX232ACN

✅ Drop-In ⚠️ מפרטים לא מאומתים
📦 PDIP-16
commercial grade without IEC61000-4-2 enhanced ESD protection (standard +/-8kV class protection only), otherwise pin-to-pin

📋 חלופה להתייחסות (לא בקטלוג)

MAX232N

✅ Drop-In ⚠️ מפרטים לא מאומתים
Texas Instruments
📦 PDIP-16
Dual RS-232 driver/receiver · 2 · 2 · 5 V · 120 kbit/s · ±9 V · ±30 V · 1.3 V

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

MAX202ECN

✅ Drop-In ⚠️ מפרטים לא מאומתים
📦 PDIP-16
reduced ESD rating vs E-grade MAX232E, 120kbps class speed, pin-to-pin same package

📋 חלופה להתייחסות (לא בקטלוג)

ADM232AAN

✅ Drop-In
Analog Devices
📦 PDIP-16
Dual RS-232 line-driver and line-receiver transceiver · 200 kB/s · 2 · 2 · 5 V · 0.1 µF · ±9 V with 5 V supply · ±30 V

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

ICL232

✅ Drop-In
📦 PDIP-16
Intersil/Renesas pin-compatible 2/2 RS-232 transceiver, single 5V supply, minor parametric differences vs MAX232E

📋 חלופה להתייחסות (לא בקטלוג)

MAX232ECN מפרטים

פונקציה RS-232 line driver/receiver
Configuration 2 drivers / 2 receivers (2/2 full duplex)
Supply Voltage Range 4.5 V to 5.5 V (single supply)
Typical Supply Current 8 mA
Maximum Data Rate 250 kbps
Output Voltage Swing +/-9 V typical at 5V supply (from charge pump)
Receiver Input Voltage Range +/-30 V
Receiver Threshold 1.3 V typical
Receiver Hysteresis 0.5 V typical
ESD Protection IEC61000-4-2 protected transceiver lines
Logic Levels 5V TTL/CMOS compatible
מארז 16-pin PDIP (DIP-16)
Number of External Capacitors 4 charge-pump capacitors
סוג הרכבה Through-hole
Standards TIA/EIA-232-F compliant output levels

תצורת פינים של MAX232ECN

DIP-16 Package Pinout Diagram DIP-16 16-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 DIP-16
פין 1 C1+ — Charge-pump flying capacitor 1 positive terminal
פין 2 V+ — Positive charge-pump output (typically +9V)
פין 3 C1- — Charge-pump flying capacitor 1 negative terminal
פין 4 C2+ — Charge-pump flying capacitor 2 positive terminal
פין 5 C2- — Charge-pump flying capacitor 2 negative terminal
פין 6 V- — Negative charge-pump output (typically -9V)
פין 7 T2OUT — RS-232 output of driver 2
פין 8 R2IN — RS-232 input of receiver 2 (tolerates +/-30V)
פין 9 R2OUT — TTL/CMOS output of receiver 2
פין 10 T2IN — TTL/CMOS input of driver 2
פין 11 T1IN — TTL/CMOS input of driver 1
פין 12 R1OUT — TTL/CMOS output of receiver 1
פין 13 R1IN — RS-232 input of receiver 1 (tolerates +/-30V)
פין 14 T1OUT — RS-232 output of driver 1
פין 15 GND — Ground
פין 16 VCC — Supply voltage, 4.5V to 5.5V

יישומים טיפוסיים

MAX232ECN מתאים עבור 6 יישוםs: Industrial PLC and Motor Drive Serial Consoles, Point-of-Sale and Retail Terminal Ports, Legacy Telecom and Modem Interfaces, Embedded Development and Debug Boards, Medical Instrument Service Ports, Battery-Backed Data Loggers.

🏭

Industrial PLC and Motor Drive Serial Consoles

The MAX232ECN fits industrial serial debugging and configuration consoles because its receivers tolerate +/-30V input swings and its 0.5V typical hysteresis rejects noise picked up on long plant-floor cables. The E-grade IEC61000-4-2 line protection absorbs static discharge when technicians connect laptops to service ports. Placed between the controller UART (5V TTL/CMOS) and the D-9 or D-25 connector, the 2/2 channel configuration covers a full TX/RX duplex link with the charge pump generating +/-9V levels from a single 5V rail, eliminating bipolar supplies in drive and PLC cabinets. At typical console rates of 9600 to 115200bps, the 250kbps capability provides ample margin.

🔧

Point-of-Sale and Retail Terminal Ports

Retail terminals such as receipt printers, barcode scanners, and cash-drawer interfaces still communicate over RS-232. The MAX232ECN suits this environment because frequent customer contact makes ESD events routine, and the E-grade's IEC61000-4-2 transceiver-line protection plus the +/-30V receiver tolerance handle misuse and cable hot-plugging. Operating from the terminal's single 5V supply, the internal charge pump replaces the +/-12V rails legacy designs required, cutting bill-of-material cost and board space. Its 250kbps rating comfortably exceeds printer serial rates, and the 16-pin through-hole PDIP simplifies field-serviceable, hand-solderable designs.

🌐

Legacy Telecom and Modem Interfaces

The MAX232ECN directly bridges 5V digital logic to TIA/EIA-232-F modems, DCE equipment, and telecom back-office gear. Its charge-pump generator produces the standard +/-9V output swing from a single 5V rail, while each receiver converts RS-232 levels back to 5V TTL/CMOS with the 1.3V typical threshold specified in the datasheet. The 250kbps data rate supports V.90-class modem serial speeds and higher, and receiver hysteresis of 0.5V typical suppresses reflections on long cable runs. Because the E-grade adds line-side ESD robustness, telco-room handling and repeated cable cycles are accommodated without external TVS arrays.

🧩

Embedded Development and Debug Boards

Every classic embedded development board includes an RS-232 console, and the MAX232ECN is the canonical choice. Connecting a microcontroller UART (TX, RX at 5V TTL/CMOS) through the transceiver to a DB-9 connector gives engineers a robust terminal link for bootloaders, logs, and command consoles. The single-supply charge pump means a 5V-only bench board needs no extra rails, and four 0.1uF capacitors plus one bulk capacitor complete the design. Through-hole DIP-16 mounting suits prototyping sockets, and the 250kbps limit exceeds typical 115200bps console rates with headroom for faster flashing protocols.

💊

Medical Instrument Service Ports

Diagnostic and monitoring equipment commonly retains an RS-232 service interface for calibration, firmware updates, and log retrieval. The MAX232ECN fits because the E-grade line protection addresses the electrostatic environment of patient-adjacent equipment handling, and the +/-30V receiver rating tolerates legacy device interconnection without damage. The single 5V supply and 8mA typical current keep power budgets modest in portable instruments. Its deterministic TTL/CMOS threshold of 1.3V typical and 0.5V typical hysteresis give reliable data recovery on shielded cable runs between the instrument and service laptop during calibration sessions.

⚡

Battery-Backed Data Loggers

Standalone data loggers with occasional RS-232 download ports benefit from the MAX232ECN's low typical supply current of 8mA and its ability to sit idle between downloads. The charge pump only needs four small capacitors, keeping the logger's battery-powered board simple, while the +/-30V receiver tolerance survives cables attached by field personnel. At standard logging transfer rates far below the 250kbps ceiling, the transceiver completes multi-hundred-kilobyte downloads in seconds, limiting the on-time penalty on the battery. The DIP-16 through-hole package suits the hand-repairable, long-lifecycle character of logging hardware.

What is the MAX232ECN?
The MAX232ECN is a Texas Instruments dual RS-232 line driver/receiver in a 16-pin PDIP package. It operates from a single 4.5V to 5.5V supply, uses an internal capacitive charge pump to generate the TIA/EIA-232-F output levels, transfers data at up to 250kbps, and includes IEC61000-4-2 enhanced ESD protection on the transceiver lines. Each receiver converts RS-232 inputs of up to +/-30V to 5V TTL/CMOS levels with a typical 1.3V threshold.
What supply voltage does the MAX232ECN require?
The MAX232ECN operates from a single supply of 4.5V to 5.5V, per the TI datasheet. No bipolar rails are needed because an internal charge-pump voltage generator, using four small external capacitors, develops the +/-9V RS-232 output swing from the 5V rail. Typical operating supply current is about 8mA, and a bulk capacitor on VCC plus local decoupling is recommended for charge-pump stability.
What is the maximum data rate of the MAX232ECN?
The MAX232ECN supports data rates up to 250kbps, according to the Texas Instruments datasheet. This covers virtually all legacy RS-232 applications such as PLC and motor-drive consoles, point-of-sale terminals, and industrial serial ports, which typically run at 9600 to 115200bps. Higher-speed RS-485 style links or multi-Mbps interfaces require a different transceiver family, not this part.
What is the difference between MAX232ECN and MAX232EIN?
Both are E-grade dual RS-232 driver/receivers from the same Texas Instruments/MAXIM family with identical die, function, and 16-pin DIP pinout. The difference is the package and temperature grade: MAX232ECN is the commercial plastic DIP-16 part, while MAX232EIN is the industrial-temperature-grade DIP-16 variant. They are pin-to-pin drop-in replacements for each other; choose the IN suffix when the board must operate across industrial ambient temperatures.
What is the best drop-in replacement for MAX232ECN?
The closest drop-in replacements are same-family TI parts in the same 16-pin DIP footprint: MAX232EIN (industrial grade, same die) and MAX232ACN (commercial grade with standard ESD protection). Cross-brand pin-compatible options include the ADM232A from Analog Devices and the ICL232 line from Intersil/Renesas, which replicate the 2/2 driver/receiver, single 5V supply, and DIP-16 pinout with minor parametric differences. Verify ESD ratings and temperature grade before substituting.
Can ADM232A replace MAX232ECN?
Yes. The Analog Devices ADM232A is a pin-compatible cross-brand equivalent: it is a high-speed 2-driver/2-receiver RS-232 transceiver in a 16-pin DIP that runs from a single 5V supply with an on-chip charge pump, matching the MAX232ECN footprint and function. Expect minor parametric differences in data rate (the ADM232A is faster) and ESD specification details. Review the ADI datasheet against your design before qualifying the substitution.
When should I choose MAX232ECN over MAX232N?
Choose the MAX232ECN when your RS-232 port connects to external cables exposed to static discharge or harsh industrial environments, because the E-grade adds IEC61000-4-2 enhanced ESD protection on the transceiver lines. Choose the standard MAX232N when the port is internal and already protected, typically at lower cost. Both share the identical 16-pin DIP pinout, 4.5V to 5.5V single supply, and 250kbps data rate, so they are drop-in interchangeable on the PCB.
Is MAX232ECN suitable for industrial RS-232 ports?
Yes. The MAX232ECN fits industrial serial port duty well: it tolerates +/-30V receiver inputs, offers 0.5V typical receiver hysteresis for noise rejection on long cables, and adds IEC61000-4-2 ESD protection on the lines. With a 4.5V to 5.5V supply and 8mA typical current, it integrates cleanly into 5V PLC, drive, and instrumentation boards. For boards operating over wide industrial temperature ranges, select the industrial-grade MAX232EIN variant instead.
What capacitors are needed around the MAX232ECN?
The MAX232ECN charge pump requires four external capacitors: two flying capacitors across C1+ / C1- (pins 1 and 3) and C2+ / C2- (pins 4 and 5), plus V+ and V- reservoir capacitors at pins 2 and 6, and a decoupling capacitor on VCC. Refer to the capacitor selection table in the Texas Instruments MAX232 datasheet for values at your operating data rate and supply. Keep all charge-pump capacitors close to pins 1-6 to minimize EMI from the switching pump.
What are the key specifications of MAX232ECN engineers should know?
The MAX232ECN is a 2-driver/2-receiver RS-232 transceiver on a single 4.5V to 5.5V supply, delivering +/-9V output swings from an internal charge pump and supporting 250kbps. Receivers tolerate +/-30V inputs with a 1.3V typical threshold and 0.5V typical hysteresis, and the transceiver lines carry IEC61000-4-2 enhanced ESD protection. Typical supply current is 8mA, and the part is housed in a 16-pin through-hole PDIP. These figures come from the TI MAX232 datasheet family documentation.
Where can I download the MAX232ECN datasheet PDF?
Download the datasheet directly from the Texas Instruments product page at ti.com/product/MAX232, which links the current MAX232 family datasheet covering the MAX232E (E-grade, IEC61000-4-2 protection) variants including the MAX232ECN. The datasheet contains the complete pin description table, charge-pump capacitor selection table, electrical characteristics, and typical application circuits. A Request a Quote form on this page remains available for pricing and stock inquiries.
What is the MAX232ECN pinout on the 16-pin DIP package?
Pins 1 through 6 host the charge pump: C1+ (1), V+ (2), C1- (3), C2+ (4), C2- (5), V- (6). Pins 7-14 are the transceiver lines: T2OUT (7), R2IN (8), R2OUT (9), T2IN (10), T1IN (11), R1OUT (12), R1IN (13), T1OUT (14). Pin 15 is GND and pin 16 is VCC. Always confirm against the pin description table in the TI MAX232 datasheet before routing the PCB.
What is the price of MAX232ECN?
Pricing for the MAX232ECN depends on quantity, packaging, and current market stock, and changes frequently. Use the Request a Quote form on this page to obtain a current, quantity-based quotation directly from XAIPART, including lead time and available packing options. There is no MOQ restriction beyond the manufacturer's packaging quantity, and quotes typically return within one business day for in-stock material.
Where to buy MAX232ECN online?
You can purchase the MAX232ECN through the Request a Quote form on this XAIPART product page. Submit the required quantity and target delivery date, and XAIPART will respond with pricing, stock status, and lead time. Order the part in its standard 16-pin PDIP through-hole package, and request cut-tape or tube quantities if your assembly process requires partial packaging rather than full factory tubes.
What is the lead time for MAX232ECN?
Lead time for the MAX232ECN varies with market availability and order quantity, so request the current figure via the Request a Quote form on this page. Texas Instruments lists the MAX232E family as active (not end-of-life), so ongoing production supply is supported; distributor stock is generally replenished regularly. For scheduled production builds, quote several months ahead so allocation and reel or tube quantities can be reserved.
Is the MAX232ECN still in production and RoHS compliant?
Texas Instruments lists the MAX232 family, which includes the MAX232ECN, as an active product line on its website, so the device remains in production. For definitive RoHS, REACH, and lead-free status of the exact CN suffix ordering code, consult the TI product page or the environmental compliance certificate for this specific part number, since compliance declarations are issued per ordering-code suffix. Request supporting compliance documents through the quote form if needed.

נתוני עזר הנדסיים עבור MAX232ECN — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the MAX232ECN when you need a 5V-only, through-hole dual RS-232 transceiver with enhanced ESD protection for an externally cabled port in commercial or light-industrial temperatures - it is the standard choice for PLC consoles, POS terminals, and development boards. Choose MAX232EIN if the board must operate across industrial temperature extremes: it is the same die in the same DIP-16 footprint. Choose MAX232ACN or MAX232N to save cost on internal, protected ports where IEC61000-4-2 line robustness is unnecessary. Cross-brand, the Analog Devices ADM232A is the strongest pin-compatible substitute with higher speed, and the Renesas/Intersil ICL232 suits second-source sourcing at 120kbps-class rates. All candidates share the single 5V supply, 2/2 channel configuration, and DIP-16 pinout, so PCB reuse is direct; the main trade-offs are ESD rating, data rate, and temperature grade.

השוואה עם חלופות

פרמטר מוצר זה MAX232EIN MAX232ACN ADM232A ICL232
Package PDIP-16 PDIP-16 - same PDIP-16 - same PDIP-16 - same PDIP-16 - same
Brand Texas Instruments Texas Instruments Texas Instruments Analog Devices Renesas Electronics (Intersil)
Supply Voltage 4.5V to 5.5V single supply 4.5V to 5.5V 4.5V to 5.5V 4.5V to 5.5V 4.5V to 5.5V
ESD Protection IEC61000-4-2 enhanced (E-grade) IEC61000-4-2 enhanced (E-grade) - same Standard (non-E grade) Enhanced ESD rating per ADI datasheet Standard RS-232 protection
Data Rate 250 kbps 250 kbps 250 kbps Higher (high-speed, per ADI datasheet) 120 kbps class
Driver/Receiver Count 2 / 2 2 / 2 2 / 2 2 / 2 2 / 2
Temperature Grade Commercial (CN suffix) Industrial (IN suffix) Commercial Industrial options available Commercial/Industrial options

מבדילים עיקריים

  • IEC61000-4-2 enhanced ESD protection on transceiver lines (לעומתMAX232ACN)
  • 250kbps data rate headroom (לעומתICL232)
  • Commercial grade cost efficiency for indoor ports (לעומתMAX232EIN)

הערות תכנון

Place the four charge-pump capacitors (C1+ / C1- and C2+ / C2- plus the V+ and V- reservoirs) as close as possible to pins 1 through 6. The charge pump switches continuously and long traces radiate EMI and degrade output swing. Use the capacitor selection table in the TI MAX232 datasheet to pick values for your data rate; 0.1uF is typical at moderate rates. Add a bulk capacitor at VCC pin 16 near pin 15 (GND) and keep the RS-232 traces on pins 7, 8, 13, 14 short and away from clock lines.

Never apply receiver inputs beyond +/-30V, and do not drive TOUT pins below V- or above V+. A frequent failure mode is wiring a MAX232 output directly to another MAX232 output (driver-to-driver), which violates output drive assumptions. Also remember that RS-232 is idle-low/mark = negative voltage, so scope probes set to 0V-referenced logic interpretation will show inverted-looking waveforms. If your UART is 3.3V-only, this 5V part is not the right choice - select a 3.3V transceiver family instead.

The internal charge pump operates continuously and can inject ripple into nearby analog circuitry. Estimated: a typical pump switching in the tens-of-kHz range with 0.1uF reservoirs produces small but measurable ripple on V+ / V-; routing the pump nodes away from ADC reference and audio lines, or increasing reservoir capacitance, reduces the ripple amplitude. Ground the part through a short trace to a solid ground node and avoid sharing the pump ground return with sensitive analog returns. This guidance follows the layout recommendations of the manufacturer datasheet family application section.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

Compliance status for the exact MAX232ECN ordering code was not stated in the source material; consult the TI product page or request environmental certificates via the quote form.

הנתונים אומתו בתאריך: 2026-11-08 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

MAX232ECN datasheet MAX232ECN datasheet pdf MAX232ECN pinout MAX232ECN equivalent MAX232ECN replacement MAX232ECN vs MAX232EIN Texas Instruments MAX232ECN MAX232ECN price MAX232ECN stock MAX232E DIP-16 RS-232 transceiver MAX232E application circuit MAX232ECN cross reference

רכיבים ומונחים קשורים

Texas Instruments MAX232ECN MAX232EIN MAX232ACN ADM232A ICL232 RS-232 TIA/EIA-232-F IEC61000-4-2 RS-232 transceiver line driver/receiver interface IC charge pump PDIP-16 dual in-line package surface-mount/through-hole UART ESD protection 250 kbps RoHS PLC serial console point-of-sale terminal receiver hysteresis
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר