MAX232ECN - Dual RS-232 Transceiver, ESD Protected | TI
MPN: MAX232ECN ✓ Hoạt độngMAX232ECN Tóm tắt
An RS-232 transceiver is an interface IC that converts TTL/CMOS logic levels (0V to 5V) to the TIA/EIA-232-F voltage levels (approximately +/-5V to +/-15V) required for serial communication between equipment such as terminals, modems, and embedded microcontroller ports. Within the interface IC hierarchy, the MAX232 family is the industry-standard solution for short-haul asynchronous serial links, sitting between a UART and the physical RS-232 cable connector.
Key features include a capacitive charge-pump voltage generator that develops the +/-9V RS-232 output swings from a single 5V rail, eliminating the need for bipolar supplies. Each receiver converts RS-232 inputs down to 5V TTL/CMOS levels with a typical 1.3V threshold, 0.5V typical hysteresis for noise immunity, and the ability to withstand +/-30V input swings. The E-grade device adds enhanced ESD robustness per IEC61000-4-2 on the transceiver lines.
Architecturally, the part contains two drivers and two receivers (2/2 configuration) plus two charge pumps requiring only four small external capacitors. According to the TI MAX232 datasheet, low operating supply current of typically 8mA makes it practical for battery-backed and industrial serial ports, while the 250kbps maximum data rate covers the vast majority of legacy serial applications.
Typical applications include legacy RS-232 ports on industrial equipment, point-of-sale terminals, motor drives and PLC serial debugging consoles, and telecom/modem interfaces. It is the go-to part for adding a robust serial port to a 5V microcontroller such as the PIC24 or XMC families.
Design-wise, use four 0.1uF charge-pump capacitors (or follow the capacitor value table in the datasheet for higher data rates), keep the capacitors close to pins 1-6, and place a 1uF bulk capacitor on VCC. Never exceed the +/-30V receiver input rating.
This page adds value beyond the datasheet by synthesizing drop-in alternatives, per-application selection guidance, and practical design notes in one place.
Bộ thay thế dễ dàng lắp đặt cho MAX232ECN — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX232ECN (cùng hình factor và footprint) — khác nhau ở Package, Mounting Type, Maximum Data Rate, ESD Protection, Product Type.
MAX232EIN
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX232ACN
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MAX232N
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MAX202ECN
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADM232AAN
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ICL232
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX232ECN Thông số kỹ thuật
| Chức năng | RS-232 line driver/receiver |
| Configuration | 2 drivers / 2 receivers (2/2 full duplex) |
| Supply Voltage Range | 4.5 V to 5.5 V (single supply) |
| Typical Supply Current | 8 mA |
| Maximum Data Rate | 250 kbps |
| Output Voltage Swing | +/-9 V typical at 5V supply (from charge pump) |
| Receiver Input Voltage Range | +/-30 V |
| Receiver Threshold | 1.3 V typical |
| Receiver Hysteresis | 0.5 V typical |
| ESD Protection | IEC61000-4-2 protected transceiver lines |
| Logic Levels | 5V TTL/CMOS compatible |
| Hộp | 16-pin PDIP (DIP-16) |
| Number of External Capacitors | 4 charge-pump capacitors |
| Kiểu lắp đặt | Through-hole |
| Standards | TIA/EIA-232-F compliant output levels |
Cấu hình chân MAX232ECN
| Chân 1 | C1+ — Charge-pump flying capacitor 1 positive terminal |
| Chân 2 | V+ — Positive charge-pump output (typically +9V) |
| Chân 3 | C1- — Charge-pump flying capacitor 1 negative terminal |
| Chân 4 | C2+ — Charge-pump flying capacitor 2 positive terminal |
| Chân 5 | C2- — Charge-pump flying capacitor 2 negative terminal |
| Chân 6 | V- — Negative charge-pump output (typically -9V) |
| Chân 7 | T2OUT — RS-232 output of driver 2 |
| Chân 8 | R2IN — RS-232 input of receiver 2 (tolerates +/-30V) |
| Chân 9 | R2OUT — TTL/CMOS output of receiver 2 |
| Chân 10 | T2IN — TTL/CMOS input of driver 2 |
| Chân 11 | T1IN — TTL/CMOS input of driver 1 |
| Chân 12 | R1OUT — TTL/CMOS output of receiver 1 |
| Chân 13 | R1IN — RS-232 input of receiver 1 (tolerates +/-30V) |
| Chân 14 | T1OUT — RS-232 output of driver 1 |
| Chân 15 | GND — Ground |
| Chân 16 | VCC — Supply voltage, 4.5V to 5.5V |
Ứng dụng tiêu biểu
MAX232ECN phù hợp cho 6 Áp dụngs: Industrial PLC and Motor Drive Serial Consoles, Point-of-Sale and Retail Terminal Ports, Legacy Telecom and Modem Interfaces, Embedded Development and Debug Boards, Medical Instrument Service Ports, Battery-Backed Data Loggers.
Industrial PLC and Motor Drive Serial Consoles
The MAX232ECN fits industrial serial debugging and configuration consoles because its receivers tolerate +/-30V input swings and its 0.5V typical hysteresis rejects noise picked up on long plant-floor cables. The E-grade IEC61000-4-2 line protection absorbs static discharge when technicians connect laptops to service ports. Placed between the controller UART (5V TTL/CMOS) and the D-9 or D-25 connector, the 2/2 channel configuration covers a full TX/RX duplex link with the charge pump generating +/-9V levels from a single 5V rail, eliminating bipolar supplies in drive and PLC cabinets. At typical console rates of 9600 to 115200bps, the 250kbps capability provides ample margin.
Được đề xuất
Point-of-Sale and Retail Terminal Ports
Retail terminals such as receipt printers, barcode scanners, and cash-drawer interfaces still communicate over RS-232. The MAX232ECN suits this environment because frequent customer contact makes ESD events routine, and the E-grade's IEC61000-4-2 transceiver-line protection plus the +/-30V receiver tolerance handle misuse and cable hot-plugging. Operating from the terminal's single 5V supply, the internal charge pump replaces the +/-12V rails legacy designs required, cutting bill-of-material cost and board space. Its 250kbps rating comfortably exceeds printer serial rates, and the 16-pin through-hole PDIP simplifies field-serviceable, hand-solderable designs.
Được đề xuất
Legacy Telecom and Modem Interfaces
The MAX232ECN directly bridges 5V digital logic to TIA/EIA-232-F modems, DCE equipment, and telecom back-office gear. Its charge-pump generator produces the standard +/-9V output swing from a single 5V rail, while each receiver converts RS-232 levels back to 5V TTL/CMOS with the 1.3V typical threshold specified in the datasheet. The 250kbps data rate supports V.90-class modem serial speeds and higher, and receiver hysteresis of 0.5V typical suppresses reflections on long cable runs. Because the E-grade adds line-side ESD robustness, telco-room handling and repeated cable cycles are accommodated without external TVS arrays.
Được đề xuất
Embedded Development and Debug Boards
Every classic embedded development board includes an RS-232 console, and the MAX232ECN is the canonical choice. Connecting a microcontroller UART (TX, RX at 5V TTL/CMOS) through the transceiver to a DB-9 connector gives engineers a robust terminal link for bootloaders, logs, and command consoles. The single-supply charge pump means a 5V-only bench board needs no extra rails, and four 0.1uF capacitors plus one bulk capacitor complete the design. Through-hole DIP-16 mounting suits prototyping sockets, and the 250kbps limit exceeds typical 115200bps console rates with headroom for faster flashing protocols.
Được đề xuất
Medical Instrument Service Ports
Diagnostic and monitoring equipment commonly retains an RS-232 service interface for calibration, firmware updates, and log retrieval. The MAX232ECN fits because the E-grade line protection addresses the electrostatic environment of patient-adjacent equipment handling, and the +/-30V receiver rating tolerates legacy device interconnection without damage. The single 5V supply and 8mA typical current keep power budgets modest in portable instruments. Its deterministic TTL/CMOS threshold of 1.3V typical and 0.5V typical hysteresis give reliable data recovery on shielded cable runs between the instrument and service laptop during calibration sessions.
Được đề xuất
Battery-Backed Data Loggers
Standalone data loggers with occasional RS-232 download ports benefit from the MAX232ECN's low typical supply current of 8mA and its ability to sit idle between downloads. The charge pump only needs four small capacitors, keeping the logger's battery-powered board simple, while the +/-30V receiver tolerance survives cables attached by field personnel. At standard logging transfer rates far below the 250kbps ceiling, the transceiver completes multi-hundred-kilobyte downloads in seconds, limiting the on-time penalty on the battery. The DIP-16 through-hole package suits the hand-repairable, long-lifecycle character of logging hardware.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX232ECN — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX232EIN | MAX232ACN | ADM232A | ICL232 |
|---|---|---|---|---|---|
| Package | PDIP-16 | PDIP-16 - same | PDIP-16 - same | PDIP-16 - same | PDIP-16 - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices | Renesas Electronics (Intersil) |
| Supply Voltage | 4.5V to 5.5V single supply | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V |
| ESD Protection | IEC61000-4-2 enhanced (E-grade) | IEC61000-4-2 enhanced (E-grade) - same | Standard (non-E grade) | Enhanced ESD rating per ADI datasheet | Standard RS-232 protection |
| Data Rate | 250 kbps | 250 kbps | 250 kbps | Higher (high-speed, per ADI datasheet) | 120 kbps class |
| Driver/Receiver Count | 2 / 2 | 2 / 2 | 2 / 2 | 2 / 2 | 2 / 2 |
| Temperature Grade | Commercial (CN suffix) | Industrial (IN suffix) | Commercial | Industrial options available | Commercial/Industrial options |
Bảo phân biệt quan trọng
- IEC61000-4-2 enhanced ESD protection on transceiver lines (vsMAX232ACN)
- 250kbps data rate headroom (vsICL232)
- Commercial grade cost efficiency for indoor ports (vsMAX232EIN)
Ghi chú thiết kế
Place the four charge-pump capacitors (C1+ / C1- and C2+ / C2- plus the V+ and V- reservoirs) as close as possible to pins 1 through 6. The charge pump switches continuously and long traces radiate EMI and degrade output swing. Use the capacitor selection table in the TI MAX232 datasheet to pick values for your data rate; 0.1uF is typical at moderate rates. Add a bulk capacitor at VCC pin 16 near pin 15 (GND) and keep the RS-232 traces on pins 7, 8, 13, 14 short and away from clock lines.
Never apply receiver inputs beyond +/-30V, and do not drive TOUT pins below V- or above V+. A frequent failure mode is wiring a MAX232 output directly to another MAX232 output (driver-to-driver), which violates output drive assumptions. Also remember that RS-232 is idle-low/mark = negative voltage, so scope probes set to 0V-referenced logic interpretation will show inverted-looking waveforms. If your UART is 3.3V-only, this 5V part is not the right choice - select a 3.3V transceiver family instead.
The internal charge pump operates continuously and can inject ripple into nearby analog circuitry. Estimated: a typical pump switching in the tens-of-kHz range with 0.1uF reservoirs produces small but measurable ripple on V+ / V-; routing the pump nodes away from ADC reference and audio lines, or increasing reservoir capacitance, reduces the ripple amplitude. Ground the part through a short trace to a solid ground node and avoid sharing the pump ground return with sensitive analog returns. This guidance follows the layout recommendations of the manufacturer datasheet family application section.
Thông tin tuân thủ
Compliance status for the exact MAX232ECN ordering code was not stated in the source material; consult the TI product page or request environmental certificates via the quote form.