MAX3232CPWRG4 - 250 kbps Dual RS-232 Transceiver, 3-5.5 V, 16-TSSOP | Texas Instruments
MPN: MAX3232CPWRG4 ✓ פעילMAX3232CPWRG4 סקירה
An RS-232 transceiver is the interface bridge between a modern CMOS/TTL microcontroller or host UART and the legacy plus or minus 5 V to plus or minus 15 V signalling world of the RS-232 standard. In the knowledge hierarchy it sits as RS-232 transceiver, then line driver and line receiver, then interface IC, then integrated circuit. The MAX3232 is a classic multi-channel RS-232 interface IC used wherever a system must talk to a serial port, console, or legacy peripheral over a cable.
Key features of the MAX3232 device include the on-chip dual charge-pump circuit that generates the positive and negative RS-232 voltage levels from a single 3 V to 5.5 V supply, plus or minus 15 kV ESD protection on the serial-port connection terminals including ground, and compliance with the requirements of TIA/EIA-232-F. Because both the charge pump and the level translation are integrated, no external negative rail or level shifter is required in the design.
Architecturally the device separates transmit and receive pins cleanly, with two dedicated driver outputs and two dedicated receiver inputs plus the enable pins for each channel, so each direction can be shut down independently to reduce supply current when the port is idle. The charge-pump section requires four external flying capacitors connected to the C1+, C1-, C2+ and C2- pins, which the manufacturer shows in the typical application circuit of the MAX3232 datasheet.
Typical applications include RS-232 console and debug ports on industrial equipment, point-of-sale terminals, serial bridges and protocol converters, test and measurement instrument front panels, and legacy DB9 or RJ45 serial connections to host computers and microcontrollers. The 16-pin TSSOP footprint keeps the design compact and is the standard footprint for this family in surface-mount production.
When laying out a board, keep the four charge-pump capacitors physically close to their respective pins and route the RS-232 connector side of the circuit away from sensitive analog or high-speed digital traces, since the driver outputs are high-voltage, high-slew-rate signals relative to the logic side of the board.
This page consolidates manufacturer specifications, a drop-in alternative matrix, comparison parameters and practical layout guidance for engineers who need to source, qualify or replace the MAX3232CPWRG4 without re-laying-out their RS-232 interface board.
חלופות תחליף ישיר עבור MAX3232CPWRG4 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MAX3232CPWRG4 (אותו גורם צורה וטביעת רגל) — שונים ב Transceiver Configuration, Maximum Data Rate, Package, ESD Protection, Interface Standard.
MAX3232EIPWRQ1
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←TRS3232ECPWR
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX3232ECPWR
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MAX3232IPWR
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←SP3232EBCY-L/TR
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MAX3232CPWRG4 מפרטים
| Product Type | RS-232 line driver/receiver (transceiver) IC |
| Number of Line Drivers | 2 |
| Number of Line Receivers | 2 |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection (Terminal to Terminal) | +/-15 kV |
| Standard Compliance | TIA/EIA-232-F |
| Charge Pump | Dual on-chip charge-pump circuit |
| External Charge-Pump Capacitors | 4 (C1+, C1-, C2+, C2-) |
| מארז | 16-pin TSSOP (PW) |
| סוג הרכבה | Surface Mount |
| Logic Levels (Driver Input / Receiver Output) | CMOS/TTL compatible |
| Transceiver Configuration | 2/2 (two drivers, two receivers) |
| סטטוס RoHS | Compliant (G4 suffix denotes lead-free green package) |
תצורת פינים של MAX3232CPWRG4
| פין 1 | C1+ — Charge-pump flying capacitor positive terminal |
| פין 2 | V+ — Charge-pump output supply (positive RS-232 rail node) |
| פין 3 | C1- — Charge-pump flying capacitor negative terminal |
| פין 4 | C2+ — Charge-pump flying capacitor positive terminal |
| פין 5 | C2- — Charge-pump flying capacitor negative terminal |
| פין 6 | V- — Charge-pump output supply (negative RS-232 rail node) |
| פין 7 | R1OUT — Receiver 1 output (logic level) |
| פין 8 | R1IN — Receiver 1 input (RS-232 level) |
| פין 9 | R2OUT — Receiver 2 output (logic level) |
| פין 10 | R2IN — Receiver 2 input (RS-232 level) |
| פין 11 | IN2 — Driver 2 input (logic level) |
| פין 12 | T2IN — Driver 2 data input (logic level) |
| פין 13 | T1IN — Driver 1 data input (logic level) |
| פין 14 | T2OUT — Driver 2 output (RS-232 level) |
| פין 15 | T1OUT — Driver 1 output (RS-232 level) |
| פין 16 | GND — Ground |
יישומים טיפוסיים
MAX3232CPWRG4 מתאים עבור 6 יישוםs: Industrial Console and Debug Serial Port, Point-of-Sale Terminal and Peripheral Interface, Serial Bridge and Protocol Converter, Test and Measurement Instrument Front Panel, Data Acquisition and Sensor Gateway Node, Legacy Computer and Peripheral Retrofit.
Industrial Console and Debug Serial Port
The MAX3232CPWRG4 fits console ports on industrial controllers, PLCs and test equipment because it delivers two RS-232 channels with a 250 kbps data rate from a single 3 V to 5.5 V rail, matching the supply of most modern embedded processors. A host UART on 3.3 V or 5 V connects directly to the CMOS-compatible driver inputs, while the receiver outputs translate the plus or minus RS-232 levels back to logic levels. The plus or minus 15 kV terminal-to-terminal ESD protection on the connector-side pins is the key benefit for cabinet-mounted equipment where the console cable is frequently plugged and unplugged by service technicians, adding a ruggedness layer that a bare UART pin cannot provide.
מומלץ
Point-of-Sale Terminal and Peripheral Interface
Point-of-sale terminals and receipt printers still rely on RS-232 for cash drawer, scale and printer signalling, and the MAX3232CPWRG4 provides the bipolar voltage levels those devices expect from a single supply. Two drivers and two receivers per package allow a single chip to handle both the outbound command channel and the inbound acknowledgement channel to the printer, which halves the interface count compared with single-channel parts. The 250 kbps ceiling is comfortably above the few kbit/s rates used by legacy POS peripherals, while the integrated charge pump removes the need for a separate negative rail in space-constrained terminal housings.
מומלץ
Serial Bridge and Protocol Converter
Protocol converters that bridge RS-232 to RS-485 or to a USB host benefit from the MAX3232CPWRG4 because its two channels can terminate a full-duplex RS-232 link with one package, leaving board area for the conversion side. The 250 kbps maximum data rate suits supervisory links, configuration ports and firmware update channels rather than high-speed data streaming. The 16-pin TSSOP package keeps the converter board compact, and the plus or minus 15 kV ESD rating protects the exposed connector pins that are typically routed to the enclosure edge in field-installed equipment.
מומלץ
Test and Measurement Instrument Front Panel
Laboratory and field-test instruments expose RS-232 ports for SCPI-style command and control, and the MAX3232CPWRG4 suits this role because the TIA/EIA-232-F compliant drivers and receivers deliver reliable signalling over multi-metre shielded cables. Its 3 V to 5.5 V operating range allows it to run from the same rail as the instrument's digital control section, minimising power tree complexity. For bench equipment that is repeatedly connected to customer laptops, the terminal-to-terminal ESD protection on the driver and receiver pins reduces the risk of instrument damage from electrostatic events during routine reconfiguration of the test setup.
מומלץ
Data Acquisition and Sensor Gateway Node
Remote data acquisition nodes and sensor gateways that must report to a host computer over RS-232 use the MAX3232CPWRG4 as the physical layer interface to the on-board microcontroller UART. The low single-supply requirement is valuable in gateway designs powered from small isolated DC-DC modules, since no additional negative rail is needed. With 250 kbps of headroom the link is more than adequate for periodic telemetry frames, and the integrated charge pump plus on-board level translation shortens the design cycle by removing discrete transistor inverter stages that older RS-232 designs required.
מומלץ
Legacy Computer and Peripheral Retrofit
Retrofit and adapter designs that let modern USB or embedded boards talk to legacy DB9 RS-232 peripherals are a classic use for the MAX3232CPWRG4 because the interface is a single IC plus four charge-pump capacitors and an optional protection network. The 16-pin TSSOP package is easy to place on a small adapter PCB, and the plus or minus 15 kV ESD rating is valuable on adapter boards that plug directly into an unshielded legacy port. Designers can reuse existing cable and connector wiring because the driver and receiver pin functions match the original RS-232 channel arrangement of the family.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MAX3232CPWRG4 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MAX3232EIPWR | TRS3232ECPWR | MAX3232ECPWR | SP3232EBCY-L/TR |
|---|---|---|---|---|---|
| Package | 16-TSSOP (PW) | 16-TSSOP (PW) - same | 16-TSSOP (PW) - same | 16-TSSOP (PW) - same | 16-pin narrow-body - verify lead pitch against 0.65 mm TSSOP land pattern |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | MaxLinear |
| Number of Drivers / Receivers | 2 / 2 | 2 / 2 | 2 / 2 | 2 / 2 | 2 / 2 |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Manufacturer Recommendation | Original MAX3232 grade, active orderable code | Recommended by the manufacturer for new designs | Newer enhanced family member | Improved direct drop-in replacement for MAX3232 | Second-source functional equivalent |
מבדילים עיקריים
- Original MAX3232 orderable code with the full 16-pin TSSOP footprint and 2/2 channel configuration (לעומתMAX3232EIPWR)
- Lower supply current and improved driver and receiver behaviour in the MAX3232E generation (לעומתMAX3232ECPWR)
- Second-source availability without redesign (לעומתSP3232EBCY-L/TR)
- Auto-shutdown and enhanced ESD options available in the same footprint (לעומתTRS3232ECPWR)
הערות תכנון
Place the four charge-pump capacitors directly across the C1+, C1-, C2+ and C2- pins with the shortest possible loop area. These switching nodes move at high frequency, so long traces act as antennas and couple switching noise into adjacent logic nets. Keep the V+ and V- connections to the capacitors short as well, and place the input and output bulk decoupling close to the supply pins to keep the charge-pump return current inside the device ground loop.
Do not route RS-232 driver outputs (T1OUT, T2OUT) alongside receiver inputs or logic-side signals on the same layer. The driver outputs swing to plus or minus RS-232 voltage levels with fast edge rates, and coupling from these nets into the receiver inputs or the host UART can produce corrupted characters and intermittent framing errors. Use a keep-out band and, where practical, route the connector side of the board on a separate layer or behind a ground guard.
For cable-attached ports, add a series protection network at the connector: a low-capacitance TVS diode array per line for surge and residual ESD events, plus a common-mode choke or small ferrite if the cable run is long. The integrated plus or minus 15 kV ESD protection is a last line of defence for the device itself and should be combined with external protection so that the connector pins, not the IC pins, absorb the bulk of the discharge energy.
The charge-pump section draws pulsed current from the supply while generating the bipolar rails, so the input supply must be able to source the charge-pump current spikes without excessive droop. Place a local ceramic capacitor plus a bulk electrolytic near the device and keep the ground return path short to the supply ground plane. If the interface shares a rail with switching converters, isolate the supply with a small ferrite bead or dedicated LDO to keep ripple off the receiver thresholds.
מידע על תאימות
The G4 suffix denotes the lead-free, RoHS-compliant green package variant from Texas Instruments. The device is a commercial and industrial interface IC and is not AEC-Q100 qualified. REACH, halogen-free and conflict-minerals declarations were not stated on the product pages and should be confirmed with the manufacturer before export-controlled or regulated use.