MAX335ENG+ - 8-Channel SPST Analog Switch | Analog Devices
MPN: MAX335ENG+ ✓ פעילMAX335ENG+ סקירה
An analog switch is an integrated semiconductor device that routes electrical signals between terminals under digital control. The MAX335 belongs to the broader analog switch IC category, which falls within interface ICs and semiconductor signal-routing devices. Unlike a mechanical relay, it provides compact, solid-state signal isolation and control. Its serial interface allows a host controller to manage eight switch channels with a compact command structure instead of requiring a dedicated control line for every channel.
The principal features of the MAX335ENG+ are eight separately controlled SPST channels, equal signal conduction in either direction, and an on-resistance stated as 100 Ω typical over the analog signal range. The MAX335ENG+ ordering code denotes the 24-pin PDIP configuration and the temperature range identified by the manufacturer’s part-numbering system. These characteristics make it useful where multiple analog or digital signals must be selected, isolated, or routed under software control.
The MAX335 uses a serial digital interface for switch control. Because all eight switches share the same serial control mechanism, the device can reduce control-line count compared with a bank of discrete mechanically controlled analog switches. The on-resistance remains approximately constant across the analog signal range, helping simplify impedance calculations when the switch is placed in series with a source or load. Signal integrity still depends on capacitance, bandwidth, layout, source impedance, and the frequency content carried by the selected channel.
Typical uses include test and measurement signal routing, communication equipment, industrial control interfaces, data-acquisition systems, and embedded control systems that need to connect one signal source to one of several destinations. The eight-channel SPST organization can also implement isolation between a shared analog bus and peripheral circuits. It is especially useful where compact control, bidirectional conduction, and individually addressable channels are more important than ultra-low resistance.
When laying out a MAX335ENG+ circuit, keep analog traces short and provide a clean ground reference because the serial interface and switched signals must not share noisy return paths. Confirm the control protocol and timing from the manufacturer datasheet before writing firmware. Treat the stated 100 Ω typical on-resistance as a real impedance in the signal path and include its attenuation when calculating sensor, amplifier, or ADC input networks.
חלופות תחליף ישיר עבור MAX335ENG+ — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
MAX335CNG+
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MAX335ENG
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX335ENG-T
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX335EWG-T
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX335ENG+ דירוגים מרביים ומאפיינים חשמליים
| Product Type | Serial-controlled analog switch IC |
| Number of Switches | 8 circuits |
| Switch Configuration | 1:1 SPST |
| On-Resistance | 100 Ω typical |
| Distributor-Reported On-Resistance | 150 Ω |
| Signal Conduction Direction | Equal in either direction |
| Control Interface | Serial digital interface |
| Channel Control | 8 separately controlled switches |
| מארז | 24-pin PDIP |
| סוג הרכבה | Through-hole |
| Off-State Leakage Current | 1 nA maximum |
| ECCN | EAR99 |
| Introduction Date | July 1, 1996 |
| Estimated End-of-Life Date | 2028 |
| Halogen-Free Status | Compliant |
מדריך תצורת פינים של MAX335ENG+ 24-pin pdip
תצורת פינים עבור MAX335ENG+ (מארזת 24-pin pdip). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור MAX335ENG+.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
MAX335ENG+ מתאים עבור 6 יישוםs: Data-Acquisition Signal Routing, Test and Measurement Fixture Control, Industrial Control Signal Isolation, Communication Equipment Path Selection, Embedded Interface Switching, Programmable Analog Backplane.
Data-Acquisition Signal Routing
The MAX335ENG+ fits data-acquisition systems that must route sensors, instrument outputs, or excitation signals under processor control. Its eight independently controlled SPST channels provide separate selection paths while the shared serial interface limits control-line demand. With 100 Ω typical on-resistance, the device is most appropriate when source impedance is high enough that the switch resistance does not dominate measurement accuracy. Keep switched traces short, establish a low-impedance analog ground, and account for the 100 Ω insertion resistance when scaling ADC input networks.
Test and Measurement Fixture Control
The MAX335ENG+ is suitable for test fixtures that connect instruments, standards, and device-under-test resources through software-addressable paths. Eight separately controlled SPST switches can isolate channels or connect a common resource to one destination at a time, while bidirectional conduction allows either the source or load side to be switched. The 100 Ω typical on-resistance can affect high-impedance measurements, so calibrate the fixture or use it where impedance variation is acceptable rather than in a precision low-resistance voltage path.
Industrial Control Signal Isolation
The MAX335ENG+ can isolate shared control or analog lines in industrial equipment when individual channels must be enabled according to machine state. Its eight separately controlled SPST switches permit firmware to establish signal paths without operating multiple relay coils. The serial control interface reduces the number of host pins needed for routing decisions, while the 24-pin PDIP package supports conventional through-hole assembly. Validate the exact operating-temperature grade, supply range, and signal ratings against the machine’s environmental requirements.
Communication Equipment Path Selection
The MAX335ENG+ can route communication signals among multiple circuit paths when the design needs eight individually controlled, bidirectional SPST channels. Bidirectional conduction is useful for shared buses, though the 100 Ω typical on-resistance introduces series loss and should be included in link-budget calculations for higher-frequency signals. Place the device away from switching-power nodes, provide a continuous ground path, and verify bandwidth and crosstalk characteristics for the actual channel impedance and clock rate.
Embedded Interface Switching
The MAX335ENG+ fits embedded systems that need software-controlled selection between external peripherals and shared buses. Its serial interface allows a microcontroller or programmable logic device to manage eight channels with a compact command sequence, reducing the GPIO burden associated with eight discrete control lines. Because every closed channel contributes approximately 100 Ω typical series resistance, design external buffers or instrumentation amplifiers when driving low-impedance inputs or measuring precision voltage thresholds.
Programmable Analog Backplane
The MAX335ENG+ can create a small programmable analog backplane in which one resource is connected to selected destinations through independent SPST channels. This arrangement is useful for power sequencing, source isolation, and repetitive test routing without relying on numerous mechanical relays. The shared serial control interface simplifies configuration, while the bidirectional switch behavior supports varied source and load arrangements. Use the datasheet timing information to avoid simultaneous switching events that could disturb sensitive downstream nodes.
נתוני עזר הנדסיים עבור MAX335ENG+ — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MAX335CNG+ | MAX335ENG | MAX335ENG-T | MAX335EWG-T |
|---|---|---|---|---|---|
| Package | 24-pin PDIP | 24-pin PDIP | 24-pin PDIP | 24-pin PDIP | 24-pin PDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Number of Switches | 8 | 8 | 8 | 8 | 8 |
| Switch Configuration | 1:1 SPST | 1:1 SPST | 1:1 SPST | 1:1 SPST | 1:1 SPST |
| Control Interface | Serial digital interface | Serial digital interface | Serial digital interface | Serial digital interface | Serial digital interface |
מבדילים עיקריים
- Eight independently controlled channels with a shared serial interface (לעומתMAX335CNG+)
- Bidirectional signal conduction (לעומתMAX335EWG-T)
- Documented 100 Ω typical on-resistance (לעומתMAX335ENG)
- Direct PCB reuse with established PDIP footprint (לעומתMAX335CNG+)
הערות תכנון
Treat each closed channel as a series 100 Ω element, as stated in the manufacturer datasheet, and include it in the source, load, and ADC input calculation. For a 10 kΩ source impedance, the switch resistance changes the divider by approximately 1%, while a 100 Ω source makes the added resistance much more significant. Use short traces, a stable ground reference, and the complete frequency-response data when routing higher-bandwidth signals.
Place the MAX335ENG+ close to the signals being routed and keep the serial interface traces away from sensitive analog nodes. Provide a direct ground return beneath or adjacent to the device, avoid long shared paths between analog channels and digital control, and provide test points for clock, data, and control signals. Although the MAX335ENG+ uses a through-hole PDIP package, careful analog trace routing remains important because every closed switch contributes resistance and board parasitics.
Do not assume that all MAX335 ordering suffixes have identical temperature, packing, or lifecycle meanings. Confirm the MAX335ENG+ suffix against the manufacturer ordering guide before substituting MAX335ENG, MAX335ENG-T, MAX335CNG+, or MAX335EWG-T. Also verify the serial-interface timing and logic levels in firmware; changing an MPN suffix alone does not establish that every electrical condition is identical.
Decouple the device supply according to the manufacturer application guidance and keep switching currents away from analog returns. Although the eight switches are individually controlled, simultaneous state changes can produce transient current movement in connected loads and affect sensitive nodes. Add local bulk and high-frequency bypass capacitance, maintain a low-impedance supply path, and test worst-case switching sequences with the intended load attached.
מידע על תאימות
The component information identifies MAX335ENG+ as halogen-free compliant. No explicit RoHS, REACH, lead-free, or conflict-minerals declaration was established, so those fields remain unknown. AEC-Q100 qualification is not stated and is not applicable to the identified commercial analog switch.