MAX3385ECWN - 250kbps True RS-232 Transceiver | Analog Devices
MPN: MAX3385ECWN ✓ פעילMAX3385ECWN סקירה
A true RS-232 transceiver is an interface IC that converts logic-level signals to RS-232 levels and converts incoming RS-232 signals back to logic levels. RS-232 is a point-to-point, unbalanced serial-interface standard widely used for industrial control, data acquisition, instrumentation, and legacy peripheral connections. Its transmitter and receiver circuitry provide the voltage conversion and noise tolerance required when logic levels must communicate with a longer, unbalanced cable.
The MAX3385ECWN supports operation from a single 3.0V to 5.5V supply, allowing use in both 3.3V and 5V systems. Its maximum data rate of 250kbps is suitable for moderate-speed serial links, and the ±15kV ESD rating adds protection for exposed connector pins. The 2/3 driver-receiver configuration is useful when a design requires more receiver channels than transmitter channels.
The MAX3385ECWN family uses integrated true RS-232 line-driver and line-receiver stages rather than a limited-voltage-only interface. This distinction is important when connecting to equipment that expects RS-232 voltage levels. Its operating-temperature range is specified as 0°C to 70°C for the commercial-grade CWN configuration, making it appropriate for equipment intended for controlled indoor or industrial environments within that range.
Typical uses include industrial serial adapters, programmable-logic-controller communication, test and measurement instruments, barcode and data-acquisition equipment, and embedded control systems that retain an RS-232 port. Systems operating at 250kbps should include appropriate cable routing and grounding because unbalanced RS-232 performance can still be affected by ground offsets, electromagnetic interference, and connector cable characteristics.
PCB implementation should follow the manufacturer's pin and decoupling guidance, particularly for supply connections and exposed RS-232 pins. Place the required bypass capacitor close to the device, route transceiver outputs to the connector through a short and appropriately arranged path, and confirm that system grounding satisfies the interface requirements before enabling communication.
This page combines the manufacturer-oriented device identity, verified distributor descriptions, RS-232 design guidance, package details, and replacement analysis. It also identifies where additional electrical, mechanical, and lifecycle information must be confirmed in the manufacturer datasheet or through a current manufacturer quotation.
חלופות תחליף ישיר עבור MAX3385ECWN — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
MAX3384ECWN
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX3385ECWN מפרטים
| Product Type | True RS-232 transceiver |
| Transceiver Configuration | 2 drivers and 3 receivers |
| Supply Voltage Range | 3.0V to 5.5V |
| Nominal Supply Voltage | 3.3V |
| Maximum Data Rate | 250kbps |
| ESD Protection | ±15kV |
| Interface Standard | RS-232 |
| טווח טמפרטורת פעולה | 0°C to 70°C |
| מארז | 18-SOIC |
| Terminal Count | 18 terminals |
| Package Shape | Rectangular |
| Lead Form | Gull wing |
| סוג הרכבה | Surface mount |
| Temperature Grade | Commercial |
מדריך תצורת פינים של MAX3385ECWN rectangular
תצורת פינים עבור MAX3385ECWN (מארזת rectangular). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור MAX3385ECWN.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
MAX3385ECWN מתאים עבור 6 יישוםs: Industrial PLC Serial Communication, Test and Measurement Instrumentation, Data Acquisition Equipment, Embedded Control and Service Interfaces, Legacy Peripheral Connectivity, Barcode and Automation Terminals.
Industrial PLC Serial Communication
The MAX3385ECWN fits legacy programmable-logic-controller and serial-adapter interfaces that require true RS-232 voltage conversion. Its 2-driver, 3-receiver arrangement allows a controller board to communicate through two RS-232 channels while monitoring three incoming signals. Operation from a 3.0V to 5.5V supply supports 3.3V and 5V embedded systems, while the 250kbps maximum data rate suits moderate-speed command and status traffic. The ±15kV ESD rating improves protection at connector-facing circuitry. Designers should keep driver and receiver nets short, provide the required bypass capacitance, and verify the target PLC's logic levels, ground reference, and connector pinout before commissioning.
Test and Measurement Instrumentation
The MAX3385ECWN is appropriate for instruments that retain RS-232 control or data ports alongside modern USB, Ethernet, or embedded interfaces. Two transmitters can support separate command and status links, while three receivers can accept responses from multiple devices. The 250kbps limit is adequate for many configuration and low-volume data-transfer tasks, and the true RS-232 line interface avoids relying on a logic-level-only transceiver. The 3.0V-to-5.5V supply range simplifies integration with mixed-voltage instrument electronics. For reliable operation, separate logic and cable grounds according to the system grounding plan, route exposed RS-232 nets away from sensitive analog sections, and confirm the connected instrument's driver and receiver limits.
Data Acquisition Equipment
The MAX3385ECWN can add RS-232 connectivity to a data-acquisition controller that must exchange commands, status, or sampled data with older laboratory equipment. Its three receivers are useful when the controller must monitor several incoming RS-232 sources, while the two drivers support outbound control paths. The 250kbps data-rate ceiling supports moderate transfer speeds rather than high-volume continuous streaming. A single 3.0V-to-5.5V operating range permits use with both 3.3V and 5V subsystems. Careful grounding is essential because RS-232 is an unbalanced interface, and cable routing should avoid high-current switching nodes. Confirm the remote device's connector wiring and ensure that all attached transmitters use compatible voltage levels.
Embedded Control and Service Interfaces
The MAX3385ECWN is suitable for embedded controllers that must provide a field-service or configuration port using an RS-232 connector. The two-driver and three-receiver arrangement supports bidirectional control plus additional status inputs, and the commercial 0°C-to-70°C range suits equipment operated within controlled indoor environments. Its 250kbps capability is adequate for firmware logs, configuration commands, and routine telemetry. The 3.0V-to-5.5V range allows direct use with common embedded supply levels, reducing the need for a separate interface rail. Designers should provide the manufacturer-recommended supply decoupling, include the required charge-pump components, protect externally accessible lines as required by the system ESD strategy, and validate the complete interface against the service connector's wiring.
Legacy Peripheral Connectivity
The MAX3385ECWN provides a practical interface bridge for embedded systems that must communicate with legacy printers, scanners, scales, or other RS-232 peripherals. Two transmitter channels can serve separate peripherals, while three receiver inputs can accommodate additional status or handshake signals. The true RS-232 implementation is important when the peripheral expects standard bipolar line levels rather than logic-level signals. Operation up to 250kbps supports many short-distance control protocols, while the ±15kV ESD rating is valuable where the interface reaches an external connector. Verify each peripheral's data format, baud rate, flow-control method, and pin assignment. The PCB should include adequate connector clearance and a ground strategy that avoids injecting cable or chassis currents into sensitive circuitry.
Barcode and Automation Terminals
The MAX3385ECWN suits barcode scanners, terminal controllers, and automation peripherals that exchange commands and status data through RS-232. Its 250kbps rate is more than sufficient for ordinary scanner configuration, barcode-event transfer, and low-bandwidth machine-control commands. The 3.0V-to-5.5V operating range simplifies use in terminals built with either 3.3V or 5V logic, and the 2/3 driver-receiver arrangement supports communication with several attached devices. The ±15kV ESD protection rating helps manage electrostatic discharge at an exposed equipment port. Engineers should confirm whether the terminal requires hardware handshake lines, implement the recommended charge-pump and bypass networks, and test the complete system with the intended cable length and peripheral grounding arrangement.
נתוני עזר הנדסיים עבור MAX3385ECWN — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MAX3384ECWN |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 18-SOIC | 18-SOIC |
| Device Type | True RS-232 transceiver | RS-232 transceiver |
מבדילים עיקריים
- Receiver-rich 2/3 transceiver configuration (לעומתMAX3384ECWN)
- Clearly defined 250kbps operating ceiling (לעומתMAX3384ECWN)
- ±15kV ESD protection for connector-facing circuits (לעומתMAX3384ECWN)
הערות תכנון
Follow the manufacturer datasheet layout for the charge-pump capacitor, supply bypass, transceiver inputs, outputs, and exposed connector pins. Place the required bypass capacitor immediately across the device supply pins and keep its ground path short. Route each driver output directly toward its RS-232 connector, preserve the manufacturer's recommended component spacing, and avoid placing sensitive analog traces beneath or parallel to the unprotected driver nets.
Do not infer replacement compatibility from the shared 18-SOIC outline. Compare the complete pin-description tables for the MAX3385ECWN and proposed substitute, including driver outputs, receiver inputs, enable or shutdown functions, charge-pump nodes, supply pins, and ground connections. A physical footprint match is necessary but not sufficient; mixed RS-232 and logic signals on the same connector can produce permanent damage if the replacement maps a driver output to a receiver input.
RS-232 uses an unbalanced signal referenced to ground, so system grounding strongly influences noise and communication reliability. Use the application guidance in the manufacturer datasheet to establish chassis, circuit, and signal ground relationships. Keep the transceiver close to the connector, minimize the unprotected driver trace length, provide low-impedance return paths, and test with the intended cable because ground offsets and electromagnetic coupling can alter received voltage and cause intermittent communication errors.
Treat the 250kbps maximum as an upper operating limit rather than a guaranteed rate for every cable, baud rate, and system-ground arrangement. Use the datasheet's driver-load and receiver-threshold specifications when designing the interface. For long cables, electrically noisy machinery, or poorly grounded systems, reduce the communications rate, add compatible filtering where appropriate, and validate signal integrity with an oscilloscope at the connector.
מידע על תאימות
The commercial 0°C-to-70°C grade is not an automotive qualification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from current manufacturer product documentation.