MC3488ADR2 - Dual RS-232/RS-423 Driver | onsemi
MPN: MC3488ADR2 ✓ פעילMC3488ADR2 סקירה
A line driver is an interface IC that converts low-level logic signals into differential or balanced transmission-line signals suitable for driving cable-based communications links. In the broader power-management and signal-chain hierarchy, this device belongs to the interface-IC family rather than a voltage regulator or memory component. It is commonly positioned between a UART, transceiver, or other digital controller and a physical data cable, where it provides the electrical drive required at the transmitter end.
The principal feature of the MC3488ADR2 is its dual-channel configuration, allowing two communications or control links to be supported by one device. The RS-232 and RS-423 labeling means the same packaged driver can be considered for point-to-point RS-232 links and balanced RS-423-style interconnects, subject to the detailed interface requirements of the connected system. Using a single 8-pin IC for two channels can reduce component count and simplify PCB layout compared with separate single-channel drivers.
The MC3488ADR2 is intended for point-to-point, multipoint, or longer-distance interface links where logic-level signals must be transmitted over cables. Suitable equipment includes industrial data acquisition, instrumentation, test and measurement systems, embedded controllers, peripheral interfaces, and legacy computer communications equipment. Because it is a driver rather than a complete transceiver, it does not by itself provide a receive path; the receiving end requires a suitable line receiver or transceiver.
When laying out an MC3488ADR2 circuit, place the device near the connector or cable interface, route each driver output directly to its corresponding connector pin, and maintain a common ground reference for the link where required by the selected EIA interface. Avoid long unprotected PCB traces between the IC and connector, and use the application circuit in the onsemi datasheet to select any external wave-shape-control components. Confirm signal levels, operating temperature, supply voltage, and termination requirements against the complete electrical-characteristics table before releasing production artwork.
This page combines the verified package and interface identification, practical RS-232 and RS-423 use cases, drop-in replacement assessment, and PCB-focused design guidance for engineers evaluating the MC3488ADR2 in new or existing interface designs.
חלופות תחליף ישיר עבור MC3488ADR2 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MC3488ADR2 (אותו גורם צורה וטביעת רגל) — שונים ב Package.
MC3488ADG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MC3488AD
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MC3488ADR2G
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
UA9636ACD
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MC3488ADR2 מפרטים
| Product Type | Dual RS-232/RS-423 line driver |
| Number of Driver Channels | 2 channels |
| Supported Interfaces | RS-232 and RS-423 |
| מארז | 8-SOIC, 3.90 mm width |
| Terminal Count | 8 terminals |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| סוג הרכבה | Surface mount |
| Temperature Grade | Commercial |
מדריך תצורת פינים של MC3488ADR2 rectangular
תצורת פינים עבור MC3488ADR2 (מארזת rectangular). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור MC3488ADR2.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
MC3488ADR2 מתאים עבור 6 יישוםs: Industrial Serial Data Acquisition, Test and Measurement Instrumentation, Legacy Computer Communications, Embedded Control Interfaces, Point-to-Point RS-423 Links, Peripheral and Equipment Interfaces.
Industrial Serial Data Acquisition
The MC3488ADR2 fits dual-channel industrial data-acquisition equipment that sends commands and receives measurement updates over wired serial links. Its two RS-232/RS-423 driver channels allow one controller board to support two independent point-to-point connections without using two separate 8-pin driver packages. Place the IC near the external connectors, route outputs directly to the cable pins, and preserve a short ground return to minimize board-noise pickup. The commercial temperature grade suits controlled indoor equipment, although industrial systems with wider temperature requirements should verify the operating limits against the onsemi datasheet.
מומלץ
Test and Measurement Instrumentation
MC3488ADR2 is appropriate for laboratory instruments that must exchange command and status information with a host computer over an isolated cable interface. Two driver channels can serve separate control and diagnostic connectors, simplifying the transmitter section of the design. Keeping the driver close to the connector shortens vulnerable traces and helps limit edge degradation before signals reach the cable. Designers should verify the selected data rate, logic thresholds, output voltage, and permitted cable loading against the onsemi electrical-characteristics table because those limits are not reproduced in the catalog listing.
מומלץ
Legacy Computer Communications
The MC3488ADR2 is well suited to legacy computer, terminal, and peripheral interfaces that require dedicated RS-232 transmitter channels. It provides a practical bridge between a UART's logic-level outputs and a wired communications connector while leaving receive functions to a separate receiver or transceiver. Using both driver channels in one package reduces PCB area compared with two single-channel solutions. Verify connector pin assignments, signal polarity, cable length, and grounding before connecting the board, and avoid assuming that a line driver alone provides the complete bidirectional interface.
מומלץ
Embedded Control Interfaces
MC3488ADR2 can provide the physical transmitter layer for an embedded controller that communicates with remotely located modules, service equipment, or industrial peripherals. The dual-channel arrangement supports separate command and status paths over point-to-point connections, while its compact 8-SOIC outline simplifies routing on a control board. The device should be positioned close to the connector, with output traces kept short and the ground reference routed as part of the controlled interface. Confirm supply voltage, input logic compatibility, enable behavior, and maximum signaling rate in the manufacturer documentation before interface implementation.
מומלץ
Point-to-Point RS-423 Links
MC3488ADR2 supports point-to-point RS-423-style communications where balanced driver outputs are preferred for noise immunity over longer cable runs. Two channels can serve independent equipment links or a bidirectional arrangement when paired with suitable receiving circuitry. The driver should be placed near the connector, and any receiver termination must follow the selected EIA interface recommendation rather than be copied from an unrelated RS-232 design. Because RS-423 behavior depends on cable length, loading, grounding, and common-mode limits, evaluate the complete link against the datasheet and applicable interface requirements.
מומלץ
Peripheral and Equipment Interfaces
The MC3488ADR2 can drive wired command links in printers, scanners, programmable instruments, and other peripheral equipment. Integrating two transmitters in one 8-SOIC package simplifies synchronization and reduces the number of line-driver footprints on the PCB. Connect each driver output to the corresponding connector contact and keep the device close to the interface entry point to limit pickup on the PCB. Designers should also confirm whether the target equipment requires RS-232, RS-423, or a vendor-specific voltage convention because the connector protocol and the driver's electrical operating limits must be checked together.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MC3488ADR2 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MC3488ADG | MC3488AD | MC3488ADR2G | UA9636ACD |
|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | SOIC-8 |
| Brand | onsemi | onsemi | onsemi | onsemi | Texas Instruments |
| Driver Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Interface Class | RS-232/RS-423 | RS-232/RS-423 | RS-232/RS-423 | RS-232/RS-423 | RS-232/EIA-423 |
| Terminal Count | 8 terminals | 8 terminals | 8 terminals | 8 terminals | 8 pins |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
| Special Ordering Feature | MC3488ADR2 ordering suffix | ADG ordering suffix | AD ordering suffix | R2G ordering suffix | CD ordering suffix |
מבדילים עיקריים
- Two independent driver channels in one 8-SOIC device (לעומתMC3488ADG)
- Direct onsemi family alternative with matching package class (לעומתMC3488AD)
- Cross-brand option identified in an 8-pin package (לעומתUA9636ACD)
- Exact onsemi ordering configuration (לעומתMC3488ADR2G)
הערות תכנון
Place the MC3488ADR2 close to the cable connector and route each driver output directly to the corresponding connector pin. Keep the interface ground return short and continuous, avoid long traces through the digital portion of the PCB, and provide a common reference between communicating systems where required by the selected RS-232 or RS-423 topology. Short output paths reduce radiated coupling and susceptibility to switching noise before the signal enters the cable.
Confirm the onsemi electrical table for output levels, input thresholds, slew behavior, and the maximum supported data rate before selecting resistor values or cable length. A nominal RS-232 or RS-423 label alone does not guarantee interoperability with every receiver. Check the complete link, including receiver loading, termination, grounding, cable characteristics, and any external wave-shape-control component shown in the manufacturer application circuit.
Do not treat MC3488ADR2 as a complete transceiver: it provides driver outputs and requires a separate receiver or transceiver for incoming data. Also verify whether a required enable, shutdown, or control terminal is present and properly connected for the selected ordering configuration. Before substituting an 8-pin alternative, compare the pin table position by position rather than relying only on the package outline.
Decouple the device according to the onsemi application circuit, placing the required capacitor as close as practical to the supply and ground pins. Maintain a low-impedance ground plane and avoid routing return current through the long interface-output region. Because the verified catalog does not provide the complete supply-voltage and current limits, confirm those values in the datasheet before selecting the regulator, bulk capacitance, or power-sequencing arrangement.
מידע על תאימות
The verified catalog identifies a commercial-grade interface IC but does not state its RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. The MC3488ADR2G suffix is distinguishable from MC3488ADR2, but its exact compliance declaration requires the onsemi documentation.