MC9S08PL8SCTG - 8-Bit 20MHz S08 MCU, 8KB Flash, 16-TSSOP | NXP
MPN: MC9S08PL8SCTG ✓ פעילMC9S08PL8SCTG סקירה
An 8-bit microcontroller is a microprocessor whose internal data path and registers are 8 bits wide. The S08 family from NXP is a cost-optimised 8-bit core with a Harvard-style architecture, a fast 20 MHz clock, on-chip debug support and an instruction set inherited from the long-established HCS08 lineage. In the system hierarchy, an MCU sits below a microprocessor because it integrates flash, RAM, ADC, timers and serial interfaces onto a single die, so one chip can run a complete control loop without supporting glue logic.
Key features of the MC9S08PL8SCTG include a 10-bit successive-approximation ADC, an integrated analog comparator for threshold and zero-cross detection, flexible timer modules for periodic and capture/compare work, and a 14-pin GPIO budget. The NXP S08PLS family is specifically aimed at 5 V cost-sensitive designs and provides strong EFT and ESD robustness, which matters in motor-control and appliance products where cables behave as antennas.
Technically, the device combines 8K x 8 bytes of flash for program storage with 1 kB of RAM for working data. The 20 MHz maximum clock rate gives roughly 10 MIPS of core throughput, enough for proportional control loops, sensor fusion at modest rates, and simple serial protocol handling. Because the ADC shares the same supply reference as the rest of the chip, accuracy depends on clean decoupling of the VDD pins and a stable reference on the analog side of the board.
Typical applications include temperature controllers in appliances, battery-powered sensor nodes with light duty-cycling, small motor and solenoid drivers, LED lighting controllers, and industrial HMI panels that need a handful of buttons, a display interface and a serial link to a host processor. The 16-TSSOP footprint keeps the board area small enough for compact appliances and handheld instruments.
When laying out a design around this part, treat the analog supply and the digital ground return as separate paths, place 100 nF ceramic bypass capacitors on every VDD pin, and route the ADC input away from switching nodes. Because flash program and erase cycles stall the CPU, structure time-critical loops to run from RAM when response time is critical.
This page brings together manufacturer specifications, drop-in alternatives within the S08 family, a parameter-by-parameter comparison and practical layout guidance that the datasheet alone does not present side by side.
חלופות תחליף ישיר עבור MC9S08PL8SCTG — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MC9S08PL8SCTG (אותו גורם צורה וטביעת רגל) — שונים ב ADC, Mounting Type, Package, Analog Comparator, Interrupt Sources.
MC9S08PL8SCT
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
MC9S08SH8CTG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MC9S08PL4CTG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MC9S08PL4SCT
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
MC9S08SH4CTG
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←MC9S08SH1CTG
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
MC9S08PL8SCTG דירוגים מרביים ומאפיינים חשמליים
| Core / CPU | S08, 8-bit |
| תדר שעון מקסימלי | 20 MHz |
| Flash Memory Size | 8 KB (8K x 8) |
| SRAM Size | 1 kB |
| ADC Resolution | 10 bit |
| Number of I/O Pins | 14 |
| רוחב אפיק נתונים | 8 bit |
| מתח אספקה פעיל | 2.7 V to 5.5 V |
| טמפרטורת פעולה | -40 C to +85 C |
| מארז | 16-TSSOP |
| סוג הרכבה | SMD / SMT |
| Integrated Analog Comparator | Yes |
| רמת רגישות ללחות (MSL) | 3 |
| Peak Reflow Temperature | 260 C |
| Time At Peak Reflow Temperature | 40 s |
| סטטוס מחזור חיים | Active |
מדריך תצורת פינים של MC9S08PL8SCTG 16-tssop
תצורת פינים עבור MC9S08PL8SCTG (מארזת 16-tssop). מעגל משולב דיגיטלי זה כולל GPIO, ממשקי תקשורת (UART, SPI, I2C) ופיני מתח. יש לעיין בגיליון הנתונים של היצרן לפונקציות פינים חלופיות ולאפשרויות תצורה. חיוני לתכנון מערכות משובצות ולפריסת PCB.
אין נתוני פריסת פינים מפורטים עבור MC9S08PL8SCTG.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
MC9S08PL8SCTG מתאים עבור 6 יישוםs: Appliance Control Board, Battery-Powered Sensor Node, LED Lighting Controller, Motor and Solenoid Driver, Industrial HMI and Keypad Front Panel, Portable Instrument and Data Logger.
Appliance Control Board
The MC9S08PL8SCTG suits appliance control boards where a relay, a thermistor and a small display must be coordinated from one low-cost device. Its 10-bit ADC reads the thermistor directly, the analog comparator provides an independent over-temperature trip path that keeps working even if the firmware stalls, and the flexible timer modules generate the zero-cross or PWM drive for the load. Eight kilobytes of flash is ample for a state machine plus a lookup table, and the 2.7 V to 5.5 V operating range accepts either a rectified 5 V rail or a regulated 3.3 V supply. Place the MCU next to the power entry so the supply decoupling is short and the board area stays compact.
מומלץ
Battery-Powered Sensor Node
For a coin-cell or AA powered sensor node, the MC9S08PL8SCTG offers a 1 kB RAM buffer, 14 available I/O pins and a 2.7 V lower operating limit that matches primary-cell chemistry without a boost stage. Run the core from the lowest internal bus divider that still meets the sampling interval, and wake the part from a periodic timer interrupt so the average current stays dominated by sensor and radio activity rather than the MCU. The 20 MHz ceiling means a short duty-cycled acquisition window is available on wake, and the analog comparator can be used as a low-power threshold detector to avoid running a full ADC conversion on every wake-up cycle.
מומלץ
LED Lighting Controller
An LED lighting controller benefits from the MC9S08PL8SCTG's timer modules, which can generate the PWM dimming waveform and the blanking interval without software bit-banging overhead. The 10-bit ADC lets the product implement constant-current regulation or ambient-light compensation, while the 14 I/O pins drive the LED string enables, mode button and fault indicator. Because the part runs from a single 5 V rail with a 2.7 V floor, it can sit directly behind the bridge rectifier and bulk capacitor of a driver board. Keep the PWM output routed away from the ADC input to avoid coupling dimming ripple into the current-sense measurement.
מומלץ
Motor and Solenoid Driver
The MC9S08PL8SCTG is a reasonable fit for small motor and solenoid control in appliances and instrumentation, where a full 32-bit MCU would be overkill. The analog comparator detects rotor or valve position without occupying the ADC, and the timer modules provide the periodic current-measurement window used in a simple closed-loop current regulator. The family's documented EFT and ESD robustness is valuable here, since motor wiring acts as an antenna and induced transients are common. Provide bulk decoupling close to the 16-pin TSSOP footprint, and place a flyback path and snubber away from the MCU ground so switching energy does not share the quiet analog return.
מומלץ
Industrial HMI and Keypad Front Panel
For a compact human-machine interface front panel with a keypad, LED indicators and a link to a host controller, the MC9S08PL8SCTG provides enough GPIO and code space in a small footprint. Debounce and key scanning can be handled with the timer interrupt at 20 MHz, and the 8 KB flash budget comfortably holds the scan table, symbol font subset and a simple state machine. The -40 C to +85 C operating range suits industrial panel environments with temperature cycling. Use the Request a Quote form on this page for current availability of the 16-TSSOP variant, and specify whether you need tape-and-reel or tray packing for your assembly process.
מומלץ
Portable Instrument and Data Logger
Handheld instruments and simple data loggers benefit from the MC9S08PL8SCTG's small TSSOP footprint, wide supply tolerance and low component count. The 1 kB RAM is enough to buffer a block of 10-bit samples before writing to non-volatile storage, and the 20 MHz core leaves headroom for CRC calculation on each record. Because the part operates down to 2.7 V, it can share a battery-derived 3.3 V rail with a radio or sensor module rather than needing its own regulator. Design the layout so the analog sensor input enters the MCU through a dedicated, quiet trace, and keep the flash write regions away from that path to avoid disturbance during program operations.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MC9S08PL8SCTG — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MC9S08PL8SCT | MC9S08SH8CTG | MC9S08PL4CTG | MC9S08SH4CTG |
|---|---|---|---|---|---|
| Package | 16-TSSOP | 16-TSSOP - same | 16-TSSOP - same | 16-TSSOP - same | 16-TSSOP - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Flash Memory | 8 KB (8K x 8) | 8 KB | 8 KB | 4 KB | 4 KB |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| ADC Resolution | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit |
| Number of I/O Pins | 14 | 14 | 14 | 14 | 14 |
| Operating Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
מבדילים עיקריים
- Largest program memory in the pin-compatible 16-TSSOP set (לעומתMC9S08PL4CTG)
- Cost-oriented peripheral mix without serial overhead (לעומתMC9S08SH8CTG)
- Second-source friendly within the S08 footprint (לעומתMC9S08PL8SCT)
הערות תכנון
The MC9S08PL8SCTG accepts a single 2.7 V to 5.5 V supply, so tie every VDD terminal to the same rail and place a 100 nF ceramic bypass capacitor as close as possible to each supply pin, with the ground return taken from the capacitor rather than from a distant plane point. If the board also carries a motor, relay or display backlight, keep that load on a separate branch with its own bulk capacitance so brownout on the high-current path does not trip a reset on the MCU. Brownout during a flash write is the classic cause of corrupted configuration data in appliance boards.
Route the analog input and the comparator sense line as a short trace directly to the MCU pin, with a return path alongside it on the ground plane, and keep switching-node copper (MOSFET drains, relay contacts, LED anode paths) on the opposite side of the board. Do not run analog traces under the TSSOP footprint, and avoid placing the 16-TSSOP near the board edge where cable or transformer leakage couples in. Grounding the exposed analog reference cleanly and filtering the supply with a ferrite bead plus bulk capacitance typically buys more usable ADC accuracy than any software averaging.
Two errors dominate S08 designs. First, flash program and erase cycles block the CPU, so any control loop with a tight response window must run from RAM during that interval. Second, the part is only specified to 5.5 V maximum supply; connecting an unregulated 12 V or 24 V rail directly to a VDD pin destroys the device. Use the resistor divider and comparator inputs for over-voltage detection rather than a rail that exceeds the absolute maximum, and confirm the pin assignment of any comparator input from the family data sheet before assuming the default port mapping.
מידע על תאימות
The NXP product page lists MC9S08PL8SCTG as Active. Reflow handling per the component listing: MSL 3, peak reflow temperature 260 C for up to 40 s. RoHS, REACH and halogen-free declarations are not stated on the sources reviewed, so they are recorded as unknown; confirm with the manufacturer declaration before release to market.