Microchip Technology

MCP3422A0-E/MS - 18-Bit, 2-Ch ADC | Microchip | Sensor

MPN: MCP3422A0-E/MS ✓ פעיל
2.7 V to 5.5 V Vdss 145 µA Id 8-pin MSOP, 3 mm x 3 mm x 0.85 mm Package
כמות הזמנה מינימלית: 1 |

MCP3422A0-E/MS סקירה

The Microchip Technology MCP3422A0-E/MS is a two-channel, 18-bit delta-sigma analog-to-digital converter with differential inputs, a 3.75 samples-per-second conversion rate, and an 8-pin MSOP package measuring 3 mm x 3 mm x 0.85 mm. It operates from 2.7 V to 5.5 V and features an onboard precision 2.048 V reference, allowing a nominal differential input range of ±2.048 V.

A delta-sigma ADC is a type of analog-to-digital converter that uses continuous-time oversampling, noise shaping, and digital filtering to produce high-resolution conversion results. In the electronic-component hierarchy, this MCP3422 belongs to the ADC family, which sits within data-converter and signal-chain ICs. It is intended for low-frequency measurements where high resolution, differential input capability, and simple serial control are more important than rapid sampling.

The MCP3422A0-E/MS provides up to 18 bits of resolution across two analog input channels. Differential inputs reduce sensitivity to common-mode noise when the measured signal is applied between an AIN+ and AIN- terminal. The precision 2.048 V internal reference simplifies ratiometric or direct measurement designs by removing the need for an external reference source. The 3.75 SPS rate supports slowly changing process, temperature, pressure, and bridge-sensor signals rather than waveform capture.

Communication uses a two-wire I2C serial interface, which allows the converter to share pins with a host microcontroller or digital sensor hub. A nominal supply current of 145 µA supports low-power instrumentation, while the 2.7 V to 5.5 V operating range covers common 3.3 V and 5 V systems. The converter is designed for surface-mount assembly in compact industrial, medical, environmental, and precision measurement equipment.

Typical uses include pressure-transducer monitoring, thermistor bridges, current-shunt measurements, laboratory instrumentation, and low-rate data acquisition. Differential excitation and reference-based scaling can improve immunity to ground offsets and supply ripple, although the selected input and conversion settings must remain within the ADC’s electrical limits.

For layout, route analog inputs as short, guarded traces away from switching nodes and digital clock lines. Place the device close to its reference and decoupling network, use a quiet ground-plane arrangement, and provide input filtering appropriate to the source impedance. The slow conversion rate creates timing headroom but requires correct sampling and digital-filter configuration for stable measurements.

This product page combines the manufacturer specifications, application-oriented design guidance, package and pin information, and same-footprint replacement analysis. It also explains the electrical trade-offs involved when selecting the MCP3422A0-E/MS for slow, high-resolution differential measurements.

חלופות תחליף ישיר עבור MCP3422A0-E/MS — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם MCP3422A0-E/MS (אותו גורם צורה וטביעת רגל) — שונים ב Differential Input Range, Package, Resolution.

Microchip Technology
Differential Input Range: -2.048 V to +2.048 V
Package: 8-pin MSOP
Resolution: 18 bit

MCP3422A1T-E/MS

✅ Drop-In
📦 8-pin MSOP
Same-family 8-pin MSOP footprint and 18-bit dual-channel architecture; A1 conversion option differs from the A0 option, with acquisition timing requiring verification.

📋 חלופה להתייחסות (לא בקטלוג)

MCP3422A4-E/MS

✅ Drop-In
Microchip Technology
📦 8-pin MSOP
18 bit · 2 channels · 2 differential inputs · 1 sigma-delta ADC · 3.75 samples/s · 2.048 V · -2.048 V to +2.048 V · 2.7 V to 5.5 V

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

MCP3422A4T-E/MS

✅ Drop-In
📦 8-pin MSOP
Shares the 8-pin MSOP footprint and MCP3422 family functions; A4T acquisition option differs from A0 and requires register and timing verification.

📋 חלופה להתייחסות (לא בקטלוג)

MCP3422A5-E/MS

✅ Drop-In
📦 8-pin MSOP
Uses the same 8-pin MSOP footprint and 18-bit converter family; A5 conversion behavior differs from A0 and must be matched to the required settling time.

📋 חלופה להתייחסות (לא בקטלוג)

MCP3424A0-E/MS

✅ Drop-In ⚠️ מפרטים לא מאומתים
📦 8-pin MSOP
Shares the 8-pin MSOP footprint, two differential channels, and 18-bit delta-sigma architecture; MCP3424-specific conversion and register behavior must be checked.

📋 חלופה להתייחסות (לא בקטלוג)

MCP3422A0-E/MS דירוגים מרביים ומאפיינים חשמליים

ADC Type Delta-sigma (ΔΣ)
רזולוציה Up to 18 bits
Number of Channels 2 channels
Input Architecture 2 differential inputs
קצב דגימה 3.75 samples/s
Supply Voltage Range 2.7 V to 5.5 V
Nominal Supply Current 145 µA
Internal Reference Voltage 2.048 V
Differential Input Range ±2.048 V
Input Polarity Bipolar differential
Serial Interface I2C, 2-wire
מארז 8-pin MSOP, 3 mm x 3 mm x 0.85 mm
סוג הרכבה Surface mount
Product Type Low-noise, high-accuracy ADC
Onboard Reference Yes

תצורת פינים של MCP3422A0-E/MS

MSOP-8 Package Pinout Diagram MSOP-8 3x3mm, P0.65mm, JEDEC MO-187. 1 8 2 7 3 6 4 5 MSOP-8
פין 1 AIN0+ — Positive input for analog channel 0
פין 2 AIN0- — Negative input for analog channel 0
פין 3 AIN1+ — Positive input for analog channel 1
פין 4 AIN1- — Negative input for analog channel 1
פין 5 SCL — I2C clock input
פין 6 SDA — I2C bidirectional data input and output
פין 7 VDD — Positive supply voltage
פין 8 VSS — Ground reference

יישומים טיפוסיים

MCP3422A0-E/MS מתאים עבור 6 יישוםs: Pressure Transducer Monitoring, Temperature and Thermistor Bridge Acquisition, Current-Shunt Measurement, Environmental and IoT Sensor Hubs, Medical Instrument Signal Monitoring, Laboratory Data Acquisition.

🏭

Pressure Transducer Monitoring

The MCP3422A0-E/MS fits low-rate bridge-pressure measurements where two differential inputs can monitor separate transducers or a differential sensor pair. Its differential input architecture rejects common-mode signals that would otherwise add error to a single-ended measurement, while the onboard 2.048 V reference supports stable scaling. The 18-bit resolution and 3.75 SPS conversion rate are appropriate for slowly changing pressure in industrial equipment. Place the analog traces away from motors and switching supplies, use a dedicated analog ground path, and follow the input-filter and settling sequence in the manufacturer datasheet for reliable transducer excitation and sampling.

🌡️

Temperature and Thermistor Bridge Acquisition

The MCP3422A0-E/MS can acquire two low-rate differential temperature channels with up to 18-bit resolution. The two-channel arrangement allows a sensor bridge and a reference or compensation channel to be digitized through the same interface, reducing duplicated conversion hardware. Its 3.75 samples-per-second rate suits thermal changes measured over seconds or minutes rather than rapid transients. The 145 µA nominal supply current is useful for compact or battery-operated monitoring equipment, while the internal 2.048 V reference simplifies gain calculations when the bridge excitation is stable and appropriately scaled.

⚡

Current-Shunt Measurement

The MCP3422A0-E/MS is suitable for measuring small differential voltages across a current-sense shunt when the voltage remains within the nominal ±2.048 V differential range. Differential sensing reduces the influence of supply noise and ground offsets compared with a single-ended measurement. The 18-bit converter can resolve slow current changes, and two channels permit simultaneous monitoring of a load and a feedback or reference condition. Because the conversion rate is 3.75 samples per second, use this approach for energy, battery, or actuator monitoring rather than high-bandwidth current waveform analysis. Input filtering must preserve the shunt measurement bandwidth.

🧩

Environmental and IoT Sensor Hubs

The MCP3422A0-E/MS fits compact IoT sensor hubs that gather slow differential measurements from environmental or industrial sensors. Its 8-pin 3 mm x 3 mm MSOP package preserves PCB area, while the I2C interface allows the converter to share a two-wire bus with a host microcontroller. A 3.75 samples-per-second rate is appropriate for humidity, gas, soil, or atmospheric sensor outputs that change over seconds. The 2.7 V to 5.5 V operating range supports both 3.3 V and 5 V powered systems, and the 145 µA nominal supply current helps control standby consumption in distributed sensing nodes.

💊

Medical Instrument Signal Monitoring

The MCP3422A0-E/MS can support low-frequency sensing in medical and laboratory instruments when the selected signals fit the ±2.048 V differential range. Two differential channels provide high-resolution measurements from sensors while limiting common-mode interference. The 18-bit resolution and precision 2.048 V onboard reference are useful for bridge-based sensing, while the 3.75 samples-per-second rate matches physiological trends or process variables that do not require high-frequency sampling. Follow medical-device isolation, safety, and calibration requirements as applicable to the finished instrument; the converter’s compliance status alone does not establish system-level approval.

🔧

Laboratory Data Acquisition

The MCP3422A0-E/MS provides a compact two-channel input for laboratory instruments that measure slow voltages with modest sampling requirements. Its differential inputs can reject offset and common-mode voltage present on long sensor connections, while the onboard 2.048 V reference reduces external reference complexity. Up to 18-bit resolution benefits precision measurement, but the 3.75 samples-per-second rate is unsuitable for general-purpose oscilloscope acquisition. Use calibration records, input-overrange protection, and shielding appropriate to the tested source. The I2C interface simplifies connection to an embedded control board while retaining programmable conversion control.

What is the operating voltage of MCP3422A0-E/MS?
The MCP3422A0-E/MS operates from 2.7 V to 5.5 V. According to the Microchip MCP3422 datasheet 22088c.pdf, this range supports common 3.3 V and 5 V systems. The converter has a nominal supply current of 145 µA, making it suitable for compact, low-power measurement equipment when the host circuit can also accommodate the data-acquisition timing.
How many bits and channels does the MCP3422A0-E/MS have?
The MCP3422A0-E/MS provides up to 18-bit resolution across two analog channels. Its two channels use differential inputs, allowing each measurement to be taken between an AIN+ and AIN- terminal rather than from a single signal referenced only to ground. The Microchip manufacturer datasheet identifies the device as a two-channel, low-noise, high-accuracy delta-sigma ADC.
What is the sampling rate of MCP3422A0-E/MS?
The MCP3422A0-E/MS has a sampling rate of 3.75 samples per second. According to the Microchip MCP3422 datasheet 22088c.pdf, the delta-sigma architecture emphasizes resolution and noise performance rather than high-speed waveform acquisition. It is therefore most appropriate for temperature, pressure, bridge, and other slowly changing sensor measurements.
Where can I download the MCP3422A0-E/MS datasheet PDF?
The official MCP3422 family datasheet is available as the Microchip PDF at https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/DataSheets/22088c.pdf. It covers the MCP3422, MCP3423, and MCP3424 devices, including electrical characteristics, operating conditions, digital interface details, and the MSOP pin assignments. Use the manufacturer PDF for the complete specifications and conversion procedure.
Where can I find the MCP3422A0-E/MS pinout?
The MCP3422A0-E/MS pinout is shown in the Microchip MCP3422 datasheet 22088c.pdf, which covers the 8-pin MSOP configuration. The package contains the two differential analog input pairs, the two-wire serial-interface pins, supply, and ground. Confirm the numbered orientation against the package drawing before assigning PCB nets.
What is the internal reference voltage of MCP3422A0-E/MS?
The MCP3422A0-E/MS includes a precision 2.048 V internal reference, enabling a nominal differential input range of ±2.048 V. According to the Microchip product page and MCP3422 datasheet 22088c.pdf, this onboard reference simplifies measurement systems that do not require an external precision reference. Input scaling must still remain within the allowed differential range.
What can replace MCP3422A0-E/MS?
The closest documented replacements are MCP3422A1T-E/MS, MCP3422A4-E/MS, MCP3422A4T-E/MS, MCP3422A5-E/MS, and MCP3424A0-E/MS, all of which use the same-family 8-pin MSOP arrangement. Before replacing the device, verify the conversion option, gain configuration, I2C address, acquisition timing, and register map in the manufacturer datasheet because resolution alone does not guarantee software compatibility.
Is MCP3422A0-E/MS the same as MCP3424A0-E/MS?
The MCP3422A0-E/MS and MCP3424A0-E/MS are closely related two-channel, 18-bit delta-sigma ADCs in the same 8-pin MSOP family, but they are not automatically interchangeable in every design. The Microchip MCP3422/3/4 datasheet groups them as related devices with different conversion characteristics. Verify I2C address, gain settings, conversion timing, and calibration behavior before substituting one for the other.
MCP3422A0-E/MS vs MCP3424A0-E/MS — which is better for sensor measurement?
Choose MCP3422A0-E/MS for a design whose configuration is specifically based on its documented 3.75 SPS conversion behavior and MCP3422 family register map. Consider MCP3424A0-E/MS when its documented conversion and acquisition characteristics better match the required settling time. Both provide two differential channels and up to 18-bit resolution, but software and acquisition timing must be checked against the correct datasheet.
When should I choose MCP3422A0-E/MS over another MCP3422 family member?
Choose MCP3422A0-E/MS when the board specifically targets the MCP3422A0 conversion option and its 3.75 samples-per-second rate is adequate for the measurement. A different MCP3422A-series option may offer a different acquisition profile, so the deciding factors should be conversion time, gain configuration, I2C address, and firmware compatibility rather than package appearance alone.
Is MCP3422A0-E/MS suitable for pressure and temperature sensors?
Yes, the MCP3422A0-E/MS is suitable for pressure and temperature sensors that produce slowly varying differential signals. Its two differential channels can monitor separate bridge or transducer outputs, while the 3.75 samples-per-second rate is appropriate for thermal and pressure changes rather than vibration waveforms. Use the ±2.048 V input range and 145 µA nominal supply current as the initial design constraints.
How does MCP3422A0-E/MS compare with MCP3422A1T-E/MS?
Both devices belong to the Microchip MCP3422 family and are documented in 8-pin MSOP variants, but their conversion-option behavior must be compared before interchangeability is assumed. The MCP3422A0-E/MS is specified at 3.75 samples per second, whereas MCP3422A1T-E/MS is the A1 option with its own documented acquisition profile. Check settling time, gain, I2C address, and register behavior.
Where can I buy MCP3422A0-E/MS with current availability?
Use the Request a Quote form on this page to request current availability, MOQ, and delivery information for MCP3422A0-E/MS. Microchip Direct lists the exact MPN with substantial inventory and incoming factory stock, while the manufacturer product family page supports technical identification. The request form provides a direct purchasing path without embedding a changing price or availability claim in the page copy.
What is the price of MCP3422A0-E/MS?
The current price of MCP3422A0-E/MS should be requested through the Request a Quote form on this page. Pricing can vary with order quantity, procurement schedule, packaging, and current channel availability, so the page’s structured pricing area is the appropriate source for a live commercial response. The form also lets buyers specify quantity and required delivery timing.
What is the lead time and stock status for MCP3422A0-E/MS?
Microchip Direct lists MCP3422A0-E/MS as in stock and also reports incoming factory stock, but a project-specific lead time should be confirmed through the Request a Quote form on this page. Lead time can depend on quantity, date code, packaging format, and whether assembly inventory is reserved from factory stock rather than sold from distributor inventory.
What are the key specifications of MCP3422A0-E/MS that engineers should know?
The MCP3422A0-E/MS is a two-channel, differential-input, 18-bit delta-sigma ADC with a 3.75 samples-per-second conversion rate. It operates from 2.7 V to 5.5 V, draws 145 µA nominally, uses a precision 2.048 V internal reference, and provides a nominal ±2.048 V differential input range. Its I2C interface and 8-pin 3 mm x 3 mm MSOP package suit compact, low-rate acquisition systems.
What is the best cross-brand equivalent for MCP3422A0-E/MS?
No cross-brand drop-in equivalent is established for MCP3422A0-E/MS. A valid replacement must match the 8-pin MSOP footprint, two differential inputs, 18-bit-class resolution, 2.7 V to 5.5 V supply range, 3.75 samples-per-second conversion behavior, I2C interface, and register compatibility. Use the Request a Quote form to discuss a qualified replacement review rather than assuming electrical similarity guarantees drop-in operation.

נתוני עזר הנדסיים עבור MCP3422A0-E/MS — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose MCP3422A0-E/MS for slow, high-resolution differential measurements when the board is designed around its 3.75 samples-per-second A0 conversion behavior, 2.048 V internal reference, and MCP3422-family register interface. MCP3422A1T-E/MS is appropriate when the A1 conversion option better satisfies the required settling time, while MCP3422A4-E/MS and MCP3422A4T-E/MS support systems built around the A4 acquisition profile. MCP3422A5-E/MS is relevant when the A5 timing option fits the measurement. MCP3424A0-E/MS is the closest documented family alternative when its MCP3424-specific conversion behavior is preferred. For every replacement, verify the differential input range, gain settings, I2C address, acquisition timing, filter configuration, and firmware sequence; sharing an 8-pin MSOP footprint alone does not establish complete software compatibility.

השוואה עם חלופות

פרמטר מוצר זה MCP3422A1T-E/MS MCP3422A4-E/MS MCP3422A4T-E/MS MCP3422A5-E/MS MCP3424A0-E/MS
Package 8-pin MSOP, 3 mm x 3 mm x 0.85 mm 8-pin MSOP 8-pin MSOP 8-pin MSOP 8-pin MSOP 8-pin MSOP
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Resolution Up to 18 bits 18-bit family 18-bit family 18-bit family 18-bit family 18-bit family
Number of Channels 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Input Type Differential Differential family architecture Differential family architecture Differential family architecture Differential family architecture Differential family architecture
Internal Reference 2.048 V precision reference Onboard reference Onboard reference Onboard reference Onboard reference Onboard reference
Serial Interface I2C, 2-wire I2C family interface I2C family interface I2C family interface I2C family interface I2C family interface
Supply Voltage Range 2.7 V to 5.5 V 2.7 V to 5.5 V family range 2.7 V to 5.5 V family range 2.7 V to 5.5 V family range 2.7 V to 5.5 V family range 2.7 V to 5.5 V family range
Conversion Option A0 A1T A4 A4T A5 MCP3424A0

מבדילים עיקריים

  • Two differential channels in a compact 8-pin MSOP (לעומתMCP3422A4-E/MS)
  • Onboard precision reference eliminates an external 2.048 V source (לעומתMCP3422A1T-E/MS)
  • Low 145 µA nominal supply current supports compact acquisition systems (לעומתMCP3424A0-E/MS)
  • Direct 2.7 V to 5.5 V operation covers common embedded rails (לעומתMCP3422A5-E/MS)

הערות תכנון

Keep the AIN+ and AIN- traces short, matched where practical, and routed away from switching-regulator outputs, relays, and high-current motor wiring. Connect each input to its source through the filtering network recommended in the manufacturer datasheet. A continuous ground plane provides a low-impedance return path, while guarding and shielding are important when cable-connected sensors can introduce more than 100 mV of noise.

Do not treat the 3.75 samples-per-second conversion rate as a waveform-acquisition bandwidth. Allow the converter to complete its programmed acquisition and conversion sequence before reading a result, and do not change the gain or input configuration while a conversion is active. Verify the differential voltage at the pins remains within ±2.048 V; using the larger common-mode voltage as the input limit can permanently damage the analog inputs.

Place the device close to its decoupling and analog input components, and keep the I2C clock and data routing away from the sensitive AIN+ and AIN- paths. Provide a clean return beneath or beside the analog section and use the manufacturer’s pin-description table when assigning the eight MSOP nets. For long sensor cables, use twisted-pair routing, shield grounding according to the cable arrangement, and input filters sized for the intended source impedance.

The delta-sigma digital filter suppresses noise but does not eliminate errors caused by unsuitable source impedance or settling time. Confirm that the sensor output can charge the selected input capacitor during the available acquisition period. For ratiometric bridges, keep excitation and reference paths together so supply and temperature variations cancel as intended; for absolute measurements, include the 2.048 V internal reference in the calibration procedure.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The exact MCP3422A0-E/MS ordering code has not been identified as automotive-grade in the manufacturer information reviewed. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation for the exact suffix before release.

חיפושים קשורים

MCP3422A0-E/MS datasheet MCP3422A0-E/MS pinout MCP3422A0-E/MS datasheet pdf MCP3422A0-E/MS equivalent MCP3422A0-E/MS replacement MCP3422A0-E/MS price MCP3422A0-E/MS stock MCP3422A0-E/MS vs MCP3424A0-E/MS MCP3422A0 18-bit ADC MCP3422A0 3.75 SPS MCP3422A0 2.048V reference MCP3422A0 MSOP application circuit Microchip MCP3422A0-E/MS

רכיבים ומונחים קשורים

Microchip Technology MCP3422A0-E/MS MCP3422A1T-E/MS MCP3422A4-E/MS MCP3422A4T-E/MS MCP3422A5-E/MS MCP3424A0-E/MS delta-sigma ADC analog-to-digital converter data converter signal-chain IC semiconductor I2C two-wire serial interface differential input 18-bit resolution 3.75 samples per second 2.048 V precision reference 145 µA supply current 8-pin MSOP MSOP package family surface-mount package pressure transducer thermistor bridge current shunt
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר