MCP6002-I/MS - Dual 1MHz Rail-to-Rail Op Amp | Microchip
MPN: MCP6002-I/MS ✓ פעילMCP6002-I/MS סקירה
An operational amplifier is an active analog circuit element that uses high-gain differential amplification to process signals between its supply rails. The MCP6002 belongs to the operational-amplifier hierarchy and combines rail-to-rail signal handling with a typical quiescent current of 100 microamperes. These characteristics make the device applicable to battery-powered instruments, sensor interfaces, audio and communication paths, and other systems operating from low-voltage rails.
The MCP6002 provides two amplifier channels in one package, reducing board area compared with two separate single amplifiers. Rail-to-rail inputs allow signals to use most of the available supply-voltage range, while rail-to-rail outputs improve output swing. Its 1 MHz typical gain-bandwidth product supports general-purpose amplification, and its 100 microampere typical quiescent current helps limit supply consumption in portable equipment.
Both channels share a common supply architecture, making the MCP6002 suitable for matched signal-processing stages such as instrumentation amplifiers, filters, and differential front ends. The operating range of 1.8 V to 6 V covers common low-voltage supply systems. Because the MCP6002 is a general-purpose amplifier rather than a precision or high-speed device, applications requiring very low offset voltage, very high bandwidth, or extended supply voltage should use a more specialized amplifier family.
Typical uses include battery-operated sensor acquisition, low-voltage audio signal conditioning, industrial control interfaces, communications equipment, and portable measurement systems. In a current-sense or transducer interface, the amplifier can operate directly from a low-voltage rail while accepting signals near either rail. In an active filter or gain stage, the 1 MHz bandwidth should be checked against the required closed-loop bandwidth and stability margin.
PCB implementation should place input and output components close to their associated pins, maintain short feedback paths, and provide adequate ground-plane continuity. Because rail-to-rail operation does not guarantee equally precise behavior throughout the entire input range, designers should evaluate signal levels, common-mode voltage, output load, and required accuracy against the manufacturer's recommended application conditions.
This product page consolidates the manufacturer specifications, package information, pricing evidence, available drop-in candidates, and practical design guidance for the MCP6002-I/MS. It supports faster engineering selection by separating known device characteristics from parameters that require confirmation in the manufacturer datasheet.
חלופות תחליף ישיר עבור MCP6002-I/MS — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MCP6002-I/MS (אותו גורם צורה וטביעת רגל) — שונים ב Input Common-Mode Range, Output Swing, Product Type, Supply Voltage Range.
MCP6002-E/MS
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MCP6002-I/MS דירוגים מרביים ומאפיינים חשמליים
| Product Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Supply Voltage Range | 1.8 V to 6 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Gain-Bandwidth Product | 1 MHz typical |
| זרם מנוחה | 100 microamperes typical |
| מארז | 8-lead MSOP |
| סוג הרכבה | Surface mount |
| Application Category | General-purpose amplifier |
מדריך תצורת פינים של MCP6002-I/MS 8-lead msop
תצורת פינים עבור MCP6002-I/MS (מארזת 8-lead msop). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור MCP6002-I/MS.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
MCP6002-I/MS מתאים עבור 6 יישוםs: Battery-Powered Sensor Acquisition, Low-Voltage Audio Signal Conditioning, Industrial Control Signal Interface, Portable Measurement and Instrumentation, Low-Power Communications Buffering, Portable IoT Sensor Node.
Battery-Powered Sensor Acquisition
The MCP6002-I/MS fits low-voltage sensor front ends because its 1.8 V to 6 V supply range permits operation from compact battery rails and its 100 microampere typical quiescent current helps control static demand. Rail-to-rail input capability allows the amplifier to accept sensor signals near either supply rail, while rail-to-rail output improves utilization of the available signal range. It can buffer resistive sensors or form the active stage of a low-frequency instrumentation interface. The 1 MHz typical gain-bandwidth product is suitable for moderate-bandwidth sensor signals, but the design should verify offset, bias-current effects, noise, and settling behavior before using it with high-impedance sources.
מומלץ
Low-Voltage Audio Signal Conditioning
The MCP6002-I/MS can condition line-level or low-level audio signals in portable equipment operating from 1.8 V to 6 V. Rail-to-rail input and output stages provide useful swing on low-voltage rails, and the dual configuration supports paired processing stages without requiring two packages. Its 1 MHz typical gain-bandwidth product is suitable for general audio bandwidth and buffering rather than high-fidelity wideband amplification. Designers should verify output drive into the intended load, input/output distortion, channel matching, and noise performance. The 100 microampere typical quiescent current also helps when battery life is important, although total current depends on load and operating mode.
מומלץ
Industrial Control Signal Interface
The MCP6002-I/MS is suitable for general-purpose signal conditioning in compact industrial control systems where the field interface operates from a low-voltage rail. Two independent channels can amplify sensor outputs, buffer control signals, or form active filter stages within one 8-lead MSOP package. Rail-to-rail input and output behavior helps preserve signal range, while the 1 MHz typical bandwidth supports many control and instrumentation tasks. For factory equipment, confirm the exact operating-temperature requirement and relevant industrial qualification before deployment. The 100 microampere typical quiescent current is advantageous in distributed low-power nodes, but grounding and isolation remain critical when handling noisy motors, relays, or long sensor cables.
מומלץ
Portable Measurement and Instrumentation
The MCP6002-I/MS supports compact measurement instruments that combine two analog channels with a low-voltage supply. It can implement non-inverting and inverting gain stages, buffers, active filters, and differential input arrangements around the same dual package. The 1 MHz typical gain-bandwidth product provides moderate signal bandwidth, and the 100 microampere typical quiescent current is useful in handheld equipment. Rail-to-rail operation allows greater input and output range than a fixed common-mode amplifier at low supply voltages. Engineering checks should include resistor-generated noise, amplifier offset, input bias current, load stability, and the settling response required by the measurement bandwidth. A grounded, uninterrupted return path is especially important when processing low-level transducer signals.
מומלץ
Low-Power Communications Buffering
The MCP6002-I/MS can be used for low-speed communications-interface buffering in portable or distributed systems supplied from a 1.8 V to 6 V rail. Rail-to-rail inputs accommodate logic-level signals close to the supply limits, and rail-to-rail outputs provide improved drive range for downstream digital or analog circuitry. The 1 MHz typical gain-bandwidth product is adequate for many low-rate buffers, though protocol rise-time and bandwidth requirements must be checked. Low quiescent current of 100 microamperes typical helps suit always-on equipment. Board layout should minimize trace capacitance and provide a solid ground reference, while input and output paths should be separated from fast switching nodes to reduce coupling and data errors.
מומלץ
Portable IoT Sensor Node
The MCP6002-I/MS is appropriate for analog conditioning within a compact IoT sensor node because its 1.8 V minimum supply and 100 microampere typical quiescent current align with low-energy designs. The dual channel count supports buffering or gain stages associated with two sensors, while the 8-lead MSOP package preserves board area. Rail-to-rail operation can improve signal utilization on cells or low-voltage regulators, but input offset and noise may become important when resolving small sensor outputs. Select external resistor networks and capacitors for the required bandwidth, keep feedback loops short, and place bypass capacitance close to the supply pins. For systems operating from a regulated 3.3 V or 5 V rail, verify the total amplifier and load current against the power budget.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MCP6002-I/MS — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MCP6002-E/MS |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 8-lead MSOP | 8-lead MSOP |
| Channel Count | 2 channels | 2 channels |
| Supply Voltage Range | 1.8 V to 6 V | 1.8 V to 6 V |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Gain-Bandwidth Product | 1 MHz typical | 1 MHz typical |
| Quiescent Current | 100 microamperes typical | 100 microamperes typical |
| Ordering Grade | I designation | E designation |
מבדילים עיקריים
- Two rail-to-rail amplifier channels in one 8-lead MSOP (לעומתMCP6002-E/MS)
- Operation from low-voltage battery-oriented supply rails (לעומתMCP6002-E/MS)
- Low quiescent current for dual-channel operation (לעומתMCP6002-E/MS)
הערות תכנון
Place the amplifier input, output, feedback-resistor, and compensation components close to the associated MSOP pins. Keep feedback traces short to reduce parasitic capacitance and improve loop stability. Route both amplifier channels with symmetric grounding where channel matching matters, and provide a continuous ground plane beneath the device. Place supply bypass capacitance close to the supply pins and connect it through short, low-inductance paths.
Calculate supply demand from the 100 microampere typical quiescent current plus output-current and dynamic contributions. Rail-to-rail operation does not eliminate the need for adequate supply headroom, and output current still depends on load impedance, output voltage, and frequency. Confirm the regulator can start into the required load and that the MCP6002-I/MS supply remains within 1.8 V to 6 V under worst-case conditions.
Evaluate closed-loop gain against the 1 MHz typical gain-bandwidth product and include the required phase-margin margin in the filter or amplifier design. High-impedance sources require attention to input bias current and capacitance, while capacitive loads may require an isolation resistor. Do not assume rail-to-rail input operation provides identical precision at every common-mode voltage; check the manufacturer's characteristic plots for the signal range of interest.
Do not treat the I and E ordering-grade codes as interchangeable without checking the exact temperature range and qualification requirements. Likewise, a package match alone does not establish full drop-in compatibility. Verify channel pin functions, supply limits, electrical characteristics, and production ordering codes against the manufacturer datasheet. For a new PCB, use the official MSOP land pattern rather than scaling a generic SOIC footprint.
מידע על תאימות
No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement is stated for this ordering code. AEC-Q100 is not applicable to the general-purpose amplifier ordering designation unless the manufacturer documentation explicitly states otherwise.