MCP6007-E/SN - Dual 1MHz RRIO Op Amp | Microchip
MPN: MCP6007-E/SN ✓ פעילMCP6007-E/SN סקירה
An operational amplifier is an analog signal-conditioning IC that uses high-gain differential feedback to amplify, buffer, filter, or isolate signals. The MCP6007 belongs to the broader hierarchy of operational amplifier, analog amplifier, signal-conditioning IC, and semiconductor. Rail-to-rail input operation permits signals to approach the supply limits, while rail-to-rail output improves output swing and makes the device useful in compact, low-voltage sensor and signal-processing systems.
The MCP6007 combines a 1 MHz typical gain-bandwidth product with rail-to-rail input and output capability. Maximum input offset voltage is ±1.6 mV, and maximum quiescent current is 70 µA per amplifier. The device is unity-gain stable and includes EMI filtering, making it suitable for direct sensor conditioning, low-frequency active filtering, voltage buffering, and general-purpose analog signal chains operating from low-voltage supply rails.
Its two amplifiers share the same supply pins but provide independent input and output pins, allowing simultaneous dual-channel signal processing. The 1.9 V/µs typical slew rate supports reasonably clean transitions in low-bandwidth applications. A 1 MHz gain-bandwidth product is more appropriate for precision, low-speed analog functions than for high-speed video, RF, or wideband pulse applications, while the low 70 µA maximum quiescent current per amplifier favors battery-operated equipment.
Typical uses include bridge-amplifier signal conditioning for resistive sensors, active low-pass filters, audio input buffers, portable instrumentation, and low-current sensor interfaces. Because the MCP6007 supports rail-to-rail input and output, it is particularly useful when the signal span is close to the available supply voltage. Supply bypass capacitors close to the power pins remain essential for stable operation in practical layouts.
The primary design trade-off is bandwidth: the 1 MHz gain-bandwidth product limits large-signal response and closed-loop performance at higher frequencies. Designers should also check noise, output-current capability, and stability with the selected feedback network for each gain setting. The E-grade temperature range supports industrial environments, but the SOIC-8 package is larger than modern leadless alternatives.
This page combines the manufacturer’s electrical characteristics with package, sourcing, comparison, and design guidance for engineers evaluating the MCP6007-E/SN in low-voltage dual-amplifier circuits. It also identifies pin-compatible family alternatives and highlights the measured differences that matter when reusing an existing 8-pin SOIC layout.
חלופות תחליף ישיר עבור MCP6007-E/SN — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
MCP6001-E/SN
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
MCP6002-E/SN
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
MCP6004-E/SN
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
MCP6007-E/SNVAO
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MCP6007-E/SN דירוגים מרביים ומאפיינים חשמליים
| Amplifier Count | 2 amplifiers |
| Product Type | General-purpose operational amplifier |
| Gain-Bandwidth Product | 1 MHz typical |
| Slew Rate | 1.9 V/µs typical |
| Minimum Supply Voltage | 1.8 V |
| Maximum Supply Voltage | 5.5 V |
| Input Offset Voltage | ±1.6 mV maximum |
| זרם מנוחה | 70 µA maximum per amplifier |
| Input Common-Mode Range | Rail-to-rail |
| Output Voltage Swing | Rail-to-rail |
| Gain Stability | Unity-gain stable |
| EMI Filtering | Yes |
| טווח טמפרטורת פעולה | -40°C to +125°C |
| מארז | 8-pin SOIC |
| סוג הרכבה | Surface mount |
| סטטוס RoHS | Compliant |
תצורת פינים של MCP6007-E/SN
| פין 1 | OUTA — Operational amplifier A output |
| פין 2 | INA− — Operational amplifier A inverting input |
| פין 3 | INA+ — Operational amplifier A non-inverting input |
| פין 4 | V− — Negative supply or ground connection |
| פין 5 | INB+ — Operational amplifier B non-inverting input |
| פין 6 | INB− — Operational amplifier B inverting input |
| פין 7 | OUTB — Operational amplifier B output |
| פין 8 | V+ — Positive supply connection |
יישומים טיפוסיים
MCP6007-E/SN מתאים עבור 6 יישוםs: Low-Voltage Sensor Signal Conditioning, Portable Battery-Powered Instrumentation, Active Low-Pass Filtering, Audio and Communication Input Buffering, Industrial Control Signal Interfaces, Power-Supply Feedback Buffering.
Low-Voltage Sensor Signal Conditioning
The MCP6007-E/SN suits resistive bridge sensors, temperature sensors, and other low-level differential sources that require two amplifiers in a compact circuit. Its ±1.6 mV maximum input offset voltage helps limit static error, while the 1 MHz gain-bandwidth product provides useful bandwidth for signals well below the kHz range. Rail-to-rail input operation allows the input common-mode voltage to approach the supply limits, which is valuable with 1.8 V to 5.5 V supplies. A common arrangement uses one channel for buffering and gain, and the second channel for gain or filtering. The designer should verify the sensor’s excitation level and the amplifier’s output swing under the intended load.
מומלץ
Portable Battery-Powered Instrumentation
The MCP6007-E/SN is appropriate for handheld meters and battery-operated measurement equipment where each amplifier contributes to a maximum quiescent current of 70 µA. The 1.8 V minimum supply permits operation from low-energy rails, and rail-to-rail input and output improve usable signal range without requiring a higher supply voltage. The two channels can condition two sensor inputs or provide a differential amplifier followed by an output buffer. Because the gain-bandwidth product is 1 MHz typical, the design should limit signal bandwidth and account for noise gain at the selected closed-loop gain. Stable operation also requires the datasheet-recommended supply bypass capacitance and short feedback paths.
מומלץ
Active Low-Pass Filtering
The MCP6007-E/SN can implement active low-pass filters for sensor noise reduction, audio-frequency smoothing, or control-signal conditioning. Its unity-gain stability supports a follower configuration, and the 1 MHz typical gain-bandwidth product allows useful closed-loop bandwidth in low-frequency filter stages. Two independent amplifiers can implement a two-pole filter or separate filtering channels. Component tolerances and the amplifier’s finite gain-bandwidth product influence the actual cutoff and phase response, so simulation with realistic op-amp models is recommended. Decoupling capacitors should be placed directly across the supply pins, while resistor and capacitor connections around the feedback network should remain compact to reduce parasitic coupling.
מומלץ
Audio and Communication Input Buffering
The MCP6007-E/SN can buffer low-level audio or communication inputs when the design operates within the amplifier’s 1 MHz bandwidth and low-frequency signal range. Rail-to-rail input and output operation helps preserve signal amplitude near the supply rails, while the 1.9 V/µs typical slew rate reduces distortion risk for moderate-amplitude waveforms. The dual configuration can drive one active speaker or provide input buffering for two channels. Designers should avoid treating the device as a wideband audio power amplifier; output-current limits, output-voltage swing, and load impedance must be checked against the intended drive level. A small isolation resistor near the output can also limit capacitive-load transients.
מומלץ
Industrial Control Signal Interfaces
The MCP6007-E/SN is suitable for low-speed industrial control boards that interface 0–5 V, 0–3.3 V, or other low-voltage sensor signals. The -40°C to +125°C E-grade temperature range supports extended ambient environments, while the 1.8 V operating limit supports modern low-voltage sensor and control platforms. Rail-to-rail inputs help accommodate signals spanning the working range of the rail, and unity-gain stability simplifies buffering and feedback calculations. For factory equipment, the final design should include protection against transients, ESD, and wiring faults because the amplifier itself is not a surge-protection device. Filtering near the connector and properly positioned bypass capacitors help reduce noise pickup and conducted interference.
מומלץ
Power-Supply Feedback Buffering
The MCP6007-E/SN can buffer a remote or high-impedance feedback signal in a low-power supply-control system. Its 70 µA maximum quiescent current per amplifier minimizes the load placed on the sensed rail, and rail-to-rail input operation improves measurement range near the supply endpoints. One channel can buffer the feedback node while the other performs gain or filtering, simplifying a dual-channel implementation. The 1 MHz typical gain-bandwidth product is adequate for slow regulation loops and supervisory measurements, but it is not intended for high-bandwidth compensation. Feedback-loop stability, injection current, and the output’s ability to remain in its linear region must be checked using the actual regulator topology before replacing a dedicated buffer.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MCP6007-E/SN — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MCP6001-E/SN | MCP6002-E/SN | MCP6004-E/SN | MCP6007-E/SNVAO |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Count | 2 amplifiers | 2 amplifiers | 2 amplifiers | 2 amplifiers | 2 amplifiers |
| Gain-Bandwidth Product | 1 MHz typical | 1 MHz typical | 1 MHz typical | 1 MHz typical | 1 MHz typical |
| Input Offset Voltage | ±1.6 mV maximum | Approximately ±4.5 mV maximum | Approximately ±4.5 mV maximum | Approximately ±3 mV maximum | ±1.6 mV maximum |
| Minimum Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Maximum Supply Voltage | 5.5 V | 5.5 V | 5.5 V | 5.5 V | 5.5 V |
| Input and Output Operation | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
| Quiescent Current | 70 µA maximum per amplifier | 70 µA maximum per amplifier | 70 µA maximum per amplifier | 70 µA maximum per amplifier | 70 µA maximum per amplifier |
| Gain Stability | Unity-gain stable | Unity-gain stable | Unity-gain stable | Unity-gain stable | Unity-gain stable |
מבדילים עיקריים
- Lower maximum input offset voltage (לעומתMCP6004-E/SN)
- Improved offset specification versus the MCP6001 family member (לעומתMCP6001-E/SN)
- Automotive-qualified ordering option without changing the family footprint (לעומתMCP6007-E/SNVAO)
הערות תכנון
Place the supply bypass capacitor immediately between pins 8 and 4, with a short and low-inductance return path to the ground reference. The second amplifier may use the same supply pins, so its bypass connection should also be short. Keep the feedback resistors close to the relevant input pins and avoid routing high-impedance input traces beneath digital clock or switching-node copper. These layout practices reduce supply ripple coupling and parasitic oscillation.
Do not assume that a rail-to-rail input automatically supports every input condition at every supply voltage. Check the input common-mode range, output swing, and load current in the Microchip family datasheet, especially when operating near 1.8 V. Also avoid selecting the amplifier solely by its 1 MHz gain-bandwidth product: the closed-loop bandwidth, noise gain, slew rate, output loading, and temperature must all fit the signal being processed.
For a sensor interface, evaluate the complete error budget rather than offset voltage alone. Include sensor tolerance, resistor mismatch, input bias current, noise, amplifier drift, and ADC accuracy. With a 70 µA maximum quiescent current per amplifier and a 1 MHz typical gain-bandwidth product, the MCP6007-E/SN is best suited to low-speed, low-level analog channels; higher-frequency or source-impedance-sensitive designs may require a different amplifier family.
מידע על תאימות
RoHS compliance is stated in the product listing. The MCP6007-E/SNVAO is the automotive-qualified ordering option. REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated for the standard MCP6007-E/SN and remain unknown.