MCP6023-E/SN - 10MHz RRIO Op Amp | Microchip
MPN: MCP6023-E/SN ✓ פעילMCP6023-E/SN סקירה
An operational amplifier, or op amp, is a high-gain analog building block used in signal-conditioning and feedback systems. Its place in the hierarchy is signal amplifier -> operational amplifier -> analog integrated circuit -> semiconductor. Rather than increasing a signal's power level, an op amp compares its input voltages and drives its output to reduce error within a feedback network. Rail-to-rail input and output operation allows useful signal ranges to extend close to the supply rails.
The MCP6023-E/SN combines several characteristics suited to compact analog circuits. Its 10 MHz gain-bandwidth product supports higher-frequency closed-loop amplification than a low-bandwidth precision amplifier. Its 1.0 mA typical operating current supports portable and low-power designs. Input offset voltage below 0.5 mV helps reduce systematic error in DC-coupled amplifiers, while the rail-to-rail output supports direct drive of modest loads without requiring an output-swing margin as large as that of some conventional amplifiers.
Microchip describes the MCP6023 as a CMOS operational amplifier with low bias current, high open-loop gain, high-speed operation, and rail-to-rail output swing. The chip-select feature adds control useful in multichannel systems where several amplifiers share a supply. CMOS construction is appropriate for battery-operated equipment because it supports low static supply demand, although the complete circuit's energy use also depends on output swing, load, and operating frequency.
Typical uses include sensor-signal conditioning, low-level analog measurement, audio paths, active filtering, and general-purpose gain stages. Its rail-to-rail behavior is particularly useful when signals occupy a substantial portion of the available supply range. Designers should still evaluate closed-loop stability, output-current capability, capacitive-load driving, input common-mode behavior, and system noise rather than treating the 10 MHz gain-bandwidth figure as a direct single-pole operating rate.
For PCB implementation, place the bypass capacitor close to the supply pins and connect the input common-mode reference properly for single-supply operation. Avoid leaving unused inputs floating, and verify whether the chip-select state introduces an output condition that affects feedback-loop startup. Keep sensitive input traces short and away from fast-switching nodes to minimize coupled noise.
This product record combines the manufacturer's core operating characteristics, package identification, sourcing guidance, same-family drop-in options, and practical circuit-selection notes. It supports faster engineering decisions by separating the MCP6023-E/SN's verified attributes from application-specific assumptions and by highlighting the checks required during footprint-compatible replacement.
חלופות תחליף ישיר עבור MCP6023-E/SN — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MCP6023-E/SN (אותו גורם צורה וטביעת רגל) — שונים ב Amplifier Type, Input Offset Voltage, Package.
MCP6023-I/SN
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MCP6023T-E/SN
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MCP6023T-I/SN
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MCP6023-E/SN דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Single operational amplifier |
| Gain-Bandwidth Product | 10 MHz |
| Typical Operating Current | 1.0 mA |
| Input Offset Voltage | <0.5 mV |
| Minimum Supply Voltage | 2.5 V |
| Output Swing | Rail-to-rail |
| Input Type | Rail-to-rail |
| Technology | CMOS |
| Unity-Gain Bandwidth | 10 MHz |
| Shutdown or Chip Select | Chip select |
| מארז | 8-pin SOIC, 0.154 inch body width, 3.90 mm width |
| סוג הרכבה | Surface mount |
מדריך תצורת פינים של MCP6023-E/SN 8-pin soic, 0.154 inch body width, 3.90 mm width
תצורת פינים עבור MCP6023-E/SN (מארזת 8-pin soic, 0.154 inch body width, 3.90 mm width). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור MCP6023-E/SN.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
MCP6023-E/SN מתאים עבור 6 יישוםs: Low-Power Sensor Signal Conditioning, Portable Medical Monitoring, Industrial Sensor Acquisition, Audio Preamplifier Stage, Precision Active Filtering, Battery-Powered Data Acquisition.
Low-Power Sensor Signal Conditioning
MCP6023-E/SN fits low-power sensor front ends that require signal amplification close to the sensor rather than near the system ADC. Its 1.0 mA typical operating current minimizes amplifier contribution to a battery-powered design, while rail-to-rail input and output operation provides useful range in a low-voltage system. The 10 MHz gain-bandwidth product allows the amplifier to serve ordinary active filters and gain stages without relying on a high-bandwidth amplifier in the signal chain. Designers should still verify sensor impedance, input bias current, offset tolerance, noise, and the allowable capacitive loading before finalizing the gain and feedback network.
מומלץ
Portable Medical Monitoring
The MCP6023-E/SN can condition low-level physiological or diagnostic sensor signals in portable monitoring equipment where both supply current and signal range matter. Its 1.0 mA typical operating current leaves more of the power budget for sensors, conversion, and radio transmission, while the rail-to-rail output supports signal chains operating near the available supply limits. The 10 MHz gain-bandwidth product is more than adequate for many slow physiological signals, but medical designs must separately assess offset, noise, leakage, isolation, and electrode-interface requirements. The amplifier must not be treated as a complete medical front end without those signal-chain checks.
מומלץ
Industrial Sensor Acquisition
MCP6023-E/SN is appropriate for buffering industrial sensor outputs when the signal chain requires rail-to-rail swing and a bandwidth above that of a basic precision op amp. The 10 MHz gain-bandwidth product supports general-purpose conditioning, filtering, and gain stages around slow or moderate-speed sensors, while 1.0 mA typical operating current simplifies power budgeting. Because industrial environments can introduce large transients and high-impedance sources, engineers should verify the exact input and output limits, common-mode behavior, noise, and stability. Protection, filtering, grounding, and isolation remain separate design functions and should not be inferred from the amplifier specifications alone.
מומלץ
Audio Preamplifier Stage
MCP6023-E/SN can serve as a general-purpose audio preamplifier or active-filter element in compact line-level and low-level audio circuits. Rail-to-rail output operation increases the usable signal range at low supply voltages, and the 10 MHz gain-bandwidth product gives adequate closed-loop bandwidth for typical audio-band stages. The 1.0 mA typical operating current also suits battery-powered audio equipment. Sound quality still depends on input-referred noise, distortion, output-current capability, load impedance, and layout, so those characteristics require separate verification. The amplifier should be configured with stable feedback and terminated source impedances rather than driving an unspecified reactive load.
מומלץ
Precision Active Filtering
The MCP6023-E/SN is a practical choice for first-order and moderate-order active filters in compact analog systems. Its 10 MHz gain-bandwidth product provides bandwidth relative to filters operating in the audio, control, or low-frequency instrumentation range, and rail-to-rail output behavior helps preserve filter signals at low supply voltages. The typical operating current of 1.0 mA supports efficient multichannel designs. Filter component tolerances, amplifier finite-gain behavior, noise, and stability determine actual response accuracy, so simulation should include expected signal amplitude, load, and frequency rather than using gain-bandwidth product as a simple corner-frequency formula.
מומלץ
Battery-Powered Data Acquisition
MCP6023-E/SN fits battery-powered data-acquisition modules that combine a sensor, amplifier, and converter on a constrained power budget. The amplifier contributes 1.0 mA typical operating current, while rail-to-rail input and output operation reduces the need for an unnecessarily high supply voltage. Its 10 MHz gain-bandwidth product is suitable for buffering many sensors and implementing active anti-alias or signal-conditioning filters. The final design should calculate the complete signal-path power, verify converter input-range compatibility, and account for startup behavior of the chip-select function. This approach maximizes useful rail utilization without changing the required system measurement accuracy.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MCP6023-E/SN — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MCP6023-I/SN | MCP6023T-E/SN | MCP6023T-I/SN |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-pin SOIC | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same |
| Amplifier Type | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier |
| Gain-Bandwidth Product | 10 MHz | 10 MHz | 10 MHz | 10 MHz |
| Typical Operating Current | 1.0 mA | 1.0 mA | 1.0 mA | 1.0 mA |
| Input Offset Voltage | <0.5 mV | <0.5 mV | <0.5 mV | <0.5 mV |
| Minimum Supply Voltage | 2.5 V | 2.5 V | 2.5 V | 2.5 V |
| Input and Output Operation | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Technology | CMOS | CMOS | CMOS | CMOS |
| Ordering-Code Difference | MCP6023-E/SN | I temperature-grade suffix | T production-packaging suffix | T production-packaging and I temperature-grade suffixes |
מבדילים עיקריים
- Combines low supply current with useful signal bandwidth (לעומתMCP6023-I/SN)
- Supports compact low-voltage rail-to-rail signal paths (לעומתMCP6023T-E/SN)
- Provides integrated control for multi-amplifier systems (לעומתMCP6023T-I/SN)
הערות תכנון
Place the supply bypass capacitor directly between the positive supply and ground pins, with the ground connection following the shortest practical return path. For the 2.5 V minimum operating voltage, verify that supply tolerance, startup droop, and regulator ripple remain inside the manufacturer limits. Place input and feedback components close to the relevant pins, and avoid routing the high-impedance input node beneath or beside clocked and switching traces.
The 10 MHz gain-bandwidth product does not guarantee a usable closed-loop bandwidth of 10 MHz at every gain. Calculate the required gain from the closed-loop transfer function, then confirm stability with the intended source impedance, load, and feedback network. Simulate capacitor loading and output-current demand before attaching long cables, large capacitors, or high-level signals, particularly where the rail-to-rail output must remain within linear limits.
Do not leave either input floating, and confirm the required common-mode voltage for every operating condition. The chip-select function also needs a defined state during reset and power-up; otherwise, the output can affect the feedback network before the intended signal path is active. Review the exact 8-pin SOIC pin table in the manufacturer datasheet before changing the PCB or substituting a differently suffixed MCP6023 ordering code.
מידע על תאימות
Compliance status is not stated in the manufacturer page excerpt or distributor results and should be confirmed from the Microchip product documentation and material declarations.