Microchip Technology

MCP6023-E/SN - 10MHz RRIO Op Amp | Microchip

MPN: MCP6023-E/SN ✓ Active
<0.5 mV Vdss 1.0 mA Id 8-pin SOIC, 0.154 inch body width, 3.90 mm width Package
MOQ: 1 |

MCP6023-E/SN Overview

The Microchip Technology MCP6023-E/SN is a single operational amplifier with a 10 MHz gain-bandwidth product, 1.0 mA typical operating current, and input offset voltage below 0.5 mV, housed in an 8-pin SOIC package. It provides rail-to-rail input and output operation from a 2.5 V supply, combining low power consumption with useful high-speed performance.

An operational amplifier, or op amp, is a high-gain analog building block used in signal-conditioning and feedback systems. Its place in the hierarchy is signal amplifier -> operational amplifier -> analog integrated circuit -> semiconductor. Rather than increasing a signal's power level, an op amp compares its input voltages and drives its output to reduce error within a feedback network. Rail-to-rail input and output operation allows useful signal ranges to extend close to the supply rails.

The MCP6023-E/SN combines several characteristics suited to compact analog circuits. Its 10 MHz gain-bandwidth product supports higher-frequency closed-loop amplification than a low-bandwidth precision amplifier. Its 1.0 mA typical operating current supports portable and low-power designs. Input offset voltage below 0.5 mV helps reduce systematic error in DC-coupled amplifiers, while the rail-to-rail output supports direct drive of modest loads without requiring an output-swing margin as large as that of some conventional amplifiers.

Microchip describes the MCP6023 as a CMOS operational amplifier with low bias current, high open-loop gain, high-speed operation, and rail-to-rail output swing. The chip-select feature adds control useful in multichannel systems where several amplifiers share a supply. CMOS construction is appropriate for battery-operated equipment because it supports low static supply demand, although the complete circuit's energy use also depends on output swing, load, and operating frequency.

Typical uses include sensor-signal conditioning, low-level analog measurement, audio paths, active filtering, and general-purpose gain stages. Its rail-to-rail behavior is particularly useful when signals occupy a substantial portion of the available supply range. Designers should still evaluate closed-loop stability, output-current capability, capacitive-load driving, input common-mode behavior, and system noise rather than treating the 10 MHz gain-bandwidth figure as a direct single-pole operating rate.

For PCB implementation, place the bypass capacitor close to the supply pins and connect the input common-mode reference properly for single-supply operation. Avoid leaving unused inputs floating, and verify whether the chip-select state introduces an output condition that affects feedback-loop startup. Keep sensitive input traces short and away from fast-switching nodes to minimize coupled noise.

This product record combines the manufacturer's core operating characteristics, package identification, sourcing guidance, same-family drop-in options, and practical circuit-selection notes. It supports faster engineering decisions by separating the MCP6023-E/SN's verified attributes from application-specific assumptions and by highlighting the checks required during footprint-compatible replacement.

Drop-in alternatives for MCP6023-E/SN — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with MCP6023-E/SN (same form factor and footprint) — differing in Amplifier Type, Input Offset Voltage, Package.

Microchip Technology
Amplifier Type: Single-circuit general-purpose operational amplifier
Input Offset Voltage: Less than 0.5 mV typical
Package: 8-pin SOIC
Microchip Technology
Amplifier Type: Single general-purpose operational amplifier
Input Offset Voltage: Less than 0.5 mV
Package: 8-pin SOIC

MCP6023-I/SN

✅ Drop-In
Microchip Technology
📦 8-pin SOIC
Single general-purpose operational amplifier · 1 circuit · 10 MHz · 1.0 mA · Less than 0.5 mV · 2.5 V · 5.5 V · Single

Contact for price

View Datasheet →

MCP6023T-E/SN

✅ Drop-In
📦 8-pin SOIC
Same 10 MHz amplifier family and 8-pin SOIC footprint; T ordering suffix changes the production packaging form

📋 Reference alternative (not in catalog)

MCP6023T-I/SN

✅ Drop-In
📦 8-pin SOIC
Same 10 MHz amplifier family and 8-pin SOIC footprint; T and I ordering suffixes differ from the target suffix

📋 Reference alternative (not in catalog)

MCP6023-E/SN Maximum Ratings & Electrical Characteristics

Amplifier Type Single operational amplifier
Gain-Bandwidth Product 10 MHz
Typical Operating Current 1.0 mA
Input Offset Voltage <0.5 mV
Minimum Supply Voltage 2.5 V
Output Swing Rail-to-rail
Input Type Rail-to-rail
Technology CMOS
Unity-Gain Bandwidth 10 MHz
Shutdown or Chip Select Chip select
Package 8-pin SOIC, 0.154 inch body width, 3.90 mm width
Mounting Type Surface mount

MCP6023-E/SN 8-pin soic, 0.154 inch body width, 3.90 mm width Pin Configuration Guide

Pin configuration for MCP6023-E/SN (8-pin soic, 0.154 inch body width, 3.90 mm width package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.

8-pin soic, 0.154 inch body width, 3.90 mm width package pinout diagram for MCP6023-E/SN

No detailed pinout data available for MCP6023-E/SN.

Refer to the datasheet for full pin configuration.

Typical Applications

MCP6023-E/SN is suitable for 6 applications: Low-Power Sensor Signal Conditioning, Portable Medical Monitoring, Industrial Sensor Acquisition, Audio Preamplifier Stage, Precision Active Filtering, Battery-Powered Data Acquisition.

🧩

Low-Power Sensor Signal Conditioning

MCP6023-E/SN fits low-power sensor front ends that require signal amplification close to the sensor rather than near the system ADC. Its 1.0 mA typical operating current minimizes amplifier contribution to a battery-powered design, while rail-to-rail input and output operation provides useful range in a low-voltage system. The 10 MHz gain-bandwidth product allows the amplifier to serve ordinary active filters and gain stages without relying on a high-bandwidth amplifier in the signal chain. Designers should still verify sensor impedance, input bias current, offset tolerance, noise, and the allowable capacitive loading before finalizing the gain and feedback network.

💊

Portable Medical Monitoring

The MCP6023-E/SN can condition low-level physiological or diagnostic sensor signals in portable monitoring equipment where both supply current and signal range matter. Its 1.0 mA typical operating current leaves more of the power budget for sensors, conversion, and radio transmission, while the rail-to-rail output supports signal chains operating near the available supply limits. The 10 MHz gain-bandwidth product is more than adequate for many slow physiological signals, but medical designs must separately assess offset, noise, leakage, isolation, and electrode-interface requirements. The amplifier must not be treated as a complete medical front end without those signal-chain checks.

🏭

Industrial Sensor Acquisition

MCP6023-E/SN is appropriate for buffering industrial sensor outputs when the signal chain requires rail-to-rail swing and a bandwidth above that of a basic precision op amp. The 10 MHz gain-bandwidth product supports general-purpose conditioning, filtering, and gain stages around slow or moderate-speed sensors, while 1.0 mA typical operating current simplifies power budgeting. Because industrial environments can introduce large transients and high-impedance sources, engineers should verify the exact input and output limits, common-mode behavior, noise, and stability. Protection, filtering, grounding, and isolation remain separate design functions and should not be inferred from the amplifier specifications alone.

🎧

Audio Preamplifier Stage

MCP6023-E/SN can serve as a general-purpose audio preamplifier or active-filter element in compact line-level and low-level audio circuits. Rail-to-rail output operation increases the usable signal range at low supply voltages, and the 10 MHz gain-bandwidth product gives adequate closed-loop bandwidth for typical audio-band stages. The 1.0 mA typical operating current also suits battery-powered audio equipment. Sound quality still depends on input-referred noise, distortion, output-current capability, load impedance, and layout, so those characteristics require separate verification. The amplifier should be configured with stable feedback and terminated source impedances rather than driving an unspecified reactive load.

📺

Precision Active Filtering

The MCP6023-E/SN is a practical choice for first-order and moderate-order active filters in compact analog systems. Its 10 MHz gain-bandwidth product provides bandwidth relative to filters operating in the audio, control, or low-frequency instrumentation range, and rail-to-rail output behavior helps preserve filter signals at low supply voltages. The typical operating current of 1.0 mA supports efficient multichannel designs. Filter component tolerances, amplifier finite-gain behavior, noise, and stability determine actual response accuracy, so simulation should include expected signal amplitude, load, and frequency rather than using gain-bandwidth product as a simple corner-frequency formula.

⚡

Battery-Powered Data Acquisition

MCP6023-E/SN fits battery-powered data-acquisition modules that combine a sensor, amplifier, and converter on a constrained power budget. The amplifier contributes 1.0 mA typical operating current, while rail-to-rail input and output operation reduces the need for an unnecessarily high supply voltage. Its 10 MHz gain-bandwidth product is suitable for buffering many sensors and implementing active anti-alias or signal-conditioning filters. The final design should calculate the complete signal-path power, verify converter input-range compatibility, and account for startup behavior of the chip-select function. This approach maximizes useful rail utilization without changing the required system measurement accuracy.

What are the key specifications of MCP6023-E/SN that engineers should know?
The MCP6023-E/SN is a single 10 MHz CMOS operational amplifier with rail-to-rail input and output operation, 1.0 mA typical operating current, and input offset voltage below 0.5 mV. According to the Microchip MCP6023 product page, it also provides high open-loop gain, low bias current, and a chip-select function. The device is packaged in an 8-pin SOIC with a 0.154-inch, 3.90 mm-wide body.
Where can I download the MCP6023-E/SN datasheet PDF?
The MCP6023-E/SN datasheet is available through Microchip Technology's MCP6023 product page at https://www.microchip.com/en-us/product/MCP6023. The manufacturer identifies the amplifier as a 10 MHz rail-to-rail input/output device with a 1.0 mA typical operating current. Use the manufacturer's PDF for the complete pin description, electrical limits, test conditions, and application guidance.
What is the supply voltage range of MCP6023-E/SN?
The MCP6023-E/SN operates from a minimum supply voltage of 2.5 V. The verified distributor description identifies this minimum rating, while the complete maximum rating and allowable supply combinations must be confirmed in the Microchip datasheet. This low-voltage capability makes the amplifier suitable for compact 2.5 V and higher single-supply systems when the signal and output ranges remain within the device's limits.
What does rail-to-rail input and output mean for MCP6023-E/SN?
Rail-to-rail operation allows the MCP6023-E/SN to accept input signals extending toward the supply rails and to produce an output swing toward those rails. Microchip identifies the MCP6023 as a rail-to-rail input/output amplifier with a 10 MHz gain-bandwidth product. This capability can reduce signal headroom requirements in low-voltage designs, although output-load and input-range details still determine the usable swing.
When should I choose MCP6023-E/SN instead of another single op amp?
Choose MCP6023-E/SN when a design needs one rail-to-rail CMOS amplifier with approximately 10 MHz gain-bandwidth product, 1.0 mA typical operating current, and offset voltage below 0.5 mV in an 8-pin SOIC. It is particularly suitable for low-power sensor conditioning and general analog signal processing. Select another amplifier when its wider accuracy, lower noise, output-current, or frequency requirements exceed this device's ratings.
Is MCP6023-E/SN suitable for sensor signal conditioning?
Yes, MCP6023-E/SN is suitable for many sensor-signal-conditioning stages because it offers rail-to-rail input and output operation, 1.0 mA typical operating current, and a 10 MHz gain-bandwidth product. These characteristics help preserve sensor signals in low-voltage systems and provide ample bandwidth for ordinary active filters and amplifiers. Sensor-specific accuracy depends on offset, bias current, noise, and error specifications evaluated against the measurement requirement.
Can MCP6023-I/SN replace MCP6023-E/SN?
MCP6023-I/SN is a same-family candidate that uses the same 8-pin SOIC format and has the same stated 10 MHz gain-bandwidth product, 1.0 mA typical operating current, and offset voltage below 0.5 mV. Before replacing MCP6023-E/SN, verify the exact temperature grade, chip-select behavior, ordering suffix, and all electrical limits in the manufacturer datasheet. The two temperature-grade suffixes should not be treated as interchangeable without that review.
What is the best drop-in replacement for MCP6023-E/SN?
The closest documented drop-in candidates are MCP6023-I/SN, MCP6023T-E/SN, and MCP6023T-I/SN because they belong to the MCP6023 family and retain the 8-pin SOIC format. Their temperature-grade and tape-versus-tube ordering codes require explicit review. A definitive replacement should preserve the required temperature range, chip-select logic, supply rating, and electrical limits, not merely the package outline.
What is the difference between MCP6023-E/SN and MCP6023T-E/SN?
MCP6023-E/SN and MCP6023T-E/SN are both MCP6023-family single amplifiers identified with 8-pin SOIC packaging and a 10 MHz gain-bandwidth product. Their ordering codes differ, so the manufacturer ordering table must be checked for temperature grade and shipping format before substitution. For a drop-in decision, confirm that the replacement preserves the operating-temperature range, chip-select function, and electrical limits of the original design.
MCP6023-E/SN versus MCP6023T-I/SN: which should I select?
Select MCP6023-E/SN when its specified grade matches the ambient-temperature requirements and the required production packaging form. MCP6023T-I/SN may be preferable only when its temperature grade, chip-select implementation, and ordering code meet the design. The cross-reference listings identify the same core 10 MHz amplifier family, but temperature qualification and packaging should decide the final selection.
Where can I buy MCP6023-E/SN and check its lead time?
Use the Request a Quote form on this page to request current MCP6023-E/SN pricing, stock confirmation, minimum order quantity, and lead time. The manufacturer product page identifies the device as an active 10 MHz operational amplifier. Commercial terms can change with inventory, volume, package form, and quality requirements, so obtain a current quotation for the exact MCP6023-E/SN ordering code.
What is the price of MCP6023-E/SN?
Current MCP6023-E/SN pricing should be obtained through the Request a Quote form on this page so that the commercial offer reflects the requested quantity, package form, and delivery requirements. The device is a catalog standard with a public Microchip product page. Request a written quotation for the exact suffix rather than relying on a generic family price or an unrelated package variant.
Is MCP6023-E/SN in stock and what is its lead time?
Current inventory and lead time for MCP6023-E/SN should be confirmed through the Request a Quote form on this page. The manufacturer lists the MCP6023 family as an active product, but device-level availability can vary with production packaging form and order quantity. Include the required quantity and destination in the request so the quotation can provide a meaningful schedule.
How should I find the MCP6023-E/SN pinout?
Use the pin-description table in the Microchip MCP6023 manufacturer datasheet before assigning PCB tracks or connecting the chip-select control. The device is identified as an 8-pin SOIC, but each signal name, no-connect designation, and pin number must be taken from the exact package drawing. The 8-pin package alone does not establish the functional mapping of every terminal.
What design checks matter for an MCP6023-E/SN amplifier circuit?
Check the 2.5 V minimum supply requirement, the rail-to-rail input/output range, the 10 MHz gain-bandwidth product, and the 1.0 mA typical operating current against the circuit. Also verify closed-loop stability, capacitive-load behavior, output-current demand, input bias current, and chip-select startup conditions. Place the supply bypass capacitor close to the amplifier and keep high-impedance input routes short.
What is a Microchip equivalent for MCP6023-E/SN from another manufacturer?
No cross-manufacturer drop-in equivalent is established by the cross-reference results for MCP6023-E/SN. A replacement from another manufacturer must independently match the 8-pin SOIC pinout, 2.5 V minimum supply, 10 MHz gain-bandwidth class, rail-to-rail behavior, chip-select function, and required temperature range. Use Microchip's cross-reference search for additional candidates, then verify every rating before committing to a production substitution.

Engineering reference data for MCP6023-E/SN — comparison, design guidance, and compliance information.

Selection Guide

Choose MCP6023-E/SN for a compact, low-power analog signal chain that needs one rail-to-rail CMOS amplifier, a 10 MHz gain-bandwidth product, 1.0 mA typical operating current, and an 8-pin SOIC footprint. MCP6023-I/SN is the closest same-family alternative when its temperature grade and ordering code fit the operating environment. MCP6023T-E/SN or MCP6023T-I/SN may be preferable when the required production-packaging form and temperature grade match the design. These same-family options share the core amplifier characteristics, so the deciding factors are ordering code, temperature qualification, packaging, lifecycle, and cost rather than basic bandwidth. Do not treat a shared SOIC outline as proof of equivalence: verify the complete pin map, chip-select logic, electrical limits, and stability. A cross-manufacturer alternative should be selected only after its 2.5 V supply capability, rail-to-rail behavior, gain-bandwidth product, offset, bias current, and chip-select function have all been checked against the original circuit.

Comparison with Alternatives

Parameter This Product MCP6023-I/SN MCP6023T-E/SN MCP6023T-I/SN
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 8-pin SOIC 8-pin SOIC - same 8-pin SOIC - same 8-pin SOIC - same
Amplifier Type Single operational amplifier Single operational amplifier Single operational amplifier Single operational amplifier
Gain-Bandwidth Product 10 MHz 10 MHz 10 MHz 10 MHz
Typical Operating Current 1.0 mA 1.0 mA 1.0 mA 1.0 mA
Input Offset Voltage <0.5 mV <0.5 mV <0.5 mV <0.5 mV
Minimum Supply Voltage 2.5 V 2.5 V 2.5 V 2.5 V
Input and Output Operation Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail
Technology CMOS CMOS CMOS CMOS
Ordering-Code Difference MCP6023-E/SN I temperature-grade suffix T production-packaging suffix T production-packaging and I temperature-grade suffixes

Key Differentiators

  • Combines low supply current with useful signal bandwidth (vs MCP6023-I/SN)
  • Supports compact low-voltage rail-to-rail signal paths (vs MCP6023T-E/SN)
  • Provides integrated control for multi-amplifier systems (vs MCP6023T-I/SN)

Design Notes

Place the supply bypass capacitor directly between the positive supply and ground pins, with the ground connection following the shortest practical return path. For the 2.5 V minimum operating voltage, verify that supply tolerance, startup droop, and regulator ripple remain inside the manufacturer limits. Place input and feedback components close to the relevant pins, and avoid routing the high-impedance input node beneath or beside clocked and switching traces.

The 10 MHz gain-bandwidth product does not guarantee a usable closed-loop bandwidth of 10 MHz at every gain. Calculate the required gain from the closed-loop transfer function, then confirm stability with the intended source impedance, load, and feedback network. Simulate capacitor loading and output-current demand before attaching long cables, large capacitors, or high-level signals, particularly where the rail-to-rail output must remain within linear limits.

Do not leave either input floating, and confirm the required common-mode voltage for every operating condition. The chip-select function also needs a defined state during reset and power-up; otherwise, the output can affect the feedback network before the intended signal path is active. Review the exact 8-pin SOIC pin table in the manufacturer datasheet before changing the PCB or substituting a differently suffixed MCP6023 ordering code.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

Compliance status is not stated in the manufacturer page excerpt or distributor results and should be confirmed from the Microchip product documentation and material declarations.

Data verified on: 2026-11-20 — data verified and curated by XAIPART's component engineering team

Related Searches

mcp6023 datasheet MCP6023-E/SN datasheet MCP6023-E/SN datasheet pdf MCP6023-E/SN pinout MCP6023-E/SN equivalent MCP6023-E/SN replacement MCP6023-E/SN vs MCP6023-I/SN Microchip MCP6023-E/SN MCP6023 10MHz rail-to-rail op amp MCP6023 2.5V 1mA amplifier MCP6023-E/SN SOIC-8 footprint MCP6023 sensor signal conditioning MCP6023-E/SN price MCP6023-E/SN stock MCP6023-E/SN cross reference

Related Components & Terms

Microchip Technology MCP6023-E/SN MCP6023-I/SN MCP6023T-E/SN MCP6023T-I/SN MCP6023 Operational amplifier Op amp Analog integrated circuit Semiconductor CMOS Rail-to-rail input Rail-to-rail output Gain-bandwidth product Input offset voltage Typical operating current Chip select 8-pin SOIC SOIC package family Surface-mount package Sensor signal conditioning Active filter Portable electronics 2.5 V minimum supply
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details