OPA341UA - 5.5MHz RRIO Op Amp with Shutdown | Texas Instruments
MPN: OPA341UA ✓ פעילOPA341UA סקירה
An operational amplifier, or op amp, is the active element in a feedback-control or signal-conditioning circuit that amplifies the voltage difference between its two inputs. The op-amp category belongs to the broader amplifier-IC and analog-signal-processing hierarchy. Rail-to-rail input and output operation extends the usable signal range beyond the traditional limits imposed by internal input and output saturation stages.
The OPA341UA combines a 5.5 MHz gain-bandwidth product with rail-to-rail input and output capability. A shutdown control allows the circuit designer to place the amplifier into a low-power state when signal processing is not required. Its single-amplifier configuration and SOIC-8 package also make it convenient for compact analog boards requiring a general-purpose precision amplifier rather than a multi-channel device.
The 5.5 MHz gain-bandwidth product is particularly useful for moderate-bandwidth signal conditioning, sensor interfaces, active filters, and low-level audio paths. Rail-to-rail inputs improve signal capture when operating from a 5 V rail, while rail-to-rail outputs help preserve dynamic range. The shutdown function adds system-level control that can be useful in portable instruments, sampling systems, and applications that alternate between active measurement and low-power states.
Typical applications include current-to-voltage conversion following a DAC, audio signal conditioning, portable measurement equipment, battery-powered sensing, and general-purpose analog filtering. In these systems, the amplifier can operate from a low-voltage supply while accepting input signals near either supply rail and providing output swing close to the available supply range.
The shutdown behavior, input/output common-mode limits, output-load capability, and stability conditions must be checked against the manufacturer datasheet for the intended supply voltage and signal frequency. Decoupling capacitors should be placed close to the supply pins, and the feedback network should preserve the required noise gain and phase margin at the selected operating frequency.
This product page combines the manufacturer's device information with package details, application guidance, compatibility analysis, and practical design considerations. It helps engineers identify whether the OPA341UA matches a low-voltage, rail-to-rail signal-chain requirement before completing a production design.
חלופות תחליף ישיר עבור OPA341UA — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם OPA341UA (אותו גורם צורה וטביעת רגל) — שונים ב Package.
OPA341UA/2K5
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
OPA340UA
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←OPA337UA
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
OPA341UA דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 5.5 MHz |
| Input Common-Mode Range | Rail-to-rail input |
| סוג פלט | Rail-to-rail output |
| Shutdown Support | Yes |
| Amplifier Class | Standard general-purpose amplifier |
| מארז | 8-pin SOIC |
| סוג הרכבה | Surface mount |
| טווח טמפרטורת פעולה | Extended temperature range; limits not stated in the product-page summary |
| סטטוס RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
תצורת פינים של OPA341UA
| פין 1 | OUT — Amplifier output |
| פין 2 | IN- — Inverting input |
| פין 3 | IN+ — Non-inverting input |
| פין 4 | V- — Negative supply connection |
| פין 5 | SHUTDOWN — Active shutdown control |
| פין 6 | V+ — Positive supply connection |
| פין 7 | NC — Not connected |
| פין 8 | NC — Not connected |
יישומים טיפוסיים
OPA341UA מתאים עבור 6 יישוםs: Portable Sensor Signal Conditioning, Battery-Powered Measurement Equipment, Audio Preamplifier Stage, DAC Current-to-Voltage Conversion, Active Analog Filter, Industrial Control Signal Interface.
Portable Sensor Signal Conditioning
The OPA341UA fits low-voltage sensor-conditioning stages that require rail-to-rail input acceptance and controlled shutdown. Its rail-to-rail input characteristic allows the amplifier to operate close to the limits of a 5 V-class supply, while the 5.5 MHz gain-bandwidth product provides useful bandwidth for moderate-speed sensor signals. Place the device in an active filter or non-inverting gain stage, and drive its shutdown control when the sensor is sampled infrequently to reduce system power. The design must preserve stable feedback and confirm the required common-mode and output headroom for the selected supply voltage.
מומלץ
Battery-Powered Measurement Equipment
OPA341UA is appropriate for battery-powered instruments that periodically enable an analog measurement chain. The shutdown function supports low-power operation, while the single amplifier and 8-pin SOIC package simplify board allocation compared with a multi-channel device. Its 5.5 MHz gain-bandwidth product is suitable for signal-conditioning stages beyond static sensor readings, including filtered measurements and small-signal amplification. Tie the shutdown control to the instrument's power-management logic and check the manufacturer datasheet for logic levels, start-up behavior, supply limits, and output settling before defining the measurement interval.
מומלץ
Audio Preamplifier Stage
The OPA341UA can be used in a low-voltage audio preamplifier when its rail-to-rail input and output operation match the signal range. The 5.5 MHz gain-bandwidth product supports audio-band amplification with additional headroom above the baseband region, and the amplifier can be disabled through shutdown when the audio path is inactive. Use conventional non-inverting or inverting feedback according to the required gain and bandwidth, and observe the output-swing and load limitations at the chosen supply voltage. The manufacturer datasheet should also be reviewed for noise, distortion, and stability at the selected closed-loop gain.
מומלץ
DAC Current-to-Voltage Conversion
The OPA341UA is specifically suited to current-to-voltage conversion at the output of a DAC. Rail-to-rail input behavior helps accommodate the voltage generated by the feedback resistor when the DAC output approaches a supply rail, and the 5.5 MHz gain-bandwidth product allows the transimpedance stage to operate beyond slow-resolution audio rates. Configure the feedback resistor and optional compensation capacitor from the manufacturer datasheet, then verify settling against the DAC output step and required accuracy. The shutdown input provides a way to isolate the output when the converter is not being used.
מומלץ
Active Analog Filter
OPA341UA can implement low-voltage active filters where rail-to-rail signal handling and a 5.5 MHz gain-bandwidth product are useful. The device is appropriate for first or second-order sections in a filter chain, particularly when signals span much of the low-voltage supply range. Select resistor and capacitor values for the intended pole or center frequency, then confirm loop gain and phase margin from the manufacturer datasheet at the selected noise gain. The shutdown function may be useful in switched-filter systems, but it should be sequenced so that the analog output does not produce an unwanted transient during state changes.
מומלץ
Industrial Control Signal Interface
OPA341UA is suitable for general-purpose industrial control interfaces operating from low-voltage supplies. Rail-to-rail inputs help process control signals near the supply range, and the 5.5 MHz bandwidth supports faster diagnostics and conditioning than a strictly low-frequency amplifier. The amplifier can condition sensor outputs, error-amplifier signals, or buffered control references. Provide local supply bypassing, maintain an appropriate feedback network, and verify input protection because rail-to-rail operation alone does not make the device tolerant of external overvoltage. Use the shutdown function when the controlled subsystem can be placed in a defined inactive state.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור OPA341UA — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | OPA341UA/2K5 | OPA340UA | OPA337UA |
|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Amplifiers | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 5.5 MHz | 5.5 MHz | 5.5 MHz | 5.5 MHz |
| Maximum Supply Voltage | 5.5 V | 5.5 V | 5.5 V | 5.5 V |
| Input Common-Mode Range | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input |
| Output Type | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
מבדילים עיקריים
- Integrated shutdown control within a general-purpose rail-to-rail amplifier (לעומתOPA340UA)
- Same 5.5 MHz performance class in a common SOIC-8 footprint (לעומתOPA337UA)
- Identical electrical configuration with a production reel order option (לעומתOPA341UA/2K5)
הערות תכנון
Place the input, output, and supply connections so that feedback traces remain short and minimize parasitic capacitance around high-impedance nodes. Connect the bypass capacitor directly between the V+ and V− pins, with its ground return terminating close to the device. Keep the SOIC-8 footprint free of unintended copper beneath sensitive input routes if the application uses high source impedance.
Design the shutdown control so it cannot float during reset or brownout conditions. Pull the shutdown pin to the state required for normal operation, account for its logic levels and current in the control circuit, and avoid driving the pin through a long trace that could pick up noise. Sequencing is especially important when the amplifier shares a supply rail with a DAC or precision sensor.
Select the feedback resistors and gain according to the 5.5 MHz gain-bandwidth product and the required closed-loop bandwidth. At low noise gains, verify capacitive-load stability using the manufacturer guidance rather than adding large capacitors directly at the output. For current-to-voltage conversion, keep the feedback resistor close to the inverting input and use the datasheet's recommended compensation arrangement when driving practical load capacitances.
Do not assume rail-to-rail input means unlimited input range or that the output can reach either supply rail under every load. Check input common-mode limits, output headroom, and maximum supply voltage for the selected operating point. Also avoid treating the OPA341UA as a direct substitute for a non-shutdown amplifier without reviewing pin 5 and confirming how the original board drives that node.
מידע על תאימות
The manufacturer product information confirms an extended-temperature industrial amplifier but does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.