OPA691ID - 280MHz Wideband Op Amp | Texas Instruments
MPN: OPA691ID ✓ פעילOPA691ID סקירה
A current-feedback operational amplifier is a voltage-feedback amplifier architecture optimized for high-speed applications. Unlike a conventional voltage-feedback amplifier, the OPA691 uses feedback-node impedance to establish gain, which supports wide bandwidth and high slew rate while operating from a low 5.1 mA supply current. The resulting hierarchy places it among high-speed operational amplifiers, analog signal-chain ICs, amplifiers, and semiconductor devices.
The principal performance characteristics include a 190 mA output current rating, ±4.0 V output voltage swing, 2,100 V/µs slew rate, and 2 GHz gain-bandwidth product. Unity-gain stability allows the amplifier to be used directly at a gain of one. The disable input adds a practical control function: leaving it open or holding it high permits normal operation, while pulling it low reduces supply current to less than 150 µA and places the output in a high-impedance state.
The OPA691ID is specified for an ambient operating-temperature range of −40°C to +85°C and uses the TI D-package 8-pin SOIC configuration. Its low supply current combines with wide bandwidth and high output-current capability, making it useful where signal fidelity, large-swing drive, and controlled power-down behavior are all important. Designers should also account for the datasheet limits on output swing, supply voltage, disable-pin logic, input common-mode range, and external feedback components.
Typical uses include video and broadcast signal conditioning, communications infrastructure, test and measurement front ends, active filters, and high-speed instrumentation. The part is especially relevant where a wideband amplifier must operate from a compact 8-pin SOIC footprint and provide low-current shutdown behavior. In systems using polarity reversal or supply-level shifting, the ±6 V dual-supply capability can simplify signal-chain implementation.
Use the manufacturer datasheet pin-description table when assigning PCB tracks, especially because the disable function and supply rails determine safe routing and logic-level compatibility. Place input, output, supply-decoupling, and feedback components close to the device to minimize parasitic capacitance. Validate stability, bandwidth, output swing, and disable timing in the final board layout rather than relying only on ideal-device calculations.
This page combines the manufacturer product information, ordering details, functional characteristics, package data, and cross-reference findings into an engineering-focused product record. It also identifies the limits of drop-in substitution: no distinct non-packaging drop-in alternatives were confirmed for the OPA691ID, so variant names should not be treated as equivalent devices without electrical and pin-level verification.
חלופות תחליף ישיר עבור OPA691ID — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
OPA691IDR
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
OPA691IDG4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
OPA691IDRG4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
OPA691ID דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Current-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 2 GHz |
| Current Feedback Bandwidth | 280 MHz |
| Slew Rate | 2,100 V/µs |
| Output Current | 190 mA |
| Output Voltage Swing | ±4.0 V |
| זרם אספקה | 5.1 mA |
| Maximum Single-Supply Voltage | +12 V |
| Maximum Dual-Supply Voltage | ±6 V |
| Unity-Gain Stable | Yes |
| Disable-State Supply Current | Less than 150 µA |
| Disable Output State | High impedance |
| טמפרטורת פעולה | −40°C to +85°C |
| מארז | 8-pin SOIC (D package) |
| סוג הרכבה | Surface mount |
מדריך תצורת פינים של OPA691ID 8-pin soic (d package)
תצורת פינים עבור OPA691ID (מארזת 8-pin soic (d package)). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור OPA691ID.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
OPA691ID מתאים עבור 6 יישוםs: Wideband Video Signal Conditioning, Communications RF and Baseband Front Ends, High-Speed Instrumentation Amplification, Active Wideband Filters, Data Acquisition and Test Systems, Low-Power Signal Multiplexing.
Wideband Video Signal Conditioning
The OPA691ID fits wideband video conditioning because its 280 MHz current-feedback bandwidth, 2 GHz gain-bandwidth product, and 2,100 V/µs slew rate preserve large-amplitude signals across a broad frequency range. Place it as a low-gain or fixed-gain stage between a source and an ADC, cable driver, or monitor input, with the feedback network selected according to the manufacturer datasheet. Its ±4.0 V output swing and 190 mA output capability help support downstream stages, while the disable input can provide controlled shutdown. Validate gain accuracy, output settling, and capacitive-load behavior on the final PCB.
מומלץ
Communications RF and Baseband Front Ends
The OPA691ID is applicable to communications front ends requiring high bandwidth and fast output transitions, including low-level IF and baseband conditioning stages. Its 190 mA output-current capability provides margin for moderate loading, while the 5.1 mA operating supply current limits power demand in distributed equipment. The amplifier accepts single- or dual-supply operation up to +12 V or ±6 V, allowing the signal path to match different rail plans. Feedback resistors, input biasing, and disable logic require careful review because current-feedback gain and common-mode limits differ from conventional voltage-feedback designs.
מומלץ
High-Speed Instrumentation Amplification
The OPA691ID supports fast instrumentation stages where sensor or test-signal bandwidth would be degraded by a slower general-purpose amplifier. Its 280 MHz current-feedback bandwidth and 2,100 V/µs slew rate allow rapid signal transitions, and the unity-gain-stable architecture provides flexibility around a one-volt-per-volt stage. Use the device with carefully placed feedback components and controlled source impedance to maintain predictable behavior. The 190 mA output current can help drive moderate scope or analyzer inputs, but cable loading, probe capacitance, and oscilloscope input topology must be included in system validation.
מומלץ
Active Wideband Filters
OPA691ID is well suited to wideband active filtering because its unity-gain stability, 2,100 V/µs slew rate, and 280 MHz current-feedback bandwidth allow small-signal operation beyond the bandwidth of many general-purpose amplifiers. The 190 mA output-current rating helps drive the reactive input and output networks encountered in active filters. Component tolerance, amplifier input impedance, and parasitic capacitance will set practical filter response and peaking, so calculations should be repeated with realistic parts and the assembled board. The disable pin can also isolate the stage during power-down or measurement sequences.
מומלץ
Data Acquisition and Test Systems
The OPA691ID can serve as a high-speed buffer or gain stage in data-acquisition equipment where acquisition-system input bandwidth is a limiting factor. Its 2 GHz gain-bandwidth product and 2,100 V/µs slew rate reduce the risk of slew-limited acquisition, while 190 mA output current provides useful drive capability. Place the amplifier close to the acquisition front end to minimize trace capacitance and reflections, and verify that the selected feedback network remains stable with the converter or instrument input. The shutdown function supports controlled operating states in multichannel systems.
מומלץ
Low-Power Signal Multiplexing
The OPA691ID is useful in multiplexed signal paths because pulling the disable pin low reduces supply current to less than 150 µA and places the output in a high-impedance state. In normal operation, the amplifier delivers 280 MHz current-feedback bandwidth and 2,100 V/µs slew rate, allowing disabled channels to be re-enabled without changing the basic footprint of the active channel. The multiplexing architecture must account for input and output loading, isolation behavior, switching transients, and logic levels. Leaving the disable pin open provides normal operation according to the manufacturer product information.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור OPA691ID — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Package | 8-pin SOIC (D package) |
| Brand | Texas Instruments |
| Amplifier Architecture | Current feedback |
| Current Feedback Bandwidth | 280 MHz |
| Gain-Bandwidth Product | 2 GHz |
| Slew Rate | 2,100 V/µs |
| Output Current | 190 mA |
| Operating Supply Current | 5.1 mA |
| Maximum Single-Supply Voltage | +12 V |
| Maximum Dual-Supply Voltage | ±6 V |
| Disable-State Supply Current | Less than 150 µA |
| Operating Temperature | −40°C to +85°C |
מבדילים עיקריים
- Combines wideband current-feedback performance with a low-power shutdown function (לעומתOPA691IDR)
- Provides high output-current capability for a compact 8-pin SOIC amplifier (לעומתOPA691IDG4)
- Supports flexible single- and dual-supply operation (לעומתOPA691IDR)
הערות תכנון
Keep the OPA691ID input, output, feedback, and supply connections short, and place the manufacturer-recommended bypass capacitors directly across the relevant supply pins. High-speed op amps can form unintended feedback paths through ground and supply impedance, so use a continuous ground reference and avoid routing the feedback network beside noisy or high-current traces. Validate settling time and stability with the final enclosure, cables, and load because parasitic inductance and capacitance can materially affect a 2 GHz gain-bandwidth-product device.
Use the datasheet feedback-resistor recommendations because OPA691ID is a current-feedback amplifier whose gain depends on feedback impedance. Place feedback components close to the device, keep the summing node compact, and minimize capacitance on the inverting input. Check the output against the expected capacitive load and destination input capacitance; excessive loading can produce peaking, ringing, or reduced bandwidth even when the amplifier is unity-gain stable.
The normal operating supply current is 5.1 mA, while the disable state reduces it to less than 150 µA. When assigning the disable signal, account for the manufacturer's stated behavior: open or high enables normal operation, while low commands the high-impedance output state. Confirm logic thresholds, supply sequencing, and any pull resistor arrangement so the pin remains in a defined state during reset. Verify the analog output for transient behavior when the channel is enabled or disabled.
Do not interpret the ±6 V dual-supply or +12 V single-supply capability as a guarantee of full rail-to-rail operation. The output swing is specified as ±4.0 V, and usable input range also depends on the supply arrangement. Check headroom, output-current limits, and thermal conditions against the actual load. The 190 mA current rating is a key capability but does not remove the need to verify continuous operation, package dissipation, and temperature rise.
מידע על תאימות
The accessible manufacturer and distributor excerpts do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for OPA691ID. AEC-Q100 qualification is not indicated and is not applicable to this catalog entry.