OPA890ID - 130MHz, 500V/us Single Op Amp | Texas Instruments
MPN: OPA890ID ✓ פעילOPA890ID סקירה
A voltage-feedback operational amplifier is an analog signal-conditioning amplifier that uses negative feedback to control gain and bandwidth. The OPA890ID belongs to the operational-amplifier hierarchy and is suitable for precision analog, communications, instrumentation, and signal-processing systems requiring much greater bandwidth than general-purpose amplifiers.
Key characteristics include a 130 MHz gain-bandwidth product, 500 V/us slew rate, single-amplifier configuration, and an operating supply range of ±1.5 V to ±6 V. The wide bandwidth enables closed-loop operation at high frequencies, while the high slew rate supports accurate reproduction of rapidly changing waveforms. The shutdown function allows the amplifier to be disabled when a circuit does not require continuous operation.
The OPA890ID uses a voltage-feedback architecture, which provides a direct relationship between input differential voltage and output voltage through the external feedback network. Its bandwidth and slew-rate characteristics make it appropriate for low-amplitude, high-speed signal paths rather than slow precision-only applications. Designers must account for gain-bandwidth interaction, output-voltage swing, input common-mode range, stability, and the effect of parasitic capacitance at high frequencies.
Typical uses include video and communications signal conditioning, waveform generation, data-conversion interfaces, active filters, and low-level instrumentation. The disable pin can support power management or isolate an amplifier during selected operating modes. In dual-supply systems, the ±1.5 V to ±6 V capability permits operation from low-rail analog and mixed-signal supplies.
PCB implementation should minimize trace length around the feedback network, maintain symmetrical routing, provide a solid ground reference, and place decoupling capacitors close to the supply pins. Feedback-component values should be checked against the selected closed-loop gain and the device's stability requirements. This page combines ordering information, verified electrical details, comparison guidance, and practical high-frequency layout considerations.
חלופות תחליף ישיר עבור OPA890ID — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
OPA890IDG4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
OPA890UA
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
OPA890ID דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Voltage-feedback operational amplifier |
| Number of Amplifiers | 1 amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 130 MHz |
| Slew Rate | 500 V/us |
| Minimum Supply Voltage | ±1.5 V |
| Maximum Supply Voltage | ±6 V |
| Shutdown Control | Yes |
| מארז | 8-pin SOIC |
| סוג הרכבה | Surface mount |
| טופולוגיה | Single amplifier |
מדריך תצורת פינים של OPA890ID 8-pin soic
תצורת פינים עבור OPA890ID (מארזת 8-pin soic). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור OPA890ID.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
OPA890ID מתאים עבור 6 יישוםs: Wideband Communications Signal Conditioning, Data-Conversion Interface, Active Wideband Filtering, Video and Imaging Signal Chains, Precision Instrumentation Front End, Waveform Generation and Buffering.
Wideband Communications Signal Conditioning
The OPA890ID fits communications front ends that require low-amplitude signals to be amplified without severe bandwidth limitations. Its 130 MHz gain-bandwidth product and 500 V/us slew rate support closed-loop gains and frequencies that are generally unsuitable for conventional low-speed amplifiers. Place the amplifier close to the source and feedback network to limit parasitic feedback. The principal trade-off is that high-speed layouts are more sensitive to board capacitance, grounding, and component tolerances than low-frequency precision stages.
מומלץ
Data-Conversion Interface
OPA890ID can serve as the gain or driver stage between a data converter and an external analog network. A 130 MHz gain-bandwidth product offers useful bandwidth margin, while the 500 V/us slew rate helps preserve the edge rate of high-speed signals. The circuit must be designed around the converter's settling requirements and the amplifier's input common-mode and output-swing limits. Keep routing short and maintain a continuous return path between the converter, amplifier, and decoupling network.
מומלץ
Active Wideband Filtering
The OPA890ID is appropriate for active filters whose useful passband extends beyond the range of general-purpose operational amplifiers. Its 130 MHz gain-bandwidth product supports higher closed-loop bandwidth, and the 500 V/us slew rate reduces slew-related distortion in large-signal transitions. Component tolerances and parasitic capacitance become increasingly important as filter order and bandwidth rise. Use the manufacturer's recommended feedback values and verify stability with the final source and load impedances.
מומלץ
Video and Imaging Signal Chains
OPA890ID can be used in low-amplitude video or imaging paths that require high bandwidth and fast edge response. The 130 MHz gain-bandwidth product is suitable for wideband amplification stages, while the 500 V/us slew rate can improve reproduction of rapid transitions. Video designs must also check output swing, gain linearity, and channel-to-channel matching against the source and load. Short traces and solid ground planes are essential at these signal speeds.
מומלץ
Precision Instrumentation Front End
The OPA890ID can amplify low-level instrumentation signals when the required bandwidth warrants a wideband amplifier. Its 130 MHz gain-bandwidth product and 500 V/us slew rate support faster measurement and control loops than general-purpose amplifiers, although offset, bias current, and noise specifications must be checked against the required accuracy. Use guarded input routing, careful grounding, and an appropriate low-noise supply. The shutdown function can reduce system activity when a measurement channel is not required.
מומלץ
Waveform Generation and Buffering
OPA890ID is useful in waveform-generation, buffer, and driver circuits where fast transitions and high loop gain are important. Its 500 V/us slew rate supports rapid output movement, and the 130 MHz gain-bandwidth product gives designers frequency headroom when configuring closed-loop gain. Load capacitance and output-current limits determine whether an additional output stage is needed. Validate output compliance and thermal behavior with the intended load, and keep the feedback network away from high-current switching paths.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור OPA890ID — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | OPA890IDG4 | OPA890UA |
|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Type | Voltage-feedback operational amplifier | Voltage-feedback operational amplifier | Voltage-feedback operational amplifier |
| Number of Amplifiers | 1 amplifier | 1 amplifier | 1 amplifier |
| Gain-Bandwidth Product | 130 MHz | 130 MHz | 130 MHz |
| Slew Rate | 500 V/us | 500 V/us | 500 V/us |
| Supply Voltage Range | ±1.5 V to ±6 V | ±1.5 V to ±6 V | ±1.5 V to ±6 V |
| Disable Function | Yes | Yes | Yes |
| Mounting Type | Surface mount | Surface mount | Surface mount |
מבדילים עיקריים
- Wideband performance in an 8-pin SOIC amplifier (לעומתOPA890IDG4)
- Single-amplifier package preserves board area (לעומתOPA890UA)
- Dedicated shutdown control supports system power management (לעומתOPA890IDG4)
הערות תכנון
Keep the OPA890ID feedback loop compact and route both feedback legs directly from the output and inverting-input pins to their network components. At 130 MHz bandwidth and 500 V/us slew rate, board capacitance can alter closed-loop gain and phase margin. Avoid routing the sensitive input node beneath the device, keep the output trace away from the input, and use a continuous ground plane beneath the amplifier.
Place the supply bypass capacitor as close as practical to the OPA890ID supply pins and connect it to the same ground reference used by the signal path. Keep the capacitor connection short because trace inductance becomes significant when the amplifier transitions quickly. For dual-supply operation, provide bypass paths for both rails and verify the disable-pin state during power-up to avoid an unintended transient at the output.
Do not select the OPA890 solely by its 130 MHz gain-bandwidth product. Verify closed-loop gain, source and load impedance, output swing, input common-mode range, supply current, noise, and shutdown behavior for the actual operating point. A wideband amplifier that is lightly loaded or driven by excessive capacitance can behave differently from the ideal gain-bandwidth and slew-rate headline figures.
מידע על תאימות
The exact OPA890ID environmental and qualification declarations are not stated in the verified part listings. Consult the Texas Instruments product page and manufacturer datasheet before making a compliance declaration.