PCA9671D - 16-Bit I2C FM+ I/O Expander | NXP
MPN: PCA9671D ✓ AktifPCA9671D Ringkasan
An I/O expander is an interface IC that extends the number of controllable input or output lines available from a host processor. The PCA9671D belongs to the I/O expander hierarchy within interface ICs and semiconductor devices. Its Fast-mode Plus capability allows a higher bus rate than conventional 400 kHz I2C operation, making it suitable for systems that need flexible logic-control functions without dedicating numerous host-controller pins.
The main features include 16 output ports, 1 MHz I2C operation, a reset input, and configurable pull-up behavior represented by the PU designation. The reset function provides a defined way to restore the device state during system initialization or fault recovery. Each output can serve as a general-purpose logic signal, while bus-driven functions can extend the device beyond simple static GPIO control.
The PCA9671D is designed for use with microcontrollers and other embedded processors that lack sufficient direct I/O pins. Its 24-pin SO package supports compact PCB layouts while keeping the I2C connection simple. Because an I/O expander adds bus-controlled peripheral functions around the processor, designers should account for bus timing, address allocation, pull-up resistors, output load limits, and reset timing in the system architecture.
Typical uses include LED status and indicator arrays, relay-control interfaces, reset or enable signaling for external circuits, industrial control modules, communication equipment, and embedded systems with several discrete logic outputs. The 1 MHz bus rate can reduce communication delay when many outputs are updated, while the 16-bit output count consolidates control traffic into a compact serial interface.
Layout should place pull-up components and decoupling close to the relevant device pins, and the I2C routing should preserve signal integrity. Firmware must assign a unique address, configure the intended output states, and account for the reset state before enabling external loads. The manufacturer datasheet is the controlling reference for absolute maximum ratings, electrical limits, pin functions, and recommended operating conditions.
This product page consolidates the confirmed interface, package, and ordering information with practical design guidance for I2C layout, reset implementation, firmware configuration, and system expansion. It is intended to help engineers determine whether the PCA9671D can satisfy a remote-output requirement while avoiding unnecessary host-controller pin allocation.
Pilihan pengganti yang segera untuk PCA9671D — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Tiada pilihan pengganti yang segera untuk produk ini.
Minta AlternatifPCA9671D Spesifikasi
| Number of I/O Outputs | 16 outputs |
| I2C Maximum Clock Frequency | 1 MHz |
| Jenis Antaramuka | I2C Fast-mode Plus (Fm+) |
| Reset Function | Yes |
| Pull-Up Configuration | PU |
| Package Pin Count | 24 pins |
| Package Designation | 24-SO |
| Device Category | I/O expander |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin PCA9671D 24-so
Konfigurasi pin untuk PCA9671D (24-so pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk PCA9671D.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
PCA9671D patut untuk 6 aplikasis: LED Status and Indicator Arrays, Relay and Discrete Logic Control, Embedded System I/O Expansion, Communication Equipment Control, Power-Sequencing and Enable Control, Instrumentation and Test Control.
LED Status and Indicator Arrays
The PCA9671D fits LED status and indicator designs because it provides 16 outputs while operating on an I2C bus up to 1 MHz. A host microcontroller can update several visual indicators over the same two-wire bus instead of consuming one dedicated GPIO pin for every lamp. The reset function supports deterministic initialization of the display state after power-up. Because the manufacturer documentation associates PCA9671 capability with bus-driven LED functions, engineers should verify output-drive limits, polarity, and the required PWM configuration in the NXP datasheet. The principal benefit is PCB and firmware simplicity, while the trade-off is that each update consumes I2C bus time and all remote outputs share the host's bus reliability.
Disebarkan
Relay and Discrete Logic Control
The PCA9671D is suitable for relay-control and discrete-logic interfaces when the host controller has limited GPIO capacity. Sixteen output lines can represent relay commands, equipment enables, alarms, or interlock signals through suitable external interface circuitry, while the 1 MHz Fm+ bus supports comparatively quick command transfer. Reset provides a controlled recovery point during startup or system faults. Designers must confirm voltage levels, output current, isolation requirements, and whether an external driver stage is necessary before connecting a load. The PCA9671D reduces host-pin usage, but it does not replace high-current drivers, isolation, or protection required by the final relay and industrial interface circuit.
Disebarkan
Embedded System I/O Expansion
The PCA9671D is a practical choice when an embedded processor must support more digital control lines than its package provides. The 16-bit remote I/O structure allows a microcontroller or application processor to retain a compact pin count while adding status and control points elsewhere on a PCB. The I2C interface operates up to 1 MHz, and reset provides an initialization mechanism for the expanded outputs. The 24-SO package must be checked against the PCB footprint and assembly process. The design trade-off is bus dependency: firmware must configure addresses and output states, while the I2C network must maintain timing margins and reliable pull-ups for all connected devices.
Disebarkan
Communication Equipment Control
The PCA9671D fits communication equipment that requires several remote enables, status indicators, or module-control signals without dedicating a large number of host pins. Its 16 outputs and 1 MHz I2C operation allow control traffic to be consolidated on the processor's existing two-wire bus. Reset can be incorporated into the equipment's startup and recovery sequence. System planners should use the NXP timing information to validate bus capacitance, pull-up selection, and the number of competing I2C devices. The PCA9671D simplifies the processor interface, but address conflicts, bus faults, and software state management remain the designer's responsibility.
Disebarkan
Power-Sequencing and Enable Control
The PCA9671D can distribute enable, reset, or power-sequencing commands to multiple peripheral circuits when direct host-controller pins are limited. Sixteen outputs provide room for several controlled loads, while the reset input establishes a known initialization point for the expansion interface. The device's I2C command path supports compact routing and software-configurable output states. Timing analysis must show that all downstream circuits tolerate the reset and startup sequence, and the NXP datasheet must be consulted for output-mode and electrical-limit details. The benefit is centralized sequencing with fewer host pins; the trade-off is that firmware must coordinate the sequence and avoid enabling loads before the surrounding system is ready.
Disebarkan
Instrumentation and Test Control
The PCA9671D is well suited to instrumentation and test systems that need multiple remote control lines across a larger circuit board. The 16 outputs can operate front-panel indicators, range-select commands, fixture enables, or status lamps while the 1 MHz I2C bus keeps the controller connection compact. Reset supports repeatable initialization before a measurement sequence. Layout should preserve I2C signal integrity and provide local decoupling, while firmware should avoid unnecessary bus traffic during high-rate acquisition. The PCA9671D offers a practical alternative to expanding the controller package, although it introduces a software-controlled dependency that must be included in system-level fault analysis.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk PCA9671D — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini |
|---|---|
| Package | 24-SO, 24 pins |
| Brand | NXP Semiconductors |
| Number of I/O Outputs | 16 outputs |
| I2C Maximum Clock Frequency | 1 MHz |
| Interface Class | I2C Fast-mode Plus (Fm+) |
| Reset Function | Yes |
| Pull-Up Configuration | PU |
| Device Type | Remote 16-bit I/O expander |
Penyeberangsung Jelas
- Sixteen remote outputs in one controller interface (vsPCF8575)
- Higher I2C bus drive capability (vsPCF8575)
- Fast-mode Plus support for compact control (vsPCA9671PW)
Catatan Desain
Place the PCA9671D close to the loads it controls to keep output traces short, while routing the I2C SDA and SCL lines away from switching nodes and high-current return paths. The exact I2C pull-up component values must be calculated from bus capacitance, voltage, and the complete device population using the NXP timing guidance. Decoupling placement and values should follow the manufacturer datasheet.
Define the state of all 16 outputs immediately after power-up and after a reset assertion. Firmware and external hardware should agree on whether loads remain off until configuration is valid. Review the output-drive and absolute-maximum limits in the NXP datasheet before connecting loads, especially when the remote interface drives devices outside the PCA9671D's direct current capability.
Do not treat another PCA9671 package option as a drop-in substitute solely because the functional description is similar. The PCA9671D is identified as 24-SO, while PCA9671PW denotes a different package option; verify body size, lead pitch, land pattern, pin numbering, and exposed functionality. Also confirm that the proposed part preserves the required reset behavior, I2C addressing, output modes, and 1 MHz bus performance.
The 1 MHz I2C rate increases timing sensitivity compared with conventional 400 kHz operation. Check bus rise time, pull-up strength, capacitance, and the cumulative loading of every attached device. Avoid long stubs and unnecessary vias, and use continuous ground references beneath the bus routing. Validate the worst-case trace and component tolerances before enabling Fast-mode Plus operation.
Maklumat Kesediaan
No explicit environmental, automotive, halogen-free, or conflict-minerals status was confirmed in the available records. Apply the required qualification and purchasing criteria before production release.