PIC24F08KL201-E/SO 16-Bit 32MHz MCU | Microchip Technology
MPN: PIC24F08KL201-E/SO ✓ פעילPIC24F08KL201-E/SO סקירה
The PIC24F is a 16-bit microcontroller architecture that combines a compact instruction set with integrated peripherals commonly used in embedded control designs. The PIC24F08KL201 includes MSSP peripherals for I2C and SPI communication and CCP peripherals for capture, compare, and PWM functions. These peripherals reduce the need for external components and allow designers to implement sensor interfaces, communication links, motor-control functions, and timing tasks with a compact controller.
The device includes 8 KB of Flash memory organized as 2.75K x 24 bits, along with 512 x 8 bytes of RAM. Its 32 MHz maximum operating frequency and 16 MIPS performance provide useful processing headroom for basic control, protocol handling, and low-complexity signal processing. The 20-pin SOIC package supports conventional PCB assembly and is suitable for designs requiring a small, readily handled package rather than a fine-pitch land pattern.
Typical applications include low-cost industrial controllers, sensor nodes, battery-powered instruments, consumer appliances, small motor-control boards, and compact communication modules. The MSSP block supports serial connectivity to sensors and external devices, while the CCP block supports timing and PWM functions in motor, lighting, and control applications. The integrated XLP features are particularly useful when the controller spends substantial time idle or operates from limited energy sources.
When designing a PCB around the PIC24F08KL201-E/SO, follow the manufacturer pinout and recommended decoupling requirements exactly. Provide a stable supply and adequate bypass capacitance near the device, reserve programming and debug access, and confirm the operating limits for the selected supply voltage and temperature range. Review the manufacturer datasheet for the exact pin names, electrical characteristics, and peripheral configuration.
This product page organizes the key specifications, application guidance, comparison points, and practical design considerations for engineers evaluating the PIC24F08KL201-E/SO. It is intended to support rapid part selection while preserving the importance of validating pin compatibility, firmware support, and application requirements before a design is released for production.
חלופות תחליף ישיר עבור PIC24F08KL201-E/SO — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם PIC24F08KL201-E/SO (אותו גורם צורה וטביעת רגל) — שונים ב Core Architecture, Package.
אין חלופות תואמות Drop-in עבור מוצר זה.
בקשת חלופותPIC24F08KL201-E/SO דירוגים מרביים ומאפיינים חשמליים
| Microcontroller Type | 16-bit PIC24F microcontroller |
| Operating Frequency | 32 MHz |
| Performance | 16 MIPS |
| Program Memory | 8 KB Flash |
| Program Memory Organization | 2.75K x 24 bits |
| Data Memory | 512 x 8 bytes RAM |
| מתח אספקה | 3 V |
| Low-Power Technology | nanoWatt XLP |
| Serial Communication Peripherals | MSSP with I2C and SPI |
| Timer Peripherals | CCP capture, compare, and PWM |
| מארז | 20-pin SOIC |
| Package Type | SOP |
| סוג הרכבה | Surface Mount |
| מספר פינים | 20 pins |
| Core Architecture | PIC24F 16-bit core |
מדריך תצורת פינים של PIC24F08KL201-E/SO sop
תצורת פינים עבור PIC24F08KL201-E/SO (מארזת sop). מעגל משולב דיגיטלי זה כולל GPIO, ממשקי תקשורת (UART, SPI, I2C) ופיני מתח. יש לעיין בגיליון הנתונים של היצרן לפונקציות פינים חלופיות ולאפשרויות תצורה. חיוני לתכנון מערכות משובצות ולפריסת PCB.
אין נתוני פריסת פינים מפורטים עבור PIC24F08KL201-E/SO.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
PIC24F08KL201-E/SO מתאים עבור 6 יישוםs: Battery-Powered Sensor Node, I2C Environmental Sensor Interface, Compact SPI Data Acquisition, Small Fan and Pump Controller, Cost-Sensitive Consumer Appliance, Industrial Control and Communication Module.
Battery-Powered Sensor Node
The PIC24F08KL201-E/SO fits battery-powered sensor nodes because its nanoWatt XLP architecture supports low-power operating modes while the 16-bit core provides more control capability than a basic 8-bit MCU. The MSSP block can operate an I2C or SPI sensor bus, and the 8 KB Flash capacity can store application firmware and calibration data. Place the device in the duty cycle so the controller remains asleep between measurements, wakes to acquire data, and returns to a low-energy state. Confirm sensor standby current and average operating current against the system power budget.
מומלץ
I2C Environmental Sensor Interface
The integrated MSSP peripheral makes the PIC24F08KL201-E/SO suitable for environmental monitoring boards that combine temperature, humidity, pressure, or gas sensors over I2C. Its 32 MHz operating frequency allows the MCU to service sensor transactions, apply filtering, update a display, and maintain a communications schedule without a larger application processor. The 512-byte RAM is sufficient for short measurement buffers and protocol state. Follow the sensor and Microchip interface requirements for pull-ups, address selection, and timing, and verify the bus capacitance when several devices share the line.
מומלץ
Compact SPI Data Acquisition
For a compact SPI acquisition or control module, the PIC24F08KL201-E/SO combines a 16-bit core, 32 MHz clock, and MSSP serial peripheral in a 20-pin SOIC package. The firmware can clock out sensors or converters, buffer results in 512 bytes of RAM, and expose status through another communications channel. SPI support can reduce wiring compared with parallel data buses and supports full-duplex transfers when the selected sensor requires it. Validate voltage levels, maximum clock rate, chip-select behavior, and grounding before production release.
מומלץ
Small Fan and Pump Controller
The CCP capture, compare, and PWM capabilities of the PIC24F08KL201-E/SO suit small fan, pump, valve, or actuator controllers where variable timing is needed but a dedicated motor driver is unnecessary for the MCU stage. At up to 16 MIPS, the controller can execute duty-cycle updates, monitor feedback signals, and coordinate simple protection logic. Use an external transistor or motor-driver circuit for current switching, and isolate that power stage from sensitive timing signals. Validate stall current, switching losses, EMI, and thermal margin in the final load path.
מומלץ
Cost-Sensitive Consumer Appliance
The PIC24F08KL201-E/SO is appropriate for cost-sensitive consumer appliances that need local control, serial communication, and programmable timing in a small package. The 8 KB Flash store supports focused control firmware, while MSSP can connect a display, sensor, or configuration interface and CCP can control indicator or actuator timing. The 20-pin SOIC outline is easy to assemble using conventional surface-mount methods. Keep high-current relays, heaters, and motor winders on a separate protected power section, and use firmware debouncing and fault handling for user-facing controls.
מומלץ
Industrial Control and Communication Module
The PIC24F08KL201-E/SO can serve as the local controller in a small industrial module that translates sensor or actuator information over I2C or SPI. Its 16-bit architecture and 32 MHz clock provide adequate responsiveness for protocol handling, state-machine execution, and periodic control tasks, while XLP features support idle periods between commands. The SOIC package is practical for industrial equipment requiring a serviceable, conventional footprint. Use isolation, surge protection, and appropriate grounding when the module connects to long external wiring, and validate environmental requirements against the exact ordering variant.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור PIC24F08KL201-E/SO — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Package | 20-pin SOIC |
| Brand | Microchip Technology |
| Core Architecture | 16-bit PIC24F core |
| Maximum Operating Frequency | 32 MHz |
| Performance | 16 MIPS |
| Flash Program Memory | 8 KB, organized as 2.75K x 24 bits |
| Data Memory | 512 x 8 bytes RAM |
| Serial Peripherals | MSSP supporting I2C and SPI |
| Low-Power Feature | nanoWatt XLP |
הערות תכנון
Route the 20-pin SOIC footprint only after checking the manufacturer’s exact package drawing and pin table. Place input/output bypass capacitors close to their associated power pins, provide a clean ground reference, and avoid long traces between the MCU and serial-bus devices. Keep programming and debug access available on the board when the design will require field firmware updates.
The listed supply voltage is 3 V, so the power architecture must maintain the manufacturer’s operating limits across temperature, load, and startup transients. Decouple each supply connection locally and keep switching-converter nodes away from sensitive analog or communication traces. For battery operation, measure the complete duty cycle because the XLP advantage depends on firmware sleep duration, peripheral state, and the time the MCU remains awake.
Do not treat a controller with similar memory capacity as a drop-in replacement. Validate every pin assignment, alternate function, interrupt vector, peripheral behavior, and development-tool requirement. The PIC24F08KL201-E/SO uses a 20-pin SOIC outline, so SSOP and other package variants require PCB changes. Confirm the exact -E/SO temperature and qualification requirements before committing the design to production.
מידע על תאימות
Compliance status must be confirmed for the exact -E/SO ordering variant using the manufacturer product page and current material declarations.