SN74LS684N - 8-Bit Magnitude Comparator | Texas Instruments
MPN: SN74LS684N ✓ פעילSN74LS684N סקירה
A magnitude comparator is a logic IC that determines the relative ordering of two multibit numbers. It belongs to the comparator, digital logic, logic IC, and semiconductor hierarchies. Unlike a general-purpose processor or programmable controller, the SN74LS684N performs its comparison directly from wired logic inputs, so the result becomes available without firmware or instruction sequencing.
The SN74LS684N supports both binary and BCD comparison, and its active-low indication outputs are useful for driving downstream enable, reset, or selection logic. The device is listed in a 20-pin PDIP package with a 0 to 70 °C operating-temperature range. These characteristics make it appropriate for legacy-compatible equipment, industrial control systems, counters, timers, test fixtures, and interface designs that retain through-hole logic boards.
The LS series implementation uses Schottky-clamped TTL-compatible logic. Its structured outputs indicate the comparison result while external cascaded logic can extend comparison beyond the native 8-bit width. Design engineers should therefore treat the comparator outputs as active levels rather than passive status indicators, account for propagation delay when chaining stages, and use pull-up or pull-down components wherever the receiving circuit requires a defined inactive level.
Typical applications include sorting and classification control, digital test-equipment limit checking, address and threshold comparison, arithmetic-unit control, BCD instrument processing, and industrial sequence controllers. In these systems, the two operand buses feed the comparator, while its equality and greater-than outputs coordinate a counter, register, latch, or alarm without requiring continuous software polling.
A critical PCB consideration is the 20-pin PDIP footprint. Pin-1 orientation, notch direction, and adequate spacing around the package must match the board pattern, especially when repairing legacy equipment. Keep the input and output traces short enough to limit propagation-delay uncertainty, and account for the operating-temperature limits when using the part outside controlled room-temperature environments.
This product page consolidates the device identity, package information, operating range, comparison functions, sourcing structure, replacement guidance, and practical logic-design considerations into an engineering-focused reference. It also highlights the limits of direct substitution by separating true pin-compatible options from related comparator functions that do not reproduce every output and feature of the SN74LS684N.
חלופות תחליף ישיר עבור SN74LS684N — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
SN74LS684NE4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
SN74LS684N דירוגים מרביים ומאפיינים חשמליים
| Comparator Type | 8-bit identity and magnitude comparator |
| Number of Data Bits | 8 bits |
| Supported Number Formats | Binary or BCD |
| Number of Compared Inputs | 2 groups of 8 bits |
| Equality Output | A=B, active-low output |
| Greater-Than Output | A>B, active-low output |
| Logic Family | LS-series TTL |
| סוג פלט | Active-low |
| טווח טמפרטורת פעולה | 0 °C to 70 °C |
| Package Type | PDIP-20 |
| Total Pin Count | 20 pins |
| סוג הרכבה | Through-hole |
מדריך תצורת פינים של SN74LS684N pdip-20
תצורת פינים עבור SN74LS684N (מארזת pdip-20). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור SN74LS684N.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
SN74LS684N מתאים עבור 6 יישוםs: Digital Counter Limit Detection, BCD Instrument Threshold Control, Sorting and Classification Control, Address and Threshold Decoding, Arithmetic Unit Control, Legacy Test and Measurement Equipment.
Digital Counter Limit Detection
The SN74LS684N fits counter-limit detection because it compares two complete 8-bit values in parallel and directly indicates equality or greater-than conditions. Connect the counter bus to one operand and the programmed threshold bus to the other; the active-low A=B output can qualify a selected count, while A>B can advance a sequencing stage. The 20-pin PDIP package preserves through-hole construction for legacy industrial and test equipment. Because comparison is performed in wired logic, the result does not depend on firmware polling or microcontroller instruction latency, although board-level propagation delay must be included when the counter changes rapidly.
מומלץ
BCD Instrument Threshold Control
The SN74LS684N is useful in BCD instrument systems that must compare an eight-digit decimal value with a stored threshold. Its binary or BCD comparison capability allows the two buses to be evaluated without software conversion, while the active-low A=B and A>B outputs can control an alarm, inhibit, or display-enable signal. This is advantageous in older measurement and panel-control equipment where a microcontroller would add unnecessary complexity. The design should preserve the documented logic levels and account for comparator delay, because BCD digits arriving from separate counters may not change simultaneously.
מומלץ
Sorting and Classification Control
The SN74LS684N supports sorting and classification hardware by evaluating whether an 8-bit item equals or exceeds a programmed boundary. Its equality output can initiate an accepted-item path, while the greater-than output can select a different bin or processing stage. This hard-wired approach is useful in high-throughput industrial test fixtures where a stream of encoded values must be routed according to a fixed limit. The dedicated comparator provides a deterministic hardware decision without repeated processor instructions, but the receiving registers should be clocked only after accounting for the device's propagation delay and any delays introduced by board traces.
מומלץ
Address and Threshold Decoding
The SN74LS684N can decode an 8-bit address or data value against a hardware threshold when the system requires more than simple equality decoding. The A=B output identifies an exact match, while A>B supports range-style decisions when combined with additional logic. This makes the device relevant to legacy bus monitors, register validators, and industrial controllers that classify an 8-bit field without a programmable lookup table. Its through-hole PDIP-20 package is particularly useful when repairing existing boards. Confirm the output states and timing in the manufacturer documentation, and do not substitute a comparator that omits one of the required result outputs.
מומלץ
Arithmetic Unit Control
The SN74LS684N can provide magnitude and equality information to an arithmetic-control section in legacy digital logic. Feeding two 8-bit operands into the comparator allows a controller to determine whether an accumulator has reached a target or exceeded a limit, then use those outputs to enable a counter, latch, or carry-related function. Unlike a software comparison, the hardware result is continuously available and can participate in a combinational control path. The 0 °C to 70 °C range suits controlled commercial environments, while the 20-pin PDIP footprint supports through-hole repair and retrofit work on older arithmetic boards.
מומלץ
Legacy Test and Measurement Equipment
The SN74LS684N fits legacy test and measurement equipment that compares an 8-bit DUT response with a binary or BCD limit. The A=B output can indicate a passing measurement, and A>B can trigger an over-limit alarm or inhibit a subsequent test step. This dedicated hardware comparison reduces the control burden of simple fixtures and remains practical for boards designed around LS-series TTL logic. Because the PDIP-20 package uses through-hole leads, inspect existing sockets for oxidation, clean contacts, and confirm pin-1 orientation. For replacement work, verify supply voltage and timing characteristics against the original system requirements.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור SN74LS684N — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | SN74LS684NE4 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | PDIP-20 | PDIP-20 |
| Comparator Type | 8-bit identity and magnitude comparator | 8-bit identity and magnitude comparator |
| Number of Data Bits | 8 bits | 8 bits |
| Supported Number Formats | Binary or BCD | Binary or BCD |
| Equality Output | A=B, active-low output | A=B, active-low output |
| Greater-Than Output | A>B, active-low output | A>B, active-low output |
| Mounting Type | Through-hole | Through-hole |
| Logic Family | LS-series TTL | LS-series TTL |
מבדילים עיקריים
- Provides both equality and greater-than results (לעומתSN74LS684NE4)
- Direct binary and BCD comparison (לעומתSN74LS684NE4)
- Preserves the legacy PDIP system architecture (לעומתSN74LS684NE4)
הערות תכנון
The SN74LS684N requires a 20-pin through-hole footprint with the correct pin-1 orientation. When replacing an installed device, verify the package notch, socket orientation, and lead alignment before applying power. Keep the two 8-bit operand buses on consistent logic families so a slow or floating input cannot create an intermediate comparison result during a transition.
Account for comparator propagation delay when the result controls a clocked register, counter, or latch. If both operand buses change at the same time, the comparator can briefly observe an intermediate value while the bits settle. Add sufficient settling time or use a design that prevents invalid states from being captured, and route the A=B and A>B outputs away from noisy switching nodes.
Do not choose a 20-pin comparator solely because its pin count matches the SN74LS684N. A valid replacement must reproduce the A=B and A>B output functions, active-low polarity, supply requirements, timing behavior, and the 20-pin PDIP footprint. Related SN74LS688-family devices can have a different output set and therefore may not be drop-in replacements.
מידע על תאימות
The device is a through-hole logic IC rather than an automotive-qualified part. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation or declaration.