Texas Instruments

SN74LS684N - 8-Bit Magnitude Comparator | Texas Instruments

부품 번호: SN74LS684N ✓ 활성
PDIP-20 Package
MOQ: 1 |

SN74LS684N 개요

The Texas Instruments SN74LS684N is an 8-bit identity and magnitude comparator for binary or BCD words, with active-low A=B and A>B outputs in a 20-pin PDIP package. It compares two parallel 8-bit operands and reports whether the inputs are equal or whether the first operand is greater than the second, supporting arithmetic control, address decoding, test systems, and industrial decision logic.

A magnitude comparator is a logic IC that determines the relative ordering of two multibit numbers. It belongs to the comparator, digital logic, logic IC, and semiconductor hierarchies. Unlike a general-purpose processor or programmable controller, the SN74LS684N performs its comparison directly from wired logic inputs, so the result becomes available without firmware or instruction sequencing.

The SN74LS684N supports both binary and BCD comparison, and its active-low indication outputs are useful for driving downstream enable, reset, or selection logic. The device is listed in a 20-pin PDIP package with a 0 to 70 °C operating-temperature range. These characteristics make it appropriate for legacy-compatible equipment, industrial control systems, counters, timers, test fixtures, and interface designs that retain through-hole logic boards.

The LS series implementation uses Schottky-clamped TTL-compatible logic. Its structured outputs indicate the comparison result while external cascaded logic can extend comparison beyond the native 8-bit width. Design engineers should therefore treat the comparator outputs as active levels rather than passive status indicators, account for propagation delay when chaining stages, and use pull-up or pull-down components wherever the receiving circuit requires a defined inactive level.

Typical applications include sorting and classification control, digital test-equipment limit checking, address and threshold comparison, arithmetic-unit control, BCD instrument processing, and industrial sequence controllers. In these systems, the two operand buses feed the comparator, while its equality and greater-than outputs coordinate a counter, register, latch, or alarm without requiring continuous software polling.

A critical PCB consideration is the 20-pin PDIP footprint. Pin-1 orientation, notch direction, and adequate spacing around the package must match the board pattern, especially when repairing legacy equipment. Keep the input and output traces short enough to limit propagation-delay uncertainty, and account for the operating-temperature limits when using the part outside controlled room-temperature environments.

This product page consolidates the device identity, package information, operating range, comparison functions, sourcing structure, replacement guidance, and practical logic-design considerations into an engineering-focused reference. It also highlights the limits of direct substitution by separating true pin-compatible options from related comparator functions that do not reproduce every output and feature of the SN74LS684N.

드롭인 대체품: SN74LS684N — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

SN74LS684NE4

✅ 드롭인
📦 PDIP-20
Same 8-bit SN74LS684 function and 20-pin PDIP format; ordering-code and environmental details must be checked before substitution

📋 참조 대체품 (카탈로그에 없음)

SN74LS684N 최대 정격 & 전기적 특성

Comparator Type 8-bit identity and magnitude comparator
Number of Data Bits 8 bits
Supported Number Formats Binary or BCD
Number of Compared Inputs 2 groups of 8 bits
Equality Output A=B, active-low output
Greater-Than Output A>B, active-low output
Logic Family LS-series TTL
출력 유형 Active-low
동작 온도 범위 0 °C to 70 °C
Package Type PDIP-20
Total Pin Count 20 pins
실장 유형 Through-hole

SN74LS684N pdip-20 핀 구성 가이드

SN74LS684N(pdip-20 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.

SN74LS684N의 pdip-20 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: SN74LS684N.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

SN74LS684N 적합 용도: 6 애플리케이션s: Digital Counter Limit Detection, BCD Instrument Threshold Control, Sorting and Classification Control, Address and Threshold Decoding, Arithmetic Unit Control, Legacy Test and Measurement Equipment.

🏭

Digital Counter Limit Detection

The SN74LS684N fits counter-limit detection because it compares two complete 8-bit values in parallel and directly indicates equality or greater-than conditions. Connect the counter bus to one operand and the programmed threshold bus to the other; the active-low A=B output can qualify a selected count, while A>B can advance a sequencing stage. The 20-pin PDIP package preserves through-hole construction for legacy industrial and test equipment. Because comparison is performed in wired logic, the result does not depend on firmware polling or microcontroller instruction latency, although board-level propagation delay must be included when the counter changes rapidly.

🔧

BCD Instrument Threshold Control

The SN74LS684N is useful in BCD instrument systems that must compare an eight-digit decimal value with a stored threshold. Its binary or BCD comparison capability allows the two buses to be evaluated without software conversion, while the active-low A=B and A>B outputs can control an alarm, inhibit, or display-enable signal. This is advantageous in older measurement and panel-control equipment where a microcontroller would add unnecessary complexity. The design should preserve the documented logic levels and account for comparator delay, because BCD digits arriving from separate counters may not change simultaneously.

🏭

Sorting and Classification Control

The SN74LS684N supports sorting and classification hardware by evaluating whether an 8-bit item equals or exceeds a programmed boundary. Its equality output can initiate an accepted-item path, while the greater-than output can select a different bin or processing stage. This hard-wired approach is useful in high-throughput industrial test fixtures where a stream of encoded values must be routed according to a fixed limit. The dedicated comparator provides a deterministic hardware decision without repeated processor instructions, but the receiving registers should be clocked only after accounting for the device's propagation delay and any delays introduced by board traces.

🖥️

Address and Threshold Decoding

The SN74LS684N can decode an 8-bit address or data value against a hardware threshold when the system requires more than simple equality decoding. The A=B output identifies an exact match, while A>B supports range-style decisions when combined with additional logic. This makes the device relevant to legacy bus monitors, register validators, and industrial controllers that classify an 8-bit field without a programmable lookup table. Its through-hole PDIP-20 package is particularly useful when repairing existing boards. Confirm the output states and timing in the manufacturer documentation, and do not substitute a comparator that omits one of the required result outputs.

🔧

Arithmetic Unit Control

The SN74LS684N can provide magnitude and equality information to an arithmetic-control section in legacy digital logic. Feeding two 8-bit operands into the comparator allows a controller to determine whether an accumulator has reached a target or exceeded a limit, then use those outputs to enable a counter, latch, or carry-related function. Unlike a software comparison, the hardware result is continuously available and can participate in a combinational control path. The 0 °C to 70 °C range suits controlled commercial environments, while the 20-pin PDIP footprint supports through-hole repair and retrofit work on older arithmetic boards.

⚡

Legacy Test and Measurement Equipment

The SN74LS684N fits legacy test and measurement equipment that compares an 8-bit DUT response with a binary or BCD limit. The A=B output can indicate a passing measurement, and A>B can trigger an over-limit alarm or inhibit a subsequent test step. This dedicated hardware comparison reduces the control burden of simple fixtures and remains practical for boards designed around LS-series TTL logic. Because the PDIP-20 package uses through-hole leads, inspect existing sockets for oxidation, clean contacts, and confirm pin-1 orientation. For replacement work, verify supply voltage and timing characteristics against the original system requirements.

추천 제품 요약

SN74LS684NE4 Same-family comparator option for legacy repair designs 사용처: Digital Counter Limit Detection, BCD Instrument Threshold Control, Sorting and Classification Control, Address and Threshold Decoding, Arithmetic Unit Control, Legacy Test and Measurement Equipment
What is the SN74LS684N?
The SN74LS684N is an 8-bit identity and magnitude comparator that compares two binary or BCD words and provides active-low A=B and A>B outputs. According to the Texas Instruments SN74LS684 product information, the device is packaged as a 20-pin PDIP and is intended for parallel digital comparison applications.
What is the operating voltage of the SN74LS684N?
The SN74LS684N is an LS-series TTL comparator, but its exact recommended supply-voltage range is not stated in the manufacturer product-page snippet. Use the electrical-characteristics table in the Texas Instruments SN74LS684 datasheet before connecting the device to a system rail or designing logic-level interfaces around it.
What is the operating temperature range of SN74LS684N?
The SN74LS684N is specified for a 0 °C to 70 °C operating-temperature range. This is the commercial-temperature version of the SN74LS684 family, and the Texas Instruments part-details page identifies the N package as a 20-pin PDIP. Do not treat the device as an extended-temperature industrial part without confirming its full ordering code.
Can SN74LS684N compare BCD values?
Yes. The SN74LS684N supports comparison of two 8-bit binary or BCD words. Its A=B and A>B outputs are active low, so a low result indicates the stated comparison condition. This makes it useful in decimal instrument control, digital meters, counters, and test systems that process parallel BCD data.
Where can I download the SN74LS684N datasheet PDF?
The official starting point for the SN74LS684N datasheet is the Texas Instruments SN74LS684 product page at https://www.ti.com/product/SN74LS684?DCM=yes. The product page links ordering information, parameters, quality data, and supporting documents. Use the pin-description table and recommended operating conditions in that manufacturer documentation when assigning PCB signals.
Where is the pinout for the SN74LS684N?
The SN74LS684N uses a 20-pin PDIP package, and the authoritative pin assignment is shown in the Texas Instruments SN74LS684 datasheet. Because the available product information does not reproduce individual pin names, consult the manufacturer pin-description table before connecting comparator inputs or outputs. The package notch identifies pin 1 on a standard through-hole board.
What is the best drop-in replacement for SN74LS684N?
The closest same-brand drop-in option identified for the SN74LS684N is the SN74LS684NE4 in the same 20-pin PDIP package. A replacement should preserve the complete comparator function, output polarity, supply requirements, timing behavior, and every physical connection. Related 74LS comparator numbers cannot be assumed interchangeable because some implement different output sets.
Can SN74LS684NE4 replace SN74LS684N?
Yes, the SN74LS684NE4 is the qualified same-package candidate for replacing the SN74LS684N because both use the 20-pin PDIP format and belong to the SN74LS684 comparator family. Confirm the ordering-code details and full operating specifications in the manufacturer documentation before production use, especially when supply voltage, timing, or environmental requirements are critical.
What can replace SN74LS684N in a legacy circuit board?
A legacy-board replacement must match the SN74LS684N's 20-pin PDIP footprint and reproduce its active-low A=B and A>B outputs. The SN74LS684NE4 is the closest identified same-package option. If the board uses a surface-mount footprint, a through-hole replacement cannot be soldered directly and a PCB adaptation or alternate package must be considered.
Is SN74LS684N the same as SN74LS688N?
No. The SN74LS684N and SN74LS688N belong to the same general 8-bit comparator family, but they do not necessarily provide the same comparison outputs. The SN74LS684N is identified as an identity and magnitude comparator with A=B and A>B outputs. Confirm the complete output table and pin mapping before considering a different 74LS comparator as a substitute.
SN74LS684N vs SN74LS684NE4: which is better for a repair?
The SN74LS684NE4 is the more directly comparable choice for repairing an existing SN74LS684N board because it retains the 20-pin PDIP format and belongs to the same device family. The selection should be confirmed against the original system's timing, supply, and environmental requirements. Do not choose a comparator solely because its package has 20 pins.
When should I choose the SN74LS684N instead of a programmable comparator implementation?
Choose the SN74LS684N when the design needs a direct hardware comparison of two 8-bit buses and can use wired active-low A=B and A>B outputs. It avoids firmware, instruction latency, and microcontroller overhead. For changing bus widths, stored thresholds, complex decision trees, or user-programmable behavior, a processor or more flexible logic may be easier to maintain.
Is SN74LS684N suitable for industrial control systems?
The SN74LS684N can be suitable for a controlled industrial environment when the system remains within its 0 °C to 70 °C operating range. Its dedicated hardware comparison function is useful for counters, interlocks, thresholds, and sequence control. For wider temperature exposure, vibration, or long-life industrial requirements, select a part explicitly qualified for those conditions.
What are the key specifications of SN74LS684N that engineers should know?
The principal SN74LS684N specifications are an 8-bit comparison width, binary or BCD operation, active-low A=B and A>B outputs, a 20-pin PDIP package, and a 0 °C to 70 °C operating range. The device belongs to the LS-series TTL logic family. Supply voltage, propagation delay, and output ratings must be taken from the manufacturer electrical-characteristics table.
Where to buy SN74LS684N online?
Use the Request a Quote form on this page to request current SN74LS684N availability, commercial terms, and a quotation. The form is the appropriate channel for checking stock, quantity breaks, lead time, and order handling without relying on a static listing that may be outdated. Confirm the exact 20-pin PDIP ordering code before releasing a purchase order.
What is the lead time for SN74LS684N?
The current production and stocking lead time for SN74LS684N should be requested through the Request a Quote form on this page. Lead time can vary with order quantity, package form, and inventory status, so a generic timing statement would not be reliable. Include the target quantity and required delivery date in the request.
Is SN74LS684N in stock?
Current SN74LS684N stock status should be checked through the Request a Quote form on this page. The manufacturer lists the device for ordering, but that fact alone does not establish a live inventory quantity. Request the required quantity and packaging format so procurement can confirm allocation and dispatch timing.

엔지니어링 참조 데이터: SN74LS684N — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the SN74LS684N when a design needs a dedicated, wired-logic comparison of two 8-bit binary or BCD operands and requires active-low A=B and A>B outputs. It is especially suitable for through-hole industrial controls, test equipment, counters, and legacy arithmetic boards because the logic function is fixed and requires no firmware. The SN74LS684NE4 is the closest same-brand, same-package option for replacement inventory or repair work, subject to confirmation of its ordering details and environmental characteristics. Do not use a general SN74LS688-family part as a substitute merely because it has a related comparator function; some family members provide a different output set and therefore cannot preserve both required indications. For designs needing programmable thresholds, wider comparison, user-selectable logic, or modern low-power operation, a programmable controller or a currently specified logic family may be more appropriate than retaining the SN74LS684N.

대체품과의 비교

파라미터 이 제품 SN74LS684NE4
Brand Texas Instruments Texas Instruments
Package PDIP-20 PDIP-20
Comparator Type 8-bit identity and magnitude comparator 8-bit identity and magnitude comparator
Number of Data Bits 8 bits 8 bits
Supported Number Formats Binary or BCD Binary or BCD
Equality Output A=B, active-low output A=B, active-low output
Greater-Than Output A>B, active-low output A>B, active-low output
Mounting Type Through-hole Through-hole
Logic Family LS-series TTL LS-series TTL

주요 차별점

  • Provides both equality and greater-than results (vs SN74LS684NE4)
  • Direct binary and BCD comparison (vs SN74LS684NE4)
  • Preserves the legacy PDIP system architecture (vs SN74LS684NE4)

설계 노트

The SN74LS684N requires a 20-pin through-hole footprint with the correct pin-1 orientation. When replacing an installed device, verify the package notch, socket orientation, and lead alignment before applying power. Keep the two 8-bit operand buses on consistent logic families so a slow or floating input cannot create an intermediate comparison result during a transition.

Account for comparator propagation delay when the result controls a clocked register, counter, or latch. If both operand buses change at the same time, the comparator can briefly observe an intermediate value while the bits settle. Add sufficient settling time or use a design that prevents invalid states from being captured, and route the A=B and A>B outputs away from noisy switching nodes.

Do not choose a 20-pin comparator solely because its pin count matches the SN74LS684N. A valid replacement must reproduce the A=B and A>B output functions, active-low polarity, supply requirements, timing behavior, and the 20-pin PDIP footprint. Related SN74LS688-family devices can have a different output set and therefore may not be drop-in replacements.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The device is a through-hole logic IC rather than an automotive-qualified part. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation or declaration.

관련 검색

SN74LS684N datasheet SN74LS684N pinout SN74LS684N datasheet pdf Texas Instruments SN74LS684N SN74LS684N equivalent SN74LS684N replacement SN74LS684N cross reference SN74LS684N vs SN74LS684NE4 SN74LS684N PDIP-20 SN74LS684N 8-bit magnitude comparator SN74LS684N BCD comparison SN74LS684N price SN74LS684N stock SN74LS684N application circuit SN74LS684N comparator replacement

관련 부품 & 용어

Texas Instruments SN74LS684N SN74LS684NE4 SN74LS684 8-bit magnitude comparator identity comparator digital logic IC LS-series TTL binary comparison BCD comparison active-low output A=B output A>B output PDIP-20 through-hole package logic comparator comparator semiconductor industrial control test and measurement equipment counter limit detection address threshold decoding propagation delay operating temperature
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기