SN75117P - 5V Differential Line Transceiver | Texas Instruments
MPN: SN75117P ✓ פעילSN75117P סקירה
A differential line transceiver is an interface circuit that translates digital logic signals between a TTL-compatible system and a differential transmission line. The transmitter converts a single-ended logic input into a differential line signal, while the receiver converts the differential signal back into a single-ended TTL-compatible output. This interface hierarchy belongs to the broader class of bus transceivers, which connect digital logic ICs to communication lines.
The SN75117P is intended for bus-organized equipment where multiple transceivers can share a common line. Its three-state driver permits the driver output to be electrically disabled when another node must transmit, helping prevent bus contention when system control is correctly coordinated. The strobe control provides a way to control when the receiver output is presented to the connected logic circuit.
The implementation combines a single 5 V supply with bipolar differential line-driver and receiver functions. A listed propagation-delay value of 75 ns supports moderate-speed party-line data transfer, while the receiver-side frequency-response control permits system designers to trade response speed for improved differential noise immunity. The internal line-termination option helps control reflections on suitably designed cables or PCB interconnects.
Typical uses include industrial data buses, controller networks, test equipment, and embedded systems that need a compact TTL-to-differential interface. The device can also participate in multi-drop arrangements where node enable control is coordinated by host logic. For systems using complementary RS-485 transceivers, the interface functions remain functionally related, but modern devices may add fail-safe behavior and stronger electrostatic-discharge protection.
When laying out a board, place the transceiver near the line connector and keep the differential route short, balanced, and away from switching nodes. Confirm that enable and strobe timing cannot place two drivers on the bus simultaneously. Select external termination values from the actual cable impedance and topology rather than enabling every termination option by default.
This page combines the SN75117P interface characteristics, package information, replacement considerations, and practical bus-design guidance into a focused engineering reference. It also identifies the verified family relationship used for the available drop-in alternative and highlights functional differences that must be checked before board reuse.
חלופות תחליף ישיר עבור SN75117P — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם SN75117P (אותו גורם צורה וטביעת רגל) — שונים ב Driver Output State, Package, Transceiver Configuration.
SN75119P
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←SN75117P מפרטים
| Product Type | Differential line transceiver |
| Transceiver Configuration | 1 driver and 1 receiver per device |
| מתח אספקה | 5 V |
| Driver Input Compatibility | TTL-compatible |
| Receiver Output Compatibility | TTL-compatible |
| Driver Output State | Three-state |
| Line Operation | Differential |
| Control Function | Receiver output strobe |
| Propagation Delay | 75 ns |
| Internal Line Termination | 130 ohm equivalent |
| Receiver Frequency Response Control | User-adjustable |
| Bus Architecture | Party-line or bus-organized systems |
| מארז | 8-pin PDIP |
| סוג הרכבה | Through-hole |
| Device Technology | Bipolar |
מדריך תצורת פינים של SN75117P 8-pin pdip
תצורת פינים עבור SN75117P (מארזת 8-pin pdip). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור SN75117P.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
SN75117P מתאים עבור 6 יישוםs: Party-Line Data Bus, Industrial Controller Network, Test and Measurement Interface, Embedded Data Acquisition, Building Automation Backplane, Legacy Communication Adapter.
Party-Line Data Bus
The SN75117P fits a party-line bus because its three-state driver can release the line while another node transmits, while the differential receiver recovers the signal for TTL-compatible logic. The 5 V supply and 75 ns propagation delay suit moderate-speed control or data links. A key design requirement is arbitration: every node must maintain mutually exclusive drive states so that two enabled outputs never contend. The receiver output strobe can synchronize when the host logic reads the bus, and the 130-ohm equivalent internal termination may be used where the cable and topology make that termination appropriate.
מומלץ
Industrial Controller Network
The SN75117P can bridge a 5 V controller to a wired differential network when the installation uses a bus-organized topology. Its differential line interface improves signal transfer over a shared medium compared with an unbalanced connection, while the TTL-compatible receiver output connects directly to digital control logic. The listed 75 ns delay is appropriate for moderate-speed supervisory and status communication rather than high-rate streaming. Designers should use shielded or properly routed cable, verify the common-mode environment, and implement deterministic node-enable sequencing to prevent simultaneous transmission.
מומלץ
Test and Measurement Interface
The SN75117P is suitable for legacy test equipment that exchanges differential signals with TTL-based instrumentation while using a shared wired bus. Its receiver output strobe gives the instrument controller an explicit way to qualify the received state, and its internal 130-ohm equivalent termination can support controlled line layouts. Because this is a bipolar 5 V part, designers should verify signal levels and timing against the specific test system. Keep the cable interface away from high-energy switching nodes and validate attenuation, ringing, and noise immunity across the complete cable length.
מומלץ
Embedded Data Acquisition
The SN75117P can serve as a wired interface between embedded control logic and a multi-node acquisition network. The driver converts a TTL command into a differential line signal, and the receiver supplies a single-ended result to the controller. Its 75 ns propagation delay accommodates supervisory commands and sampled data paths that do not require modern high-speed serial performance. The frequency-response control should be evaluated if differential noise threatens decision margins. Firmware and hardware must also enforce bus ownership so that the three-state driver is not enabled while another peripheral is transmitting.
מומלץ
Building Automation Backplane
The SN75117P can be used in a building-automation backplane where controllers share a differential command line over a compact wired network. The three-state output supports node isolation during arbitration, and the 5 V operating supply is compatible with conventional digital control systems. The transmitter should be enabled only after the controller has confirmed bus ownership. Long wiring runs require careful termination and shield grounding, while the receiver's frequency-response control can help improve noise immunity. Validate fault behavior during power-up and reset because floating control states can otherwise create unintended bus activity.
מומלץ
Legacy Communication Adapter
The SN75117P is well suited to maintaining a legacy differential communication interface inside a mixed-generation adapter. It allows existing TTL-based controller logic to participate on a wired party-line bus without redesigning the host processor interface. The 5 V supply, 75 ns listed delay, and three-state outputs support conventional supervisory or low-to-moderate-speed traffic. For a new design, compare the legacy transceiver with newer RS-485 devices to determine whether fail-safe inputs and stronger electrostatic-discharge protection are required. If the original board is reused, verify strobe polarity, termination, and node-disable timing before production.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור SN75117P — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | SN75119P |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | PDIP-8 | PDIP-8 |
| Product Type | Differential line transceiver | Differential line transceiver |
| Supply Voltage | 5 V | 5 V |
| Driver and Receiver Count | 1 driver and 1 receiver | 1 driver and 1 receiver |
| Driver Output State | Three-state | Three-state |
| Control Function | Receiver output strobe | Enable-oriented control |
| Driver Input Compatibility | TTL-compatible | TTL-compatible |
| Receiver Output Compatibility | TTL-compatible | TTL-compatible |
מבדילים עיקריים
- Receiver output strobe provides direct output qualification (לעומתSN75119P)
- Single-package differential bus interface (לעומתSN75119P)
- Optional integrated line termination (לעומתSN75119P)
הערות תכנון
Coordinate driver-enable and receiver-strobe logic so that only one node drives the shared line. Two simultaneously enabled outputs can cause bus contention, distorted data, and excess current. Define safe states for reset, power-up, and watchdog recovery rather than relying on floating control inputs. If the receiver strobe is disabled, determine whether the host logic should retain its last value, enter a fault state, or request fresh bus data.
Route the differential line as a short, balanced pair with a continuous ground reference. Keep the transceiver near the connector, maintain spacing from switching-power and high-current paths, and use paired vias when changing PCB layers. Avoid long stubs because they can create reflections and unintended nodes on a party-line bus. For an 8-pin PDIP implementation, provide adequate lead spacing and avoid combining fine-pitch parts with the through-hole transceiver in the same lead-forming operation.
Treat the 130-ohm equivalent internal termination as an option, not a default requirement. Confirm cable impedance, bus length, topology, and the number of connected nodes before enabling it. Multiple terminations can over-damp the line or increase driver loading. Validate signal amplitude, ringing, and noise margin at the farthest node with the actual cable and enclosure, and use the receiver frequency-response control when noise immunity is more important than maximum response speed.
מידע על תאימות
Compliance declarations are not stated in the manufacturer page excerpt or the other technical listings. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status should be confirmed with the manufacturer or its current compliance documentation.