Texas Instruments

SN75117P - 5V Differential Line Transceiver | Texas Instruments

MPN: SN75117P ✓ فعال
5 V Vdss 8-pin PDIP Package User-adjustable Speed
MOQ: 1 |

SN75117P جائزہ

The Texas Instruments SN75117P is a 5 V differential line transceiver combining one driver and one receiver in an 8-pin PDIP package. It provides TTL-compatible driver inputs, TTL-compatible receiver outputs, three-state driver output circuitry, and a receiver output strobe for party-line or bus-organized systems. According to the manufacturer datasheet, the family also supports optional line termination through an internal 130-ohm equivalent resistor.

A differential line transceiver is an interface circuit that translates digital logic signals between a TTL-compatible system and a differential transmission line. The transmitter converts a single-ended logic input into a differential line signal, while the receiver converts the differential signal back into a single-ended TTL-compatible output. This interface hierarchy belongs to the broader class of bus transceivers, which connect digital logic ICs to communication lines.

The SN75117P is intended for bus-organized equipment where multiple transceivers can share a common line. Its three-state driver permits the driver output to be electrically disabled when another node must transmit, helping prevent bus contention when system control is correctly coordinated. The strobe control provides a way to control when the receiver output is presented to the connected logic circuit.

The implementation combines a single 5 V supply with bipolar differential line-driver and receiver functions. A listed propagation-delay value of 75 ns supports moderate-speed party-line data transfer, while the receiver-side frequency-response control permits system designers to trade response speed for improved differential noise immunity. The internal line-termination option helps control reflections on suitably designed cables or PCB interconnects.

Typical uses include industrial data buses, controller networks, test equipment, and embedded systems that need a compact TTL-to-differential interface. The device can also participate in multi-drop arrangements where node enable control is coordinated by host logic. For systems using complementary RS-485 transceivers, the interface functions remain functionally related, but modern devices may add fail-safe behavior and stronger electrostatic-discharge protection.

When laying out a board, place the transceiver near the line connector and keep the differential route short, balanced, and away from switching nodes. Confirm that enable and strobe timing cannot place two drivers on the bus simultaneously. Select external termination values from the actual cable impedance and topology rather than enabling every termination option by default.

This page combines the SN75117P interface characteristics, package information, replacement considerations, and practical bus-design guidance into a focused engineering reference. It also identifies the verified family relationship used for the available drop-in alternative and highlights functional differences that must be checked before board reuse.

کے لیے ڈراپ اِن متبادل SN75117P — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں SN75117P (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Driver Output State, Package, Transceiver Configuration.

Texas Instruments
Driver Output State: 3-state
Package: 8-pin PDIP (P)
Transceiver Configuration: 1/1 full transceiver
موازنہ کریں SN75117P →

SN75119P

✅ ڈراپ-اِن
Texas Instruments
📦 PDIP-8
Differential line transceiver · 5 V · TTL-compatible · 3-state · 3-state differential receiver · TTL-compatible · TTL-compatible · Differential line operation

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

SN75117P تفصیلات

Product Type Differential line transceiver
Transceiver Configuration 1 driver and 1 receiver per device
سپلائی وولٹیج 5 V
Driver Input Compatibility TTL-compatible
Receiver Output Compatibility TTL-compatible
Driver Output State Three-state
Line Operation Differential
Control Function Receiver output strobe
Propagation Delay 75 ns
Internal Line Termination 130 ohm equivalent
Receiver Frequency Response Control User-adjustable
Bus Architecture Party-line or bus-organized systems
پیکیج 8-pin PDIP
ماؤنٹنگ ٹائپ Through-hole
Device Technology Bipolar

SN75117P 8-pin pdip پن کنفیگریشن گائیڈ

SN75117P (8-pin pdip پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔

SN75117P کے لیے 8-pin pdip پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں SN75117P.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

SN75117P کے لیے موزوں ہے 6 ایپلیکیشنs: Party-Line Data Bus, Industrial Controller Network, Test and Measurement Interface, Embedded Data Acquisition, Building Automation Backplane, Legacy Communication Adapter.

🌐

Party-Line Data Bus

The SN75117P fits a party-line bus because its three-state driver can release the line while another node transmits, while the differential receiver recovers the signal for TTL-compatible logic. The 5 V supply and 75 ns propagation delay suit moderate-speed control or data links. A key design requirement is arbitration: every node must maintain mutually exclusive drive states so that two enabled outputs never contend. The receiver output strobe can synchronize when the host logic reads the bus, and the 130-ohm equivalent internal termination may be used where the cable and topology make that termination appropriate.

🏭

Industrial Controller Network

The SN75117P can bridge a 5 V controller to a wired differential network when the installation uses a bus-organized topology. Its differential line interface improves signal transfer over a shared medium compared with an unbalanced connection, while the TTL-compatible receiver output connects directly to digital control logic. The listed 75 ns delay is appropriate for moderate-speed supervisory and status communication rather than high-rate streaming. Designers should use shielded or properly routed cable, verify the common-mode environment, and implement deterministic node-enable sequencing to prevent simultaneous transmission.

🔧

Test and Measurement Interface

The SN75117P is suitable for legacy test equipment that exchanges differential signals with TTL-based instrumentation while using a shared wired bus. Its receiver output strobe gives the instrument controller an explicit way to qualify the received state, and its internal 130-ohm equivalent termination can support controlled line layouts. Because this is a bipolar 5 V part, designers should verify signal levels and timing against the specific test system. Keep the cable interface away from high-energy switching nodes and validate attenuation, ringing, and noise immunity across the complete cable length.

🖥️

Embedded Data Acquisition

The SN75117P can serve as a wired interface between embedded control logic and a multi-node acquisition network. The driver converts a TTL command into a differential line signal, and the receiver supplies a single-ended result to the controller. Its 75 ns propagation delay accommodates supervisory commands and sampled data paths that do not require modern high-speed serial performance. The frequency-response control should be evaluated if differential noise threatens decision margins. Firmware and hardware must also enforce bus ownership so that the three-state driver is not enabled while another peripheral is transmitting.

🧩

Building Automation Backplane

The SN75117P can be used in a building-automation backplane where controllers share a differential command line over a compact wired network. The three-state output supports node isolation during arbitration, and the 5 V operating supply is compatible with conventional digital control systems. The transmitter should be enabled only after the controller has confirmed bus ownership. Long wiring runs require careful termination and shield grounding, while the receiver's frequency-response control can help improve noise immunity. Validate fault behavior during power-up and reset because floating control states can otherwise create unintended bus activity.

🔌

Legacy Communication Adapter

The SN75117P is well suited to maintaining a legacy differential communication interface inside a mixed-generation adapter. It allows existing TTL-based controller logic to participate on a wired party-line bus without redesigning the host processor interface. The 5 V supply, 75 ns listed delay, and three-state outputs support conventional supervisory or low-to-moderate-speed traffic. For a new design, compare the legacy transceiver with newer RS-485 devices to determine whether fail-safe inputs and stronger electrostatic-discharge protection are required. If the original board is reused, verify strobe polarity, termination, and node-disable timing before production.

تجویز کردہ پروڈکٹس کا خلاصہ

SN75119P Texas Instruments استعمال ہوتا ہے: Party-Line Data Bus, Industrial Controller Network, Embedded Data Acquisition, Building Automation Backplane SN75116P Related party-line differential transceiver استعمال ہوتا ہے: Party-Line Data Bus, Test and Measurement Interface, Building Automation Backplane, Legacy Communication Adapter SN75118P Related differential bus transceiver استعمال ہوتا ہے: Industrial Controller Network, Embedded Data Acquisition SN55116P Related differential driver and receiver family استعمال ہوتا ہے: Test and Measurement Interface, Legacy Communication Adapter
What is the SN75117P?
The SN75117P is a Texas Instruments 5 V differential line transceiver with one driver and one receiver in an 8-pin PDIP package. According to the manufacturer datasheet, it provides TTL-compatible driver inputs, TTL-compatible receiver outputs, three-state driver outputs, and a receiver output strobe. It is intended primarily for party-line and bus-organized systems.
What are the key specifications of SN75117P?
The SN75117P combines a 5 V supply, one differential driver, one differential receiver, three-state driver outputs, and a receiver output strobe in an 8-pin PDIP package. The listed propagation delay is 75 ns, and the family includes a 130-ohm equivalent internal termination resistor. These characteristics position it as a moderate-speed party-line interface rather than a modern long-distance RS-485 transceiver.
Where can I download the SN75117P datasheet PDF?
The official SN75117P datasheet is available through the Texas Instruments product page at https://www.ti.com/lit/gpn/SN75117. The manufacturer document describes the differential driver, differential receiver, three-state output control, receiver strobe, frequency-response control, and optional internal line termination. Use the pin-description table and electrical-characteristics tables for final design values.
Where can I find the SN75117P pinout?
Use the pin-description table in the Texas Instruments SN75117P manufacturer datasheet to assign PCB tracks. The verified part is packaged as an 8-pin PDIP, but the exact numbered signal assignments are not reproduced on this page. Confirm pin 1 orientation against the package drawing and verify every driver, receiver, control, supply, and ground connection before fabrication.
Is SN75117P suitable for a party-line data bus?
Yes, the SN75117P is specifically intended for party-line and bus-organized systems. Its three-state driver can disable a node's line output while another node transmits, and its differential line operation supports a shared transmission medium. Reliable operation still requires a correct arbitration scheme so that two enabled drivers never contend on the same line.
What is the difference between SN75117P and SN75119P?
The principal documented difference is the control function: the SN75117 uses receiver output strobe control, while the SN75119 provides an enable-oriented control arrangement. Both belong to the same TI differential line-transceiver family and are compared as related party-line devices. Verify the control polarity, timing, and receiver-output behavior against the manufacturer datasheet before substituting one MPN in an existing circuit.
Can SN75119P replace SN75117P?
The SN75119P is the closest verified family alternative for an SN75117P replacement review because it uses the same transceiver family and comparable DIP-style implementation. Its enable control differs from the SN75117's receiver output strobe, so it is not a blind substitution: verify pin functions, control polarity, propagation timing, and bus-enable sequencing in the manufacturer datasheet before releasing production boards.
What is the best drop-in replacement for SN75117P?
The SN75119P is the only clearly identified related-family alternative for the SN75117P, and it requires control-logic verification because the enable and strobe functions differ. A broader drop-in list was not established because cross-reference pages did not confirm five additional pin-compatible devices with matching package and electrical behavior. Treat any proposed substitute as unapproved until its complete pinout and timing are checked.
Is SN75117P the same as SN75119P?
No. The SN75117P and SN75119P are related, not electrically identical, members of the TI differential line-transceiver family. The SN75117P uses receiver output strobe control, while the SN75119 uses an enable-related control arrangement. A board migration may be practical if timing and polarity are redesigned, but the control difference must be treated as a functional review item.
When should I choose SN75117P over SN75119P?
Choose the SN75117P when the existing system requires receiver output strobe behavior and has been designed around the SN75117 family interface. Choose the SN75119P when its enable-oriented architecture better matches the bus-control scheme and has passed a complete pin and timing review. The selection should be driven by control semantics, not merely by the shared differential-transceiver function.
What transmission-line termination does SN75117P provide?
The manufacturer datasheet describes an internal 130-ohm equivalent resistor that can optionally be used to terminate the transmission line. This feature is useful on appropriately designed party-line interconnects, but termination should not be enabled indiscriminately. Confirm cable impedance, node count, topology, and the resulting parallel load before using the internal terminator.
How should I control SN75117P on a shared bus?
Control the three-state driver output so that only one node drives the shared line at a time. Use the receiver output strobe to determine when the receiving logic may observe the bus, and account for its effect in the host timing. Bus contention can corrupt data and increase current, so arbitration and default power-up states should be verified in hardware.
What layout practices matter for an SN75117P design?
Route the differential line as a short, balanced pair and keep it away from clocks, switching power nodes, and other high-current paths. Place the transceiver near the cable or connector and ground the return path continuously. If the board must cross noisy regions, use paired vias and controlled spacing, then verify the completed design for ringing, reflections, and common-mode pickup.
Is SN75117P still an active product?
The Texas Instruments product page continues to provide ordering, quality, and technical-documentation links for SN75117, indicating that the family remains maintained. The exact commercial condition of the SN75117P package suffix should be checked through the Request a Quote form on this page, especially when long-term production continuity matters.
Where can I buy SN75117P and what is its price?
Use the Request a Quote form on this page to request SN75117P availability, current pricing, and lead time. The form is the appropriate route for a quote against the exact 8-pin PDIP ordering suffix. Confirm the package, quantity, and delivery requirements when submitting the request so the returned commercial information matches the intended BOM item.

کے لیے انجینئرنگ ریفرنس ڈیٹا SN75117P — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the SN75117P when maintaining a legacy party-line interface whose host logic expects a receiver output strobe, a 5 V bipolar transceiver, and three-state driver behavior. It is especially useful when the board already uses an 8-pin PDIP footprint and the cable topology can be adapted to its line characteristics. The SN75119P is the closest family alternative when enable-oriented control is easier to implement, but its control polarity and timing must be checked before substitution. For new designs requiring long cable reach, fail-safe receiver behavior, or stronger electrostatic-discharge protection, compare the SN75117P with a modern RS-485 interface rather than assuming legacy equivalence. Do not select either device until node arbitration, termination, common-mode exposure, and power-up behavior are verified.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ SN75119P
Brand Texas Instruments Texas Instruments
Package PDIP-8 PDIP-8
Product Type Differential line transceiver Differential line transceiver
Supply Voltage 5 V 5 V
Driver and Receiver Count 1 driver and 1 receiver 1 driver and 1 receiver
Driver Output State Three-state Three-state
Control Function Receiver output strobe Enable-oriented control
Driver Input Compatibility TTL-compatible TTL-compatible
Receiver Output Compatibility TTL-compatible TTL-compatible

اہم امتیازی خصوصیات

  • Receiver output strobe provides direct output qualification (بمقابلہSN75119P)
  • Single-package differential bus interface (بمقابلہSN75119P)
  • Optional integrated line termination (بمقابلہSN75119P)

ڈیزائن نوٹس

Coordinate driver-enable and receiver-strobe logic so that only one node drives the shared line. Two simultaneously enabled outputs can cause bus contention, distorted data, and excess current. Define safe states for reset, power-up, and watchdog recovery rather than relying on floating control inputs. If the receiver strobe is disabled, determine whether the host logic should retain its last value, enter a fault state, or request fresh bus data.

Route the differential line as a short, balanced pair with a continuous ground reference. Keep the transceiver near the connector, maintain spacing from switching-power and high-current paths, and use paired vias when changing PCB layers. Avoid long stubs because they can create reflections and unintended nodes on a party-line bus. For an 8-pin PDIP implementation, provide adequate lead spacing and avoid combining fine-pitch parts with the through-hole transceiver in the same lead-forming operation.

Treat the 130-ohm equivalent internal termination as an option, not a default requirement. Confirm cable impedance, bus length, topology, and the number of connected nodes before enabling it. Multiple terminations can over-damp the line or increase driver loading. Validate signal amplitude, ringing, and noise margin at the farthest node with the actual cable and enclosure, and use the receiver frequency-response control when noise immunity is more important than maximum response speed.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

Compliance declarations are not stated in the manufacturer page excerpt or the other technical listings. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status should be confirmed with the manufacturer or its current compliance documentation.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-09 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

SN75117P datasheet SN75117P datasheet pdf SN75117P pinout SN75117P schematic SN75117P equivalent SN75117P replacement SN75117P cross reference SN75117P vs SN75119P SN75117P PDIP-8 footprint SN75117P 5V transceiver SN75117P application circuit SN75117P price SN75117P stock Texas Instruments SN75117P

متعلقہ اجزاء اور اصطلاحات

Texas Instruments SN75117P SN75119P SN75116P SN75118P SN55116P differential line transceiver bus transceiver line driver differential receiver three-state driver TTL-compatible logic party-line bus bus-organized system receiver output strobe frequency-response control 130-ohm termination 5 V supply 75 ns propagation delay PDIP-8 through-hole package digital interface communication line common-mode voltage
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں