TAS5182IDCA - 100W Stereo Class-D Audio Controller
MPN: TAS5182IDCA ✗ סוף ייצורTAS5182IDCA סקירה
A digital amplifier power-stage controller is an integrated circuit that interprets an audio input and generates gate-drive signals for external switching MOSFETs. Unlike a conventional analog audio power amplifier, the TAS5182IDCA places the high-voltage and high-current switching function in discrete transistors. This separates signal processing from power conversion, allowing the external MOSFET stage to determine much of the amplifier's voltage, current, thermal, and output-power capability. The controller therefore belongs to the Class-D amplifier, digital audio amplifier, power-management IC, and semiconductor hierarchy.
The 2 × 100 W capability at 6 V describes controller-supported BTL operation rather than the output of an integrated monolithic power stage. Engineers must select suitable N-channel power MOSFETs, a power-supply arrangement, an output filter, and a thermal design that match the target impedance and enclosure. The low typical distortion figure makes the controller appropriate for music reproduction systems where audible waveform deviation should remain low across the audio band.
The TAS5182 architecture is intended to work with discrete bridge-tied-load output stages. In each half-bridge, the controller drives the gates of the high-side and low-side MOSFETs with complementary signals. External LC output filtering converts the switched full-bridge waveform into a filtered analog output capable of driving a loudspeaker through a BTL network. Correct gate voltage, dead time, switching speed, and layout continuity are therefore essential to the controller's real-world performance.
Typical uses include home-theater amplifiers, powered subwoofers, active loudspeakers, compact stereo systems, and other high-power Class-D audio products. The controller can also serve multi-channel systems when each stereo pair is assigned to separate channels. Compared with a monolithic amplifier, the discrete-MOSFET approach offers greater freedom in output-device selection, thermal partitioning, and power scaling, but it also increases design complexity and EMI sensitivity.
PCB implementation requires short gate-drive loops, careful high-current return paths, a continuous output-filter ground reference, and separation between sensitive input and switching nodes. Place input, supply, and compensation components close to their associated pins. Use thermal vias beneath exposed-pad structures where applicable and verify the selected MOSFETs, inductor, and capacitor ratings against the intended 6 V BTL operating point. EMI filtering must be evaluated together with the switching layout rather than added only after enclosure testing.
This product page combines the controller's verified power and distortion ratings with package information, application guidance, drop-in family comparisons, and practical PCB design notes. It is intended to accelerate engineering selection while making the system-level responsibilities of an external-MOSFET Class-D output stage explicit.
חלופות תחליף ישיר עבור TAS5182IDCA — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם TAS5182IDCA (אותו גורם צורה וטביעת רגל) — שונים ב Mounting Type, Package, Product Type, Output Configuration, Typical THD+N.
TAS5182IDCAG4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TAS5182IDCARG4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TAS5182DCAG4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TAS5182DCAR
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←TAS5182DCA
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←TAS5182IDCA דירוגים מרביים ומאפיינים חשמליים
| Product Type | Stereo digital amplifier power-stage controller |
| Amplifier Class | Class D |
| Channel Count | 2 channels |
| תצורת מוצא | Bridge-tied load (BTL) |
| Maximum Rated Stereo Output Power | 2 × 100 W RMS at 6 V |
| Power per Channel | Up to 100 W RMS at 6 V |
| Typical THD+N | < 0.15% at 1 kHz |
| Output Stage | External discrete MOSFET bridge-tied-load stage |
| מארז | 56-pin HTSSOP |
| מספר פינים | 56 pins |
| סוג הרכבה | Surface mount |
מדריך תצורת פינים של TAS5182IDCA 56-pin htssop
תצורת פינים עבור TAS5182IDCA (מארזת 56-pin htssop). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור TAS5182IDCA.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
TAS5182IDCA מתאים עבור 6 יישוםs: Home-Theater Stereo Power Amplifier, Powered Subwoofer Amplifier, Active Loudspeaker, Multi-Channel Audio Amplifier, Compact Hi-Fi Power Stage, Professional Audio Power Module.
Home-Theater Stereo Power Amplifier
TAS5182IDCA fits a two-channel home-theater power amplifier built around external MOSFET output stages. Its controller platform supports up to 100 W RMS per channel at 6 V in bridge-tied-load operation, while typical THD+N below 0.15% at 1 kHz provides a useful starting point for low-distortion music amplification. The design requires complementary gate drives, carefully selected power MOSFETs, an LC speaker-output filter, and a supply rated for the target output. Keeping those power components outside the controller permits flexible thermal sizing and PCB partitioning. However, the engineer must validate the complete loop because PCB inductance, filter response, MOSFET switching behavior, and speaker impedance determine the final performance.
מומלץ
Powered Subwoofer Amplifier
TAS5182IDCA can control a high-power stereo subwoofer output stage when the amplifier uses a 6 V BTL arrangement and external N-channel MOSFETs. The two channels provide flexibility for balanced or parallel speaker drives, and the controller's 100 W-per-channel rating allows substantial continuous output when the supply and thermal design support it. Typical THD+N below 0.15% at 1 kHz is valuable for reproducing low-frequency musical content with low waveform error. In practice, the output inductor must be selected for the intended speaker impedance, the DC blocking and EMI network must be stable, and the MOSFET switching transitions must remain thermally manageable.
מומלץ
Active Loudspeaker
TAS5182IDCA is suitable for an active stereo loudspeaker because it controls two external MOSFET bridges and can support up to 100 W RMS per channel at 6 V. The controller approach allows the amplifier board to be tailored around the selected loudspeaker impedance rather than accepting the thermal limits of a monolithic output stage. Audio input conditioning, gain setting, protection, and crossover functions can be integrated around the controller in the signal path. The major engineering trade-off is increased switching-stage complexity: power-MOSFET selection, gate resistance, output filtering, thermal vias, and EMI control all require careful implementation to preserve the low typical distortion of the controller platform.
מומלץ
Multi-Channel Audio Amplifier
TAS5182IDCA can form the basis of a multi-channel amplifier by assigning each stereo controller section to a separate pair of amplification channels. Its two-channel architecture supports compact implementations of surround-sound or multi-zone audio products, while the external-MOSFET configuration permits output power and thermal performance to be scaled for each board. At the system level, each controller still requires its own output filters and protection strategy, while shared supplies must account for the combined switching and thermal load. The low typical THD+N figure below 0.15% at 1 kHz supports high-fidelity reproduction, but channel-to-channel matching and inter-channel EMI should be checked using the final analog and power layouts.
מומלץ
Compact Hi-Fi Power Stage
TAS5182IDCA is appropriate for a compact high-fidelity power stage when discrete MOSFETs are used to separate amplification current from the controller's signal-processing function. Supporting up to 100 W RMS per channel at 6 V gives the designer room to match different speaker sensitivities and enclosure limits, while typical THD+N below 0.15% at 1 kHz provides a useful distortion baseline. Component value selection, bootstrap or supply circuitry, and protection thresholds must be matched to the chosen MOSFETs. Thermal performance depends on copper area, thermal vias, airflow, and the operating duty cycle, so a nominal controller rating alone should not be treated as a guaranteed continuous output for every enclosure.
מומלץ
Professional Audio Power Module
TAS5182IDCA can serve as the control element in a professional-audio power module when the external MOSFET bank, transformer or supply system, output network, and protection circuitry are designed for professional loads. The 2 × 100 W RMS capability at 6 V and typical THD+N below 0.15% at 1 kHz provide a strong basis for a high-efficiency Class-D module. Because the controller does not contain the power transistors, designers can select devices according to voltage, current, SOA, and thermal requirements rather than accepting a fixed integrated output stage. Practical deployment still requires acoustic and electrical safety review, output DC-offset protection, robust grounding, and thermal validation under sustained program material.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור TAS5182IDCA — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | TAS5182IDCAG4 | TAS5182IDCARG4 | TAS5182DCAG4 | TAS5182DCAR | TAS5182DCA |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 56-pin HTSSOP | 56-pin HTSSOP | 56-pin HTSSOP | 56-pin HTSSOP | 56-pin HTSSOP | 56-pin HTSSOP |
| Product Type | Stereo digital amplifier power-stage controller | Stereo digital amplifier power-stage controller | Stereo digital amplifier power-stage controller | Stereo digital amplifier power-stage controller | Stereo digital amplifier power-stage controller | Stereo digital amplifier power-stage controller |
| Amplifier Class | Class D | Class D | Class D | Class D | Class D | Class D |
| Channel Count | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Output Configuration | Bridge-tied load (BTL) | Bridge-tied load (BTL) | Bridge-tied load (BTL) | Bridge-tied load (BTL) | Bridge-tied load (BTL) | Bridge-tied load (BTL) |
| Rated Stereo Output Power | 2 × 100 W RMS at 6 V | 2 × 100 W RMS at 6 V | 2 × 100 W RMS at 6 V | 2 × 100 W RMS at 6 V | 2 × 100 W RMS at 6 V | 2 × 100 W RMS at 6 V |
| Typical THD+N | < 0.15% at 1 kHz | < 0.15% at 1 kHz | < 0.15% at 1 kHz | < 0.15% at 1 kHz | < 0.15% at 1 kHz | < 0.15% at 1 kHz |
| External MOSFET Output Stage | Required | Required | Required | Required | Required | Required |
| Ordering Suffix | IDCA | IDCAG4 | IDCARG4 | DCAG4 | DCAR | DCA |
מבדילים עיקריים
- Supports two high-power channels from one controller (לעומתTAS5086DBTR)
- Documented complete ordering-family replacement (לעומתTAS5182IDCAG4)
- Low typical audio-band distortion for external-MOSFET architecture (לעומתTAS5182DCAR)
- External power-device flexibility (לעומתTAS5086DBTR)
הערות תכנון
Keep each gate-drive loop compact and route the controller ground reference close to the external MOSFET source connections. Long gate traces and shared high-current return paths can increase switching transients, ringing, and distortion. Use symmetrical routing for the two half-bridges, maintain adequate spacing from sensitive analog inputs, and cross-check the 56-pin land pattern against the exact package drawing before releasing artwork.
The 2 × 100 W RMS rating at 6 V applies to a complete external-MOSFET BTL design. Select the supply, MOSFETs, output inductor, and capacitors for the intended speaker impedance rather than using the controller rating alone. Account for continuous real-world dissipation, amplifier efficiency, transient headroom, and protection behavior. Validate the assembled amplifier at the target load because PCB and thermal limitations can reduce practical output below the nominal rating.
The controller's primary thermal challenge depends on the selected external devices and the copper area connected to exposed structures. Provide thermal vias and uninterrupted copper beneath the package where the manufacturer land pattern calls for them, then size the MOSFET heat spreading around each output bridge. Use estimated junction-temperature calculations from the actual dissipation, thermal resistance, and ambient temperature before increasing output power or reducing enclosure ventilation.
Treat switched output nodes as high-voltage, high-current EMI sources even though the controller itself does not contain the output transistors. Keep the output-filter components close to the power bridge, minimize the switched-node area, and maintain a clean return reference for the analog input and control circuitry. Evaluate conducted and radiated emissions after the MOSFET gates, output network, protective elements, and enclosure are finalized.
Do not interpret 100 W per channel as a guaranteed speaker output independent of load impedance. The BTL topology, speaker impedance, output filter, supply voltage, and MOSFET dissipation determine usable power and stability. Also verify that any replacement uses the correct exposed-pad and thermal requirements; a matching 56-pin outline alone does not guarantee that every footprint feature and electrical condition is interchangeable.
מידע על תאימות
The TAS5182 is an audio power-stage controller for consumer and industrial equipment, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified. AEC-Q100 is not applicable to the standard TAS5182IDCA ordering option.