TCA0372DWR2 - Dual Power Op-Amp 1A SOIC-16 | onsemi
MPN: TCA0372DWR2 ✓ פעילTCA0372DWR2 סקירה
A power operational amplifier is an op-amp that combines the precision input stage and high open-loop gain of a standard operational amplifier with an output stage capable of sourcing or sinking currents in the ampere range, far beyond the tens of milliamps typical of general-purpose op-amps. In the power-management and signal-chain hierarchy, the TCA0372 sits between standard op-amps and fully integrated audio or motor driver ICs: it is an amplifier - specifically a power op-amp - classified under operational amplifiers / buffer amplifiers in vendor taxonomies.
Key differentiating features of the TCA0372 include the 1.0 A continuous output current rating, a gain-bandwidth product around 1.4 MHz with a 1.4 V/us slew rate, and operation on a single supply from 5 V to 40 V or on dual supplies up to ±20 V. The device is internally compensated and, critically, exhibits no deadband crossover distortion in the output stage, which is essential when driving inductive loads such as coils, actuators, and servo motors where crossover artifacts translate directly into torque ripple or audible distortion.
Architecturally, the TCA0372 is a monolithic bipolar device integrating two complete power op-amp channels on a single die. The wide-body SOIC-16 package provides substantially better thermal dissipation than a standard SOIC-8, allowing both channels to drive heavy loads when adequate PCB copper is provided. Internal thermal limiting and safe-area considerations typical of power output stages protect the device during faults, though board-level thermal design remains the designer's responsibility at sustained high current.
Typical applications include servo amplifiers for position control, power supplies as error amplifiers or pass-element drivers, coil and solenoid drivers, motor control subcircuits, audio power output stages, and general power buffering where a standard op-amp cannot supply the required load current.
When designing with the TCA0372, account for package power dissipation: at 1 A output across a large input-to-output voltage differential, junction temperature rise is dominated by the SOIC-16 thermal resistance, so generous copper pours on the output-stage pins are recommended.
This page adds value beyond the manufacturer datasheet by consolidating drop-in replacement options (TCA0372DWR2G, TCA0372BDWR2G, NCV0372B variants), application guidance, and comparison data in one place for sourcing and design engineers.
חלופות תחליף ישיר עבור TCA0372DWR2 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם TCA0372DWR2 (אותו גורם צורה וטביעת רגל) — שונים ב Crossover Distortion, Package, Slew Rate.
TCA0372DWR2G
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TCA0372BDWR2G
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TCA0372DWG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←NCV0372BDWR2G
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TCA0372DWR2
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←TCA0372DWR2 דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Dual Power Operational Amplifier |
| Number of Circuits | 2 |
| Output Current per Channel | 1.0 A |
| Supply Voltage Range (Single) | 5 V to 40 V |
| Supply Voltage Range (Dual) | ±20 V (40 V total) |
| Gain Bandwidth Product | 1.4 MHz |
| Slew Rate | 1.4 V/us |
| Crossover Distortion | No deadband |
| מארז | SOIC-16 Wide (DW) |
| סוג הרכבה | Surface Mount |
| Packaging | Tape and Reel (R2 suffix) |
| מספר פינים | 16 |
| Extended Temperature Variant | TCA0372DWR2G (extended temp, Pb-free) |
| Manufacturer Lifecycle | Active (per onsemi product page) |
| Typical Applications | Servo amplifiers, power supplies, coil drivers |
מדריך תצורת פינים של TCA0372DWR2 soic-16 wide (dw)
תצורת פינים עבור TCA0372DWR2 (מארזת soic-16 wide (dw)). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור TCA0372DWR2.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
TCA0372DWR2 מתאים עבור 6 יישוםs: Servo Amplifiers, Power Supply Error Amplifier / Pass Driver, Coil and Solenoid Drivers, Audio Power Output Stage, Motor Control Subcircuits, Instrumentation Power Buffering.
Servo Amplifiers
The TCA0372DWR2 is explicitly named by onsemi as intended for servo amplifiers, and the part's specifications align precisely with that role. Servo loops drive motor and actuator coils where the amplifier output stage must deliver ampere-level current while remaining linear through zero crossing: any deadband in the output stage appears as torque ripple and positioning error. The TCA0372's no-deadband crossover distortion output stage addresses this directly, and its 1.0 A per-channel output current drives small servo windings without an external driver stage. Operation on single 5-40 V or dual ±20 V supplies fits both industrial split-rail drives and single-supply actuators. Designers should size PCB copper on the output pins for the sustained coil current and verify loop stability with the reactive load using the datasheet compensation guidance.
מומלץ
Power Supply Error Amplifier / Pass Driver
onsemi lists power supplies among the TCA0372's target applications. In a linear or servo-controlled switching supply, the error amplifier must both process small feedback signals and, in low-dropout or linear designs, drive the base or gate of a series pass element with meaningful current. The TCA0372DWR2 combines a standard op-amp input stage with a 1.0 A output, so a single device can close the loop and directly drive the pass transistor at moderate loads. Its 5-40 V single-supply range covers common 12 V, 24 V, and 28 V industrial rails, while ±20 V dual-supply operation suits bench and laboratory supplies. Designers should confirm phase margin with the pass element's input capacitance and keep the amplifier's dissipation within the SOIC-16 wide package thermal limits.
מומלץ
Coil and Solenoid Drivers
Driving coils, solenoids, and electromagnets is a core TCA0372 use case, enabled by three parameters: 1.0 A continuous output current per channel, the no-deadband crossover output stage, and internally compensated stability with inductive loads. When a solenoid energizes and releases, the inductive kick must be handled - the datasheet typical applications show the output stage paired with appropriate flyback protection, and the dual channels allow H-bridge-style bidirectional coil drive on ±20 V supplies for latching actuators. Compared with discrete transistor driver chains, the monolithic approach removes crossover artifacts from the current waveform, which matters in proportional solenoids used in fluid control where ripple translates into pressure modulation. Verify thermal dissipation at the coil holding current.
מומלץ
Audio Power Output Stage
The TCA0372DWR2 functions as a compact dual-channel audio power amplifier for small speakers and headphone-driver applications. Its no-deadband crossover distortion specification is the decisive audio parameter: Class-B-style output stages produce audible crossover distortion at low signal levels, while the TCA0372's output stage remains linear through the zero-current crossing, preserving low-level detail. With 1.0 A per channel on ±15 V rails, the device drives typical 8-ohm small-speaker loads at useful output levels, and the dual channels support stereo operation from one SOIC-16 package. Bandwidth of the 1.4 MHz family is ample for audio closed-loop gains of 20-40 dB. Place the device close to bulk supply decoupling and provide generous copper on the output pins for sustained program material.
מומלץ
Motor Control Subcircuits
Within larger motor-control systems, the TCA0372DWR2 fills the analog layer between the digital controller and the power stage. It can drive small DC motor windings directly, act as the error amplifier inside velocity or position loops, or buffer DAC-generated torque commands up to ampere levels - a role general-purpose op-amps cannot perform because of their milliamp-class outputs. The 1.4 MHz-class bandwidth family supports typical closed-loop control bandwidths, and single 5-40 V operation allows the amplifier to share the motor rail. For bidirectional drive, the two channels configure as a linear H-bridge on ±20 V supplies. Designers should validate stability with the motor's inductance and back-EMF characteristics and budget package dissipation at stall current, which is the worst-case thermal point.
מומלץ
Instrumentation Power Buffering
Test, measurement, and industrial instrumentation frequently need an op-amp output that supplies real load current: reference buffers feeding calibration loads, transducer excitation drives, and programmable source outputs. The TCA0372DWR2 provides the answer by pairing a conventional precision-style input stage with a 1.0 A output stage in one package, allowing a standard feedback network to be wrapped around an ampere-class driver. The wide SOIC-16 package thermally supports sustained buffering better than small-outline alternatives, and ±20 V dual-supply operation spans common instrument analog rails. In data-acquisition front ends, pairing the buffer with a precision ADC channel lets the system verify its own output. Keep feedback resistances moderate and confirm capacitive-load stability for cable-driven outputs.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור TCA0372DWR2 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | TCA0372DWR2G | TCA0372BDWR2G | TCA0372DWG | NCV0372BDWR2G |
|---|---|---|---|---|---|
| Package | SOIC-16 Wide (DW) | SOIC-16 Wide (DW) - same | SOIC-16 Wide (WSOIC-16) - same | SOIC-16 Wide (DW) - same | SOIC-16 Wide (DW) - same |
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi |
| Output Current per Channel | 1.0 A | 1.0 A | 1.0 A | 1.0 A | 1.0 A |
| Supply Voltage Range | 5 V to 40 V | 5 V to 40 V | 5 V to 40 V | 5 V to 40 V | 5 V to 40 V |
| Crossover Distortion | No deadband | No deadband | No deadband | No deadband | No deadband |
| Automotive Qualification | No | No | No | No | Yes (NCV = automotive) |
מבדילים עיקריים
- Ampere-class output in an op-amp footprint (לעומתLM2904PWR)
- No-deadband crossover distortion output stage (לעומתTCA0372BDWR2G (B-grade Class-B style alternatives))
- Pb-free and automotive variants on the identical footprint (לעומתNCV0372BDWR2G / TCA0372DWR2G)
הערות תכנון
The TCA0372DWR2 dissipates power as (VSUPPLY - VOUT) x ILOAD in the output transistors. Estimated: at a 40 V rail driving a grounded 10-ohm load at 1 A, dissipation approaches 30 W - far beyond the SOIC-16 wide package's capability. Keep the input-to-output voltage differential modest at high load currents, use wide copper pours connected to the output and supply pins, and check the datasheet thermal derating curves against your worst-case continuous load, not just typical operation. For bipolar drive on dual supplies, both halves of the waveform must be budgeted.
On the SOIC-16 wide footprint, dedicate generous PCB copper to the supply and output pins since the package has no exposed thermal pad - all heat exits through the leads. Place bulk decoupling (tens of microfarads, per the datasheet typical application circuits) within centimeters of the supply pins and add 0.1 uF ceramics directly at the pins for high-frequency bypass. Route the feedback network away from the high-current output trace to prevent parasitic coupling from destabilizing the loop, and keep the inverting-node track as short as possible.
Driving reactive loads (coils, solenoids, motors) is the intended use, but inductive kickback must be contained: provide flyback or clamp paths per the onsemi datasheet application circuits so load transients do not drive the output beyond the supply rails. Never exceed 40 V total supply under transient conditions. When replacing TCA0372DWR2 with the B-grade or NCV variants, verify the offset and bandwidth figures of the replacement grade against the circuit's accuracy and loop-bandwidth requirements rather than assuming complete parameter equivalence.
מידע על תאימות
The G-suffix variants (TCA0372DWR2G, TCA0372BDWR2G, TCA0372DWG) are onsemi's Pb-free finish parts; the non-G TCA0372DWR2 finish status should be confirmed on the onsemi product page material declaration before use in regulated markets.