THS7303PW - 3-Channel Low-Power Video Amplifier | TI
MPN: THS7303PW ✗ סוף ייצורTHS7303PW סקירה
A video amplifier is an analog signal-conditioning IC that increases the amplitude and drive capability of composite, component, or other video signals. It belongs to the broader hierarchy of amplifier ICs, analog integrated circuits, and signal-chain semiconductors. The THS7303PW combines three buffered video channels with programmable control, allowing a compact design to select filtering, gain, multiplexer routing, and bias behavior without replacing multiple fixed-function devices.
Its principal features include three integrated video amplifiers, a 2:1 input multiplexer, a selectable 6 dB gain setting, selectable low-pass filters, SAG correction, and an I2C interface. These functions support programmable video paths in set-top boxes, video processors, display equipment, surveillance systems, and general-purpose analog-to-digital signal-processing circuits. Low power consumption is particularly useful when three active video channels must operate continuously in compact commercial or industrial equipment.
The THS7303PW uses a complementary silicon-germanium BiCom-III process according to the manufacturer documentation. Its approximately 190 MHz small-signal bandwidth and 320 V/µs slew rate provide ample speed for high-frequency video signals. The 2.1:1 power-supply current and 6 mA quiescent current reported in the device documentation describe a low-power design intended to balance drive strength, integration, and heat management in a surface-mount package.
Typical uses include conditioning composite video for digitization, buffering multiple video outputs, switching between two input sources with a 2:1 multiplexer, and applying programmable filter or gain settings in display and broadcast equipment. The I2C control interface also enables software-controlled configuration of multiple channels in systems where the video path changes during operation.
PCB design should preserve the short, controlled return paths needed by high-speed analog signals. Place input and output bypass capacitors close to the relevant supply and ground pins, keep video traces away from switching nodes and digital control lines, and follow the pin descriptions and layout guidance in the manufacturer datasheet. Bus pull-up resistors and series damping should be selected to keep SCL and SDA waveforms within valid limits.
This page organizes the THS7303PW’s functions, pin-compatible replacement information, comparison parameters, application guidance, and practical design considerations. It supports faster component evaluation by placing the device’s key architectural features alongside the engineering checks required for reliable video-signal implementation.
חלופות תחליף ישיר עבור THS7303PW — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
THS7303PWG4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
THS7303PW דירוגים מרביים ומאפיינים חשמליים
| Number of Channels | 3 channels |
| Device Type | 3-channel low-power video amplifier with 2:1 input multiplexer |
| Supply Voltage Range | 2.7 V to 5 V |
| Small-Signal Bandwidth | 190 MHz at -3 dB |
| Slew Rate | 320 V/µs |
| זרם אספקה | 18.9 mA |
| זרם מנוחה | 6 mA |
| Gain Options | Selectable 6 dB gain |
| Input Multiplexer Ratio | 2:1 |
| Control Interface | I2C |
| Filter Configuration | Selectable filters |
| Video Correction | SAG correction |
| Input Bias | Selectable input bias modes |
| סוג פלט | Rail-to-rail |
| Process Technology | Complementary silicon-germanium BiCom-III |
| Number of Terminals | 20 terminals |
| מארז | 20-pin TSSOP (PW) |
| Package Form | Rectangular gull-wing |
| Temperature Grade | Industrial |
| סוג הרכבה | Surface mount |
מדריך תצורת פינים של THS7303PW rectangular gull-wing
תצורת פינים עבור THS7303PW (מארזת rectangular gull-wing). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור THS7303PW.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
THS7303PW מתאים עבור 6 יישוםs: Composite Video Conditioning, Video Multiplexing, Set-Top Box Video Paths, Security Camera Video Buffering, Display Interface Conditioning, Industrial Video Processing.
Composite Video Conditioning
The THS7303PW is well suited to conditioning composite video before digitization because it combines a 190 MHz small-signal bandwidth, 320 V/µs slew rate, selectable filters, and 6 dB gain in one device. A channel can be configured for the required bandwidth and gain, then drive the input of an ADC or video processor. The 2:1 multiplexer also allows a source selector to share one downstream signal chain. Designers should verify the composite video timing, output loading, synchronization behavior, and input/output voltage limits against the application before production use.
מומלץ
Video Multiplexing
The THS7303PW can select between two video inputs with its 2:1 multiplexer, reducing the number of external routing components required in compact video systems. Its three amplifier channels allow multiple routed or buffered outputs, while I2C control permits software changes to gain, filters, bias modes, and routing. For a dual-source front end, the device can sit between source buffers and an ADC or display interface. Validate switch timing, channel crosstalk, output settling, and the exact supported I2C configuration sequence in the final signal chain.
מומלץ
Set-Top Box Video Paths
A set-top box can use the THS7303PW to condition several video signals while keeping board area and control complexity manageable. Three integrated channels, a 2.7 V to 5 V single supply, approximately 6 mA quiescent current, and I2C programmability fit low-power consumer equipment. The selectable filters and 6 dB gain provide flexible channel configuration for different source stages. Layout work should keep the high-speed video traces short, place bypass capacitors near the device, and isolate the I2C and video paths from switching regulators.
מומלץ
Security Camera Video Buffering
The THS7303PW can buffer and condition camera video signals in surveillance systems requiring multiple amplifier stages or programmable source selection. Its 190 MHz bandwidth and 320 V/µs slew rate support high-speed analog video, while the selectable filters, gain, bias modes, and SAG correction allow channel settings to be adapted to different source characteristics. The low-power 2.7 V to 5 V architecture also suits compact camera electronics. Confirm video standard timing, input levels, output drive, channel-to-channel isolation, and temperature performance before deploying the device in a camera housing.
מומלץ
Display Interface Conditioning
The THS7303PW is applicable in display interfaces where multiple analog video paths require buffering, gain adjustment, and filtering. The three amplifier channels can be organized for separate source or routing stages, and the 2:1 multiplexer can select between two inputs without duplicating downstream circuitry. Its rail-to-rail output characteristic and programmable configuration support compact interface designs, subject to the exact output-voltage and load limits in the datasheet. PCB planning should reserve a continuous ground reference and minimize stubs beneath the TSSOP footprint.
מומלץ
Industrial Video Processing
Industrial inspection and machine-vision systems can use the THS7303PW to condition analog video before conversion or analysis. Its configurable filters and 6 dB gain help tailor each channel, while SAG correction addresses signal-amplitude variations that may occur in industrial video paths. The 2:1 multiplexer supports selectable test and production inputs, and the I2C interface permits centralized configuration. For reliable operation, validate settling time, channel synchronization, noise margin, temperature range, and grounding around sensitive analog inputs in the complete machine-vision front end.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור THS7303PW — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | THS7303PWG4 |
|---|---|---|
| Package | 20-pin TSSOP (PW) | 20-pin TSSOP (PW) |
| Brand | Texas Instruments | Texas Instruments |
| Number of Channels | 3 channels | 3 channels |
| Small-Signal Bandwidth | 190 MHz at -3 dB | 190 MHz at -3 dB |
| Slew Rate | 320 V/µs | 320 V/µs |
| Supply Voltage Range | 2.7 V to 5 V | 2.7 V to 5 V |
| Supply Current | 18.9 mA | 18.9 mA |
| Quiescent Current | 6 mA | 6 mA |
| Input Multiplexer | 2:1 | 2:1 |
| Control Interface | I2C | I2C |
| Gain | Selectable 6 dB | Selectable 6 dB |
| Special Functions | Selectable filters, SAG correction, selectable input bias modes | Selectable filters, SAG correction, selectable input bias modes |
מבדילים עיקריים
- Three programmable video channels in one package (לעומתTHS7303PWG4)
- Integrated 2:1 input multiplexing (לעומתTHS7303PWG4)
- Programmable analog configuration (לעומתTHS7303PWG4)
הערות תכנון
Treat the THS7303PW as a high-speed analog device even though its interface is digital. Place input, output, and bypass connections directly adjacent to their associated pins, maintain a continuous ground reference, and avoid routing SCL or SDA beneath the package. The manufacturer datasheet should control trace geometry, impedance, decoupling, and exposed or adjacent thermal considerations.
Follow the manufacturer’s recommended bypass-capacitor network and place each capacitor on the same side of the PCB as its associated supply pin. Keep the supply return path short and use a quiet source where video signal purity is important. Confirm that the 2.7 V to 5 V operating range includes startup, ripple, and output-voltage conditions across temperature.
Do not treat the 2:1 multiplexer as a general-purpose high-voltage switch or the I2C interface as a high-capacitance bus driver. Check input levels, output loading, channel timing, and register behavior for the exact application. A bus that becomes unstable when the amplifier is connected should be examined for pull-up strength, capacitance, clock stretching, and level compatibility rather than increasing resistance blindly.
Use short video paths and controlled terminations or impedance management appropriate to the source and receiver. Keep switching-regulator paths and high-current return currents away from the video inputs, and provide a direct ground return for each decoupling capacitor. Validate eye quality, ringing, settling, and channel-to-channel skew at the intended clock or video frequency.
מידע על תאימות
The device is identified as an industrial-grade video amplifier. No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was established.