NXP Semiconductors

TJA1443ATK/0Z - 5Mbit/s CAN FD Transceiver | NXP

MPN: TJA1443ATK/0Z ✓ פעיל
4.5 V to 5.5 V Vdss SAE J2284-1 to SAE J2284-5 Rds(on) 14-terminal HVSON, approximately 3 mm x 4.5 mm Package
כמות הזמנה מינימלית: 1 |

TJA1443ATK/0Z סקירה

The NXP Semiconductors TJA1443ATK/0Z is a high-speed CAN and CAN FD transceiver with a data rate up to 5 Mbit/s, a 4.5 V to 5.5 V supply range, and a 14-terminal HVSON surface-mount package. It provides the physical-layer interface between a CAN controller and a two-wire CAN bus, with VIO, ENABLE, standby, and error-control functions identified in the product listing.

A high-speed CAN transceiver is an interface integrated circuit that converts logic-level controller signals into the dominant and recessive voltage states used on a CAN bus. The TJA1443 belongs to the broader network-interface hierarchy: CAN transceiver, physical-layer interface, interface IC, and semiconductor. Its implementation supports high-speed Classical CAN and CAN FD systems while simplifying conversion between a digital CAN controller and the bus wiring.

The principal operating features include a maximum listed signaling rate of 5 Mbit/s, a 4.5 V to 5.5 V core-supply range, and an I/O supply identified as VIO. The device also offers Standby, Sleep, and Listen Only operating features, allowing designers to select power-state behavior according to vehicle-network activity. NXP describes the TJA1443 family as interoperable with high-speed CAN transceivers and compatible with the physical layer defined by ISO 11898-2:2016 and SAE J2284-1 through J2284-5.

The TJA1443 architecture is intended to replace existing high-speed Classical CAN and CAN FD transceiver designs without changing the hardware or software. Its EN, STB, TXD, RXD, VIO, VCC, CANH, CANL, and ground connections support normal communication, bus signaling, supply control, and low-power states. The HVSON-14 package has 14 terminals and measures approximately 3 mm by 4.5 mm according to distributor package information.

Typical uses include automotive electronic control units, body-control modules, gateway controllers, infotainment systems, comfort equipment, and industrial CAN FD gateways. The 5 Mbit/s capability is relevant to powertrain, chassis, and vehicle-backbone networks where higher bus bandwidth than Classical CAN may be required. The configurable low-power modes also suit mixed-activity vehicle networks in which nodes spend substantial time idle.

For PCB implementation, use the manufacturer land pattern and pin-description table for the 14-terminal HVSON package. Place the transceiver and its required support components close to the CAN connector and controller, and follow the recommended bus-side routing and decoupling guidance in the TJA1443 datasheet. Confirm logic thresholds against the selected VIO voltage before finalizing external pull resistors.

This page consolidates the manufacturer specifications, lifecycle information, qualified comparisons, package details, and practical application guidance needed to evaluate the TJA1443ATK/0Z. It also distinguishes true same-package replacements from functionally similar devices whose package or qualification must be reviewed before a PCB substitution.

חלופות תחליף ישיר עבור TJA1443ATK/0Z — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם TJA1443ATK/0Z (אותו גורם צורה וטביעת רגל) — שונים ב Product Type.

NXP Semiconductors
Product Type: High-speed CAN transceiver

TJR1443ATK/0Z

✅ Drop-In
📦 14-HVSON (3 mm x 4.5 mm)
AEC-Q100 Grade 0 qualification versus the standard TJA1443ATK/0Z profile; core data rate remains 5 Mbit/s and package remains 14-HVSON

📋 חלופה להתייחסות (לא בקטלוג)

TJA1443ATK/S1Z

✅ Drop-In
📦 14-HVSON (3 mm x 4.5 mm)
Different orderable suffix with a 0% data-rate difference and the same 14-HVSON footprint; temperature and qualification details require suffix-specific verification

📋 חלופה להתייחסות (לא בקטלוג)

TJR1443ATK/S1Z

✅ Drop-In
📦 14-HVSON (3 mm x 4.5 mm)
Grade 0 TJR qualification and /S1Z ordering suffix versus the standard /0Z variant; data-rate and package differences are 0%

📋 חלופה להתייחסות (לא בקטלוג)

TJA1443ATK/0Z מפרטים

Product Type High-speed CAN and CAN FD transceiver
Maximum CAN Data Rate 5 Mbit/s
Core Supply Voltage Range 4.5 V to 5.5 V
I/O Supply VIO
Supported Protocol Classical CAN and CAN FD
Power-State Features Standby, Sleep, and Listen Only modes
Bus Interface Two-wire CAN bus
CAN Physical-Layer Standard ISO 11898-2:2016
Automotive Network Standards SAE J2284-1 to SAE J2284-5
Control Inputs ENABLE and STB
Error Signal ERR
מארז 14-terminal HVSON, approximately 3 mm x 4.5 mm
Terminal Count 14 terminals
סוג הרכבה Surface mount
סטטוס מחזור חיים Active
Manufacturer NXP Semiconductors

מדריך תצורת פינים של TJA1443ATK/0Z 14-terminal hvson, approximately 3 mm x 4.5 mm

תצורת פינים עבור TJA1443ATK/0Z (מארזת 14-terminal hvson, approximately 3 mm x 4.5 mm). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.

תרשים פינים של מארזת 14-terminal hvson, approximately 3 mm x 4.5 mm עבור TJA1443ATK/0Z

אין נתוני פריסת פינים מפורטים עבור TJA1443ATK/0Z.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

TJA1443ATK/0Z מתאים עבור 6 יישוםs: Automotive CAN FD Gateway, Body Control Module, Powertrain and Chassis Network Interface, Industrial CAN FD Gateway, Vehicle Infotainment Backbone, CAN Bus Monitoring and Diagnostics.

🚗

Automotive CAN FD Gateway

The TJA1443ATK/0Z fits an automotive gateway that connects CAN FD segments with a higher-level vehicle controller. Its 5 Mbit/s capability accommodates high-speed CAN FD signaling, while the 4.5 V to 5.5 V core supply and separate VIO connection support integration with compatible logic levels. Standby, Sleep, and Listen Only modes let the gateway reduce bus activity when traffic is low. Place the transceiver near the protected connector interface and follow the NXP bus-routing and decoupling recommendations to preserve signal quality.

🚗

Body Control Module

A body control module can use the TJA1443ATK/0Z to connect door, lighting, climate, and seating modules over a two-wire CAN network. The 5 Mbit/s maximum rate provides ample bandwidth for ordinary body-control traffic, while CAN FD support allows compatible nodes to use higher-rate data transfer. The device's Listen Only, Standby, and Sleep features help manage current use in modules that remain connected while the vehicle is parked. The 14-terminal HVSON format supports compact board layouts without changing established CAN physical-layer behavior.

⚙️

Powertrain and Chassis Network Interface

The TJA1443ATK/0Z is appropriate for powertrain or chassis controller interfaces that require high-speed, reliable CAN physical-layer signaling. Its listed maximum data rate of 5 Mbit/s addresses CAN FD-capable network segments, and the EN and STB controls give the host controller explicit operating-state management. ISO 11898-2:2016 physical-layer compatibility and the listed SAE J2284 network support provide useful design references. Engineers should still validate termination, bus topology, transient protection, and fault behavior for the final vehicle network.

🏭

Industrial CAN FD Gateway

An industrial CAN FD gateway can use the TJA1443ATK/0Z as the physical interface between a CAN controller and external bus wiring. The 4.5 V to 5.5 V core range suits conventional industrial electronics, and VIO provides flexibility when the controller uses a different interface voltage. Standby and Sleep modes reduce consumption during inactive periods, while Listen Only supports monitoring without transmitting. Use controlled impedance routing, proper bus termination, and surge protection appropriate to the installation environment.

📺

Vehicle Infotainment Backbone

The TJA1443ATK/0Z can serve as a CAN physical-layer interface within vehicle infotainment and comfort-network controllers. A 5 Mbit/s rate supports CAN FD traffic, while the selectable Standby, Sleep, and Listen Only states allow the module to participate in a mixed-activity network without continuously driving the bus. The compact 14-terminal HVSON package is useful where connector routing limits board area. Confirm the module's logic voltage against VIO and place the transceiver where CANH and CANL can reach protected, properly terminated bus circuitry.

🔧

CAN Bus Monitoring and Diagnostics

The TJA1443ATK/0Z is suitable for diagnostics equipment that must observe CAN traffic without interfering with active nodes. Its Listen Only mode supports passive monitoring, while Standby and Sleep modes provide additional control over operating state. The 5 Mbit/s capability covers high-speed CAN FD traffic, and the two-wire physical interface connects directly to the bus through application-appropriate protection and termination. Validate the transceiver mode pins with the host controller during startup to avoid unintended dominant-state transmission.

סיכום מוצרים מומלצים

TJA1043 Existing NXP high-speed CAN transceiver identified as a compatible design reference בשימוש ב-: Automotive CAN FD Gateway, Body Control Module, Powertrain and Chassis Network Interface, Industrial CAN FD Gateway, Vehicle Infotainment Backbone, CAN Bus Monitoring and Diagnostics TJA1043T NXP Semiconductors בשימוש ב-: Automotive CAN FD Gateway, Body Control Module, Powertrain and Chassis Network Interface, Industrial CAN FD Gateway, Vehicle Infotainment Backbone, CAN Bus Monitoring and Diagnostics
What is the TJA1443ATK/0Z?
The TJA1443ATK/0Z is an NXP high-speed CAN transceiver for Classical CAN and CAN FD communication. It interfaces a CAN controller with a two-wire physical bus and supports data rates up to 5 Mbit/s. According to the NXP TJA1443 datasheet, the device implements the CAN physical layer defined in ISO 11898-2:2016 and is suitable for retrofitting compatible high-speed CAN transceiver designs without changing the hardware or software.
What is the operating voltage of TJA1443ATK/0Z?
The TJA1443ATK/0Z operates from a 4.5 V to 5.5 V core supply, while its VIO connection supports the interface voltage required by the connected CAN controller. The NXP product information identifies the CAN FD transceiver and 4.5 V to 5.5 V operating range. Because VIO and VCC are distinct functional rails, confirm both voltage levels in the manufacturer pin table before selecting pull-up and pull-down resistor values.
What is the maximum data rate of TJA1443ATK/0Z?
The TJA1443ATK/0Z supports CAN signaling up to 5 Mbit/s. The DigiKey listing identifies it as a CAN transceiver with an operating rate up to 5 Mbit/s, while the NXP datasheet describes the TJA1443 as a high-speed Classical CAN and CAN FD physical-layer device. Actual application throughput also depends on controller timing, bus length, termination, node count, and signal integrity.
Where can I download the TJA1443ATK/0Z datasheet PDF?
The official TJA1443 datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1443.pdf. It contains the general description, supply information, operating modes, electrical characteristics, pin descriptions, application information, and package drawing for the TJA1443 family. Use the NXP document to confirm every HVSON-14 connection and the required external components for the selected board revision.
Where can I find the TJA1443ATK/0Z pinout?
The TJA1443ATK/0Z uses a 14-terminal HVSON package with 14 terminals, and its complete pin descriptions are listed in the NXP TJA1443 datasheet. Distributor package information identifies the body as approximately 3 mm by 4.5 mm. Use the manufacturer pin-description table and land-pattern drawing when assigning CANH, CANL, VCC, VIO, GND, EN, STB, TXD, RXD, and remaining package connections.
What is the TJA1443ATK/0Z package?
The TJA1443ATK/0Z is packaged in a 14-terminal HVSON surface-mount package, approximately 3 mm by 4.5 mm according to distributor information. Search suggestions for this part also refer to a DFN14-style package designation. For PCB manufacturing, use the exact NXP package drawing and recommended land pattern rather than treating all 14-terminal CAN transceivers as footprint-compatible.
What power modes does the TJA1443ATK/0Z support?
The TJA1443ATK/0Z supports Standby, Sleep, and Listen Only modes in addition to normal high-speed CAN operation. The NXP product overview explicitly identifies these low-power features. EN and STB provide control over the available operating states, allowing an automotive or industrial controller to reduce bus activity when the network is not being used while retaining a path for wake-up or monitoring behavior.
Where to buy TJA1443ATK/0Z online?
Use the Request a Quote form on this page to request current availability, order quantities, and lead time for TJA1443ATK/0Z. The form provides a direct purchasing route without relying on static market listings that may change rapidly. NXP lists the underlying TJA1443ATK family as active, while the exact orderable suffix and delivery schedule should be confirmed during quotation.
What is the price of TJA1443ATK/0Z?
Submit the Request a Quote form on this page for the current TJA1443ATK/0Z price and volume breaks. Commercial pricing for this CAN transceiver can vary with order quantity, package suffix, delivery date, and supply conditions, so a static unit figure should not be used for budgeting. The quote request also allows you to state target quantities, reel requirements, and expected production dates.
What is the lead time and stock status for TJA1443ATK/0Z?
Request current stock, minimum order quantity, and lead time through the Request a Quote form on this page. NXP identifies the TJA1443ATK product family as active, but that lifecycle statement does not establish the stock level of every suffix or package option. Include your required quantity and delivery schedule so the quotation can reflect the appropriate manufacturing and logistics plan.
What is the best drop-in replacement for TJA1443ATK/0Z?
The closest documented drop-in candidates are TJR1443ATK/0Z, TJA1443ATK/S1Z, and TJR1443ATK/S1Z because they retain the 14-terminal HVSON format and belong to the same NXP TJA144x transceiver family. Cross-reference information identifies TJA1443ATK/S1Z and TJR1443ATK/0Z as parametric equivalents. Verify suffix-specific temperature grade, qualification, ordering code, and exposed-pad requirements before replacing the fitted component.
Can TJR1443ATK/0Z replace TJA1443ATK/0Z?
TJR1443ATK/0Z is the closest documented same-package replacement for TJA1443ATK/0Z and appears in the cross-reference results as a parametrically equivalent NXP CAN transceiver. Both use the 14-terminal HVSON format and provide Standby, Sleep, and Listen Only operation. The TJR device is identified as AEC-Q100 Grade 0, so it may provide a different qualification profile; confirm temperature grade and all orderable suffix details before production use.
What is the best TI equivalent for TJA1443ATK/0Z?
The Texas Instruments TCAN1043A is described in NXP-related replacement discussions as pin-to-pin compatible with the TJA1043 and TJA1443 functional family, but it is not established as a same-package drop-in for the 14-terminal HVSON TJA1443ATK/0Z. Treat it as a functional cross-reference rather than a solder-compatible substitute. Confirm footprint dimensions, exposed-pad connection, logic levels, supply pins, and transceiver mode behavior before considering a PCB revision.
When should I choose TJA1443ATK/0Z over TJR1443ATK/0Z?
Choose TJA1443ATK/0Z when the design requires the standard NXP TJA1443ATK variant and does not specifically require the TJR automotive Grade 0 qualification profile. Choose TJR1443ATK/0Z when its documented Grade 0 qualification matches the vehicle program. Both retain the 14-terminal HVSON footprint and closely related low-power features, so lifecycle, qualification, and suffix-specific ordering requirements should determine the final choice.
Is TJA1443ATK/0Z suitable for CAN FD gateways?
The TJA1443ATK/0Z is suitable for CAN FD gateway implementations requiring a high-speed physical-layer interface up to 5 Mbit/s. Its 4.5 V to 5.5 V core-supply range, VIO interface, and configurable Standby, Sleep, and Listen Only modes support controller-to-bus communication and power management. The NXP datasheet confirms compatibility with high-speed CAN FD transceiver applications, subject to bus timing, termination, and signal-integrity requirements.
What are the key specifications of TJA1443ATK/0Z that engineers should know?
The key TJA1443ATK/0Z specifications are a 5 Mbit/s maximum CAN data rate, 4.5 V to 5.5 V core-supply operation, VIO support, and a 14-terminal HVSON package. The device supports Classical CAN, CAN FD, Standby, Sleep, and Listen Only modes. The NXP datasheet also identifies ISO 11898-2:2016 physical-layer compliance and SAE J2284-1 through J2284-5 network compatibility. Package, thermal, and pin details must be checked against the manufacturer document.

נתוני עזר הנדסיים עבור TJA1443ATK/0Z — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose TJA1443ATK/0Z when the design requires the standard NXP TJA1443ATK orderable variant, a 5 Mbit/s CAN FD interface, and a 14-terminal HVSON footprint. Select TJR1443ATK/0Z when its documented AEC-Q100 Grade 0 qualification is required by an automotive program; its principal data rate and package remain the same. Use TJA1443ATK/S1Z when that suffix is the approved procurement configuration for the design. TJR1443ATK/S1Z combines the TJR Grade 0 profile with the /S1Z ordering option. For every alternative, verify the complete manufacturer ordering code, temperature range, exposed-pad layout, logic thresholds, and qualification documents before production substitution.

השוואה עם חלופות

פרמטר מוצר זה TJR1443ATK/0Z TJA1443ATK/S1Z TJR1443ATK/S1Z
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 14-HVSON (3 mm x 4.5 mm) 14-HVSON (3 mm x 4.5 mm) 14-HVSON (3 mm x 4.5 mm) 14-HVSON (3 mm x 4.5 mm)
Product Type High-speed CAN and CAN FD transceiver High-speed CAN and CAN FD transceiver High-speed CAN and CAN FD transceiver High-speed CAN and CAN FD transceiver
Maximum Data Rate 5 Mbit/s 5 Mbit/s 5 Mbit/s 5 Mbit/s
Core Supply Voltage 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V
Operating Modes Standby, Sleep, and Listen Only Standby, Sleep, and Listen Only Standby, Sleep, and Listen Only Standby, Sleep, and Listen Only
CAN Physical-Layer Support ISO 11898-2:2016 ISO 11898-2:2016 family support ISO 11898-2:2016 family support ISO 11898-2:2016 family support
Control Functions VIO, ENABLE, STB, and ERR VIO, ENABLE, STB, and ERR family functions VIO, ENABLE, STB, and ERR family functions VIO, ENABLE, STB, and ERR family functions
Low-Power Operation Sleep mode Sleep mode Sleep mode Sleep mode

מבדילים עיקריים

  • Same-package Grade 0 qualification option (לעומתTJR1443ATK/0Z)
  • Direct 14-HVSON family substitution (לעומתTJA1443ATK/S1Z)
  • Automotive Grade 0 with /S1Z ordering option (לעומתTJR1443ATK/S1Z)

הערות תכנון

Use the NXP TJA1443 land pattern for the 14-terminal HVSON package and place the transceiver close to the CAN connector or protection network. Keep CANH and CANL traces short, matched, and away from switching nodes and noisy digital clocks. Route the pair as a differential pair according to the application guidance in the datasheet, and verify the exposed-pad connection on the selected land pattern.

Decouple VCC locally with the capacitance and ESR characteristics recommended in the NXP datasheet, and treat VIO as a separate interface supply rather than assuming it can be tied directly to VCC. Check controller TXD and RXD logic thresholds against the selected VIO voltage before setting external pull resistors. This prevents bus contention, excessive supply current, and unreliable wake-up behavior.

Do not substitute a CAN transceiver solely because its data rate is above 5 Mbit/s. A valid replacement must also match the HVSON footprint, pin functions, VCC and VIO requirements, exposed-pad arrangement, low-power modes, and qualification profile. Validate TXD behavior during reset and wake-up so the node cannot unintentionally drive the dominant state while the controller is uninitialized.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The manufacturer documentation identifies ISO 11898-2:2016 and SAE J2284-1 through J2284-5. TJR1443ATK/0Z is identified as AEC-Q100 Grade 0, but the qualification status of the standard TJA1443ATK/0Z suffix was not established. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for each exact orderable suffix.

הנתונים אומתו בתאריך: 2026-11-09 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

tja1443atk datasheet tja1443atk datasheet mouser tja1443atk dfn14 TJA1443ATK/0Z datasheet pdf TJA1443ATK/0Z pinout TJA1443ATK/0Z footprint TJA1443ATK/0Z CAN FD TJA1443ATK/0Z 5Mbit/s TJA1443ATK/0Z equivalent TJA1443ATK/0Z replacement TJA1443ATK/0Z price TJA1443ATK/0Z stock

רכיבים ומונחים קשורים

NXP Semiconductors TJA1443ATK/0Z TJR1443ATK/0Z TJA1443ATK/S1Z TJR1443ATK/S1Z TJA1443 TJA1043 TJA1043T CAN transceiver CAN FD Classical CAN physical-layer interface network interface IC two-wire CAN bus ISO 11898-2:2016 SAE J2284-1 SAE J2284-5 VIO ENABLE STB ERR 5 Mbit/s 14-HVSON DFN14 Standby mode Sleep mode Listen Only mode surface-mount semiconductor RoHS REACH AEC-Q100
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר