TJA1443ATK/0Z - 5Mbit/s CAN FD Transceiver | NXP
MPN: TJA1443ATK/0Z ✓ AktifTJA1443ATK/0Z Ringkasan
A high-speed CAN transceiver is an interface integrated circuit that converts logic-level controller signals into the dominant and recessive voltage states used on a CAN bus. The TJA1443 belongs to the broader network-interface hierarchy: CAN transceiver, physical-layer interface, interface IC, and semiconductor. Its implementation supports high-speed Classical CAN and CAN FD systems while simplifying conversion between a digital CAN controller and the bus wiring.
The principal operating features include a maximum listed signaling rate of 5 Mbit/s, a 4.5 V to 5.5 V core-supply range, and an I/O supply identified as VIO. The device also offers Standby, Sleep, and Listen Only operating features, allowing designers to select power-state behavior according to vehicle-network activity. NXP describes the TJA1443 family as interoperable with high-speed CAN transceivers and compatible with the physical layer defined by ISO 11898-2:2016 and SAE J2284-1 through J2284-5.
The TJA1443 architecture is intended to replace existing high-speed Classical CAN and CAN FD transceiver designs without changing the hardware or software. Its EN, STB, TXD, RXD, VIO, VCC, CANH, CANL, and ground connections support normal communication, bus signaling, supply control, and low-power states. The HVSON-14 package has 14 terminals and measures approximately 3 mm by 4.5 mm according to distributor package information.
Typical uses include automotive electronic control units, body-control modules, gateway controllers, infotainment systems, comfort equipment, and industrial CAN FD gateways. The 5 Mbit/s capability is relevant to powertrain, chassis, and vehicle-backbone networks where higher bus bandwidth than Classical CAN may be required. The configurable low-power modes also suit mixed-activity vehicle networks in which nodes spend substantial time idle.
For PCB implementation, use the manufacturer land pattern and pin-description table for the 14-terminal HVSON package. Place the transceiver and its required support components close to the CAN connector and controller, and follow the recommended bus-side routing and decoupling guidance in the TJA1443 datasheet. Confirm logic thresholds against the selected VIO voltage before finalizing external pull resistors.
This page consolidates the manufacturer specifications, lifecycle information, qualified comparisons, package details, and practical application guidance needed to evaluate the TJA1443ATK/0Z. It also distinguishes true same-package replacements from functionally similar devices whose package or qualification must be reviewed before a PCB substitution.
Pilihan pengganti yang segera untuk TJA1443ATK/0Z — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera TJA1443ATK/0Z (sama faktor bentuk dan kaki) — berbeza dalam Product Type.
TJR1443ATK/0Z
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TJA1443ATK/S1Z
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TJR1443ATK/S1Z
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TJA1443ATK/0Z Spesifikasi
| Product Type | High-speed CAN and CAN FD transceiver |
| Maximum CAN Data Rate | 5 Mbit/s |
| Core Supply Voltage Range | 4.5 V to 5.5 V |
| I/O Supply | VIO |
| Supported Protocol | Classical CAN and CAN FD |
| Power-State Features | Standby, Sleep, and Listen Only modes |
| Bus Interface | Two-wire CAN bus |
| CAN Physical-Layer Standard | ISO 11898-2:2016 |
| Automotive Network Standards | SAE J2284-1 to SAE J2284-5 |
| Control Inputs | ENABLE and STB |
| Error Signal | ERR |
| Kemasan | 14-terminal HVSON, approximately 3 mm x 4.5 mm |
| Terminal Count | 14 terminals |
| Jenis Pemasangan | Surface mount |
| Status Lingkungan Hidup | Active |
| Manufacturer | NXP Semiconductors |
Panduan Konfigurasi Pin TJA1443ATK/0Z 14-terminal hvson, approximately 3 mm x 4.5 mm
Konfigurasi pin untuk TJA1443ATK/0Z (14-terminal hvson, approximately 3 mm x 4.5 mm pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk TJA1443ATK/0Z.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
TJA1443ATK/0Z patut untuk 6 aplikasis: Automotive CAN FD Gateway, Body Control Module, Powertrain and Chassis Network Interface, Industrial CAN FD Gateway, Vehicle Infotainment Backbone, CAN Bus Monitoring and Diagnostics.
Automotive CAN FD Gateway
The TJA1443ATK/0Z fits an automotive gateway that connects CAN FD segments with a higher-level vehicle controller. Its 5 Mbit/s capability accommodates high-speed CAN FD signaling, while the 4.5 V to 5.5 V core supply and separate VIO connection support integration with compatible logic levels. Standby, Sleep, and Listen Only modes let the gateway reduce bus activity when traffic is low. Place the transceiver near the protected connector interface and follow the NXP bus-routing and decoupling recommendations to preserve signal quality.
Disebarkan
Body Control Module
A body control module can use the TJA1443ATK/0Z to connect door, lighting, climate, and seating modules over a two-wire CAN network. The 5 Mbit/s maximum rate provides ample bandwidth for ordinary body-control traffic, while CAN FD support allows compatible nodes to use higher-rate data transfer. The device's Listen Only, Standby, and Sleep features help manage current use in modules that remain connected while the vehicle is parked. The 14-terminal HVSON format supports compact board layouts without changing established CAN physical-layer behavior.
Disebarkan
Powertrain and Chassis Network Interface
The TJA1443ATK/0Z is appropriate for powertrain or chassis controller interfaces that require high-speed, reliable CAN physical-layer signaling. Its listed maximum data rate of 5 Mbit/s addresses CAN FD-capable network segments, and the EN and STB controls give the host controller explicit operating-state management. ISO 11898-2:2016 physical-layer compatibility and the listed SAE J2284 network support provide useful design references. Engineers should still validate termination, bus topology, transient protection, and fault behavior for the final vehicle network.
Disebarkan
Industrial CAN FD Gateway
An industrial CAN FD gateway can use the TJA1443ATK/0Z as the physical interface between a CAN controller and external bus wiring. The 4.5 V to 5.5 V core range suits conventional industrial electronics, and VIO provides flexibility when the controller uses a different interface voltage. Standby and Sleep modes reduce consumption during inactive periods, while Listen Only supports monitoring without transmitting. Use controlled impedance routing, proper bus termination, and surge protection appropriate to the installation environment.
Disebarkan
Vehicle Infotainment Backbone
The TJA1443ATK/0Z can serve as a CAN physical-layer interface within vehicle infotainment and comfort-network controllers. A 5 Mbit/s rate supports CAN FD traffic, while the selectable Standby, Sleep, and Listen Only states allow the module to participate in a mixed-activity network without continuously driving the bus. The compact 14-terminal HVSON package is useful where connector routing limits board area. Confirm the module's logic voltage against VIO and place the transceiver where CANH and CANL can reach protected, properly terminated bus circuitry.
Disebarkan
CAN Bus Monitoring and Diagnostics
The TJA1443ATK/0Z is suitable for diagnostics equipment that must observe CAN traffic without interfering with active nodes. Its Listen Only mode supports passive monitoring, while Standby and Sleep modes provide additional control over operating state. The 5 Mbit/s capability covers high-speed CAN FD traffic, and the two-wire physical interface connects directly to the bus through application-appropriate protection and termination. Validate the transceiver mode pins with the host controller during startup to avoid unintended dominant-state transmission.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk TJA1443ATK/0Z — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | TJR1443ATK/0Z | TJA1443ATK/S1Z | TJR1443ATK/S1Z |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 14-HVSON (3 mm x 4.5 mm) | 14-HVSON (3 mm x 4.5 mm) | 14-HVSON (3 mm x 4.5 mm) | 14-HVSON (3 mm x 4.5 mm) |
| Product Type | High-speed CAN and CAN FD transceiver | High-speed CAN and CAN FD transceiver | High-speed CAN and CAN FD transceiver | High-speed CAN and CAN FD transceiver |
| Maximum Data Rate | 5 Mbit/s | 5 Mbit/s | 5 Mbit/s | 5 Mbit/s |
| Core Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Operating Modes | Standby, Sleep, and Listen Only | Standby, Sleep, and Listen Only | Standby, Sleep, and Listen Only | Standby, Sleep, and Listen Only |
| CAN Physical-Layer Support | ISO 11898-2:2016 | ISO 11898-2:2016 family support | ISO 11898-2:2016 family support | ISO 11898-2:2016 family support |
| Control Functions | VIO, ENABLE, STB, and ERR | VIO, ENABLE, STB, and ERR family functions | VIO, ENABLE, STB, and ERR family functions | VIO, ENABLE, STB, and ERR family functions |
| Low-Power Operation | Sleep mode | Sleep mode | Sleep mode | Sleep mode |
Penyeberangsung Jelas
- Same-package Grade 0 qualification option (vsTJR1443ATK/0Z)
- Direct 14-HVSON family substitution (vsTJA1443ATK/S1Z)
- Automotive Grade 0 with /S1Z ordering option (vsTJR1443ATK/S1Z)
Catatan Desain
Use the NXP TJA1443 land pattern for the 14-terminal HVSON package and place the transceiver close to the CAN connector or protection network. Keep CANH and CANL traces short, matched, and away from switching nodes and noisy digital clocks. Route the pair as a differential pair according to the application guidance in the datasheet, and verify the exposed-pad connection on the selected land pattern.
Decouple VCC locally with the capacitance and ESR characteristics recommended in the NXP datasheet, and treat VIO as a separate interface supply rather than assuming it can be tied directly to VCC. Check controller TXD and RXD logic thresholds against the selected VIO voltage before setting external pull resistors. This prevents bus contention, excessive supply current, and unreliable wake-up behavior.
Do not substitute a CAN transceiver solely because its data rate is above 5 Mbit/s. A valid replacement must also match the HVSON footprint, pin functions, VCC and VIO requirements, exposed-pad arrangement, low-power modes, and qualification profile. Validate TXD behavior during reset and wake-up so the node cannot unintentionally drive the dominant state while the controller is uninitialized.
Maklumat Kesediaan
The manufacturer documentation identifies ISO 11898-2:2016 and SAE J2284-1 through J2284-5. TJR1443ATK/0Z is identified as AEC-Q100 Grade 0, but the qualification status of the standard TJA1443ATK/0Z suffix was not established. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for each exact orderable suffix.