TLV2252IP - Dual Rail-to-Rail Low-Power Op Amp | Texas Instruments
MPN: TLV2252IP ✓ פעילTLV2252IP סקירה
An operational amplifier is an analog signal-conditioning semiconductor that amplifies the voltage difference between its non-inverting and inverting inputs. The TLV2252 belongs to the operational-amplifier, analog-IC, and signal-conditioning hierarchy. It is designed for low-voltage circuits where low supply current, low input bias current, and output operation close to the supply rails are useful.
The TLV2252 family's key features include output swing that includes both supply rails, low noise, and very low input bias current. According to the TLV2252 product documentation, the 19 nV/√Hz typical input noise density at 1 kHz is suitable for low-level analog signal conditioning. The 1 pA typical input bias current is especially relevant to sensors and transducers whose output impedance is high.
The TLV2252IP combines two amplifiers in one PDIP package, allowing a differential or noninverting amplifier, an instrumentation-style signal chain, or two independent analog channels. Its low-power operating current supports battery-powered and portable equipment, while the -40°C to +125°C temperature range allows use in industrial and automotive-temperature environments when the complete system meets its applicable qualification requirements.
Typical uses include sensor-interface amplification, low-frequency filter stages, portable instrumentation, audio input conditioning, and general-purpose analog signal processing. Two independent channels can also implement differential gain, active filtering, or gain stages where board area is constrained. The rail-to-rail output can improve dynamic range in low-voltage systems by allowing the output to approach the supply limits more closely than a conventional non-rail-to-rail amplifier.
When laying out a board, use the manufacturer pin-description table to assign inputs, outputs, and supply pins, and place the decoupling capacitor close to the positive and negative supply terminals. Verify the required output swing against the load and input common-mode range before selecting resistor values or relying on full-scale operation. Stable operation with capacitive loads should be confirmed using the guidance in the manufacturer datasheet.
This product record combines manufacturer ordering information, temperature and package details, low-noise and low-bias-current characteristics, practical application guidance, and a package-conscious comparison with potential replacements. These engineering details help distinguish a true pin-compatible substitution from a merely similar low-power operational amplifier.
חלופות תחליף ישיר עבור TLV2252IP — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
TLV2252AIP
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TLV2452IP
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TLV2452AIP
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TLV2462AIP
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TLC2252AIP
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TLV2252IP דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Dual operational amplifier |
| Number of Channels | 2 channels |
| Output Topology | Rail-to-rail output |
| Supply Class | Low-voltage, low-power |
| Supply Current per Channel | 34 µA typical |
| Input Bias Current | 1 pA typical |
| Input Voltage Noise Density | 19 nV/√Hz typical at 1 kHz |
| טווח טמפרטורת פעולה | -40°C to +125°C |
| מארז | PDIP (P), 8 pins |
| סוג הרכבה | Through-hole |
מדריך תצורת פינים של TLV2252IP pdip (p), 8 pins
תצורת פינים עבור TLV2252IP (מארזת pdip (p), 8 pins). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור TLV2252IP.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
TLV2252IP מתאים עבור 6 יישוםs: Portable Sensor Signal Conditioning, Industrial Process Measurement, Low-Power Audio Input Stage, Precision Filter and Gain Stage, Battery-Powered Data Acquisition, General-Purpose Analog Interface.
Portable Sensor Signal Conditioning
The TLV2252IP is appropriate for battery-powered sensor interfaces because the dual amplifier consumes 34 µA per channel typically and offers 1 pA typical input bias current. That low bias current limits the error introduced by high-source-impedance sensors, while the 19 nV/√Hz typical input noise density at 1 kHz supports weak-signal conditioning. A practical implementation uses one channel for amplification and the second for filtering or buffering. The rail-to-rail output improves available signal range in low-voltage systems, although the amplifier's input common-mode limits must be respected during startup and sensor transitions.
מומלץ
Industrial Process Measurement
The TLV2252IP can condition low-level industrial process signals when low power and input bias current are more important than high bandwidth. Its 1 pA typical input bias current reduces loading on high-impedance probes, and the 19 nV/√Hz typical noise density at 1 kHz helps preserve small measurement signals. The -40°C to +125°C operating range supports equipment deployed across wide ambient conditions. Place both amplifier channels close to their signal sources or use one for differential gain and one for active filtering. Verify input common-mode behavior, output swing, and capacitive-load stability in the completed analog path.
מומלץ
Low-Power Audio Input Stage
The TLV2252IP can serve as a low-power audio preamplifier or line-stage amplifier where the source impedance is relatively high. The 19 nV/√Hz typical input noise density at 1 kHz and 1 pA typical input bias current are useful for preserving weak audio information, while rail-to-rail output swing can provide greater headroom in single-supply equipment. Gain can be set with conventional feedback resistors, with the second channel available for an output buffer or active filter. The design should account for the amplifier's exact bandwidth, slew rate, output swing, and capacitive-load behavior before targeting the required audio bandwidth.
מומלץ
Precision Filter and Gain Stage
Both channels in the TLV2252IP can implement active filters or cascaded gain sections in compact analog modules. A 34 µA typical supply current per channel helps limit total power when both sections are active, and the low-noise input stage is beneficial when the filter processes signals close to the measurement floor. Use stable resistor and capacitor values and keep the summing node compact to minimize parasitic feedback. Because the available family members differ in bandwidth and slew rate, verify that the selected amplifier remains stable at the intended gain, operating frequency, and capacitive loading of the filter.
מומלץ
Battery-Powered Data Acquisition
The TLV2252IP is suitable for low-power data-acquisition front ends that amplify sensor or transducer outputs before conversion. The dual-channel configuration provides two conditioned outputs from one 8-pin PDIP package, reducing board area, while 34 µA typical current per channel supports longer operating time in portable instruments. Its 1 pA typical input bias current minimizes disturbance of high-impedance sources, and rail-to-rail output helps maximize the range of a low-voltage converter input. The system designer should confirm input common-mode range at startup, output settling, and ADC acquisition timing.
מומלץ
General-Purpose Analog Interface
The TLV2252IP provides a practical dual-amplifier building block for instrumentation, interface boards, and educational or industrial control modules. Rail-to-rail output operation is useful when the signal must span much of a low-voltage supply range, while low supply current supports compact systems with limited thermal budgets. One channel can serve as a noninverting amplifier and the other as a voltage follower, or the channels can form a differential stage. The engineer should use the manufacturer pin configuration and complete electrical limits to establish polarity, gain, common-mode range, and output loading before releasing the PCB design.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור TLV2252IP — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | TLV2252AIP | TLV2452IP | TLV2452AIP | TLV2462AIP | TLC2252AIP |
|---|---|---|---|---|---|---|
| Package | PDIP (P), 8 pins | PDIP (P), 8 pins | PDIP (P), 8 pins | PDIP (P), 8 pins | PDIP (P), 8 pins | PDIP (P), 8 pins |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier |
| Number of Pins | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins |
| Mounting Type | Through-hole PDIP | Through-hole PDIP | Through-hole PDIP | Through-hole PDIP | Through-hole PDIP | Through-hole PDIP |
מבדילים עיקריים
- Low supply-current characteristic within a dual amplifier (לעומתTLV2452IP)
- Very low input bias current for high-impedance sources (לעומתTLC2252AIP)
- Low-noise dual-channel integration in an 8-pin PDIP (לעומתTLV2462AIP)
הערות תכנון
Assign the two channels from the manufacturer pin-configuration diagram and keep each inverting-input feedback loop compact. A long trace around the inverting node adds parasitic capacitance that can affect frequency response and stability. Place the supply bypass capacitor close to the device supply terminals, and route sensitive input traces away from switching nodes and high-current return paths to preserve the benefit of the low 19 nV/√Hz typical input noise density.
Do not assume that rail-to-rail output guarantees the amplifier can process every input voltage. Check the input common-mode range, output-swing limits, and load current across the intended supply range. The TLV2252IP is also fully specified for single-supply and split-supply operation, but startup transients can move a signal outside the normal input range. Use the manufacturer limits to define input and output clamping requirements for the complete circuit.
Estimated: with two channels operating at the typical 34 µA per-channel current and a 3.3 V supply, the amplifier's supply current contribution is approximately 68 µA and its calculated supply power is approximately 0.224 mW. Actual device power also depends on the input common-mode voltage, output stage activity, load, and leakage. Use this calculation for battery-budget estimation, then confirm the operating current under the real signal and load conditions.
מידע על תאימות
The available manufacturer ordering information does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for the PDIP package. AEC-Q100 is not applicable to the standard TLV2252IP ordering code.