TLV2334IN - 525 kHz Quad CMOS Op Amp | Texas Instruments
MPN: TLV2334IN ✓ פעילTLV2334IN סקירה
A CMOS operational amplifier is a voltage-amplifying semiconductor device that uses complementary metal-oxide-semiconductor circuitry to process differential signals. Operational amplifiers form the basic building blocks of analog signal chains, where they perform functions such as buffering, amplification, filtering, level shifting, and active feedback control. A quad package consolidates four amplifiers while sharing common supply and ground connections.
The TLV2334IN combines a 525 kHz gain-bandwidth product with a 0.4 V/µs slew rate, allowing moderate-frequency small-signal amplification without the bandwidth of a high-speed precision amplifier. Its approximately 2.0 µA input bias current is suitable for many battery-powered and high-impedance sensing circuits. The 60 dB CMRR specification supports rejection of common-mode interference when signal levels are small relative to the supply rails.
According to the manufacturer’s LinCMOS documentation, the family is characterized for 3 V and 5 V single-supply operation and supports supply ranges extending to 8 V over the specified temperature range. The common-mode input range extends below the negative supply rail, while the output range includes negative voltage operation. These rail-related characteristics make the device useful in single-supply circuits that process signals centered near ground.
Typical uses include low-frequency sensor conditioning, active audio paths, sample-and-hold circuitry, transducers, and general instrumentation. Four amplifiers in one package reduce board area when a design needs several similar signal-conditioning channels. For applications requiring greater precision or substantially higher bandwidth, the selection should be revisited because the 525 kHz gain-bandwidth product and 60 dB CMRR define a general-purpose rather than precision or high-speed role.
When designing a board around this device, bypass each supply connection with local high-frequency decoupling and route sensitive input and feedback paths away from switching nodes. Because the common-mode and output ranges are rail-dependent, verify the actual signal excursion against the chosen supply voltage before relying on near-rail input or output operation.
This page combines the exact ordering information, electrical characteristics, package details, application guidance, and drop-in replacement assessment for the TLV2334IN. It is intended to help engineers distinguish genuine footprint-compatible options from functionally similar amplifiers that would require board or schematic changes.
חלופות תחליף ישיר עבור TLV2334IN — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
TLV2334INE4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TLV2334IN דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifiers | 4 circuits |
| Technology | LinCMOS |
| Gain-Bandwidth Product | 525 kHz |
| Slew Rate | 0.4 V/µs |
| Common-Mode Rejection Ratio | 60 dB |
| Input Bias Current | 2.0 µA |
| Nominal Supply Voltage | 5 V |
| Fully Characterized Single-Supply Operation | 3 V and 5 V |
| Maximum Stated Supply Range | 8 V |
| טווח טמפרטורת פעולה | -40 °C to +85 °C |
| מארז | 14-pin plastic DIP |
| מספר פינים | 14 pins |
| סוג הרכבה | Through-hole |
| Lead Spacing | 7.62 mm |
| Common-Mode Input Voltage Range | Extends below the negative rail and up to VDD |
| טווח מתח פלט | Includes negative output voltage |
מדריך תצורת פינים של TLV2334IN 14-pin plastic dip
תצורת פינים עבור TLV2334IN (מארזת 14-pin plastic dip). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור TLV2334IN.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
TLV2334IN מתאים עבור 6 יישוםs: Low-Frequency Sensor Conditioning, Portable Audio Input Path, Industrial Control Signal Interface, Active Filter and Oscillator, Data Acquisition Front End, Power Supply Feedback and Monitoring.
Low-Frequency Sensor Conditioning
The TLV2334IN is appropriate for conditioning outputs from moderate-impedance sensors because its approximately 2.0 µA input bias current limits the bias-related voltage error in many sensor interfaces. Four amplifiers can support buffering, gain, active filtering, and output offset stages within one 14-pin plastic DIP. The 525 kHz gain-bandwidth product and 0.4 V/µs slew rate are adequate for low-frequency signals, while 3 V and 5 V single-supply operation simplifies portable instrumentation. Confirm the sensor output range, permissible common-mode voltage, and required noise performance before finalizing the circuit.
מומלץ
Portable Audio Input Path
The TLV2334IN can support low-frequency audio buffering, tone shaping, and active filtering in portable equipment powered from a 3 V or 5 V rail. Its four amplifiers provide separate channels or multiple gain and filtering stages, while the approximately 2.0 µA input bias current is useful with high-impedance audio sources. The 0.4 V/µs slew rate and 525 kHz gain-bandwidth product favor general audio conditioning rather than wideband audio amplification. Validate output swing, capacitive-load stability, and channel-to-channel matching against the intended headphone or line-level interface.
מומלץ
Industrial Control Signal Interface
The TLV2334IN is suitable for low-bandwidth industrial control interfaces that require multiple buffered channels, single-supply operation, and through-hole assembly. A quad amplifier can implement input conditioning, error amplification, active filtering, and output buffering while sharing one 14-pin package. Its 60 dB CMRR helps reject common-mode noise on modest-signal sensor and control paths, while the common-mode range extending below the negative rail supports systems whose signals sit near ground. The design must still account for supply transients, grounding, and the difference between signal bandwidth and the amplifier’s 525 kHz gain-bandwidth product.
מומלץ
Active Filter and Oscillator
The TLV2334IN can implement active low-pass filters, integrators, and quadrature oscillators because four amplifiers are available in one package. Its 0.4 V/µs slew rate and 525 kHz gain-bandwidth product permit operation at frequencies below the amplifier’s small-signal bandwidth, with practical limits determined by component tolerances, output loading, and loop stability. The approximately 2.0 µA input bias current is helpful when high-value timing resistors are used, although it may require bias-current compensation for precision waveforms. Evaluate resistor accuracy and capacitor stability when the oscillator frequency or filter response must remain tightly controlled.
מומלץ
Data Acquisition Front End
The TLV2334IN can form the analog front end of a moderate-speed data-acquisition system by providing channel buffering, gain, and active filtering for sensors or dividers. Its four amplifiers reduce the number of packages needed for four similar conditioning paths, and the 14-pin plastic DIP supports through-hole prototypes and industrial-style assemblies. The 525 kHz gain-bandwidth product gives substantial margin over many slow sensor-bandwidth signals, while 60 dB CMRR improves common-mode rejection. Designers should account for settling behavior, source impedance, ADC input capacitance, and any required conversion-time headroom.
מומלץ
Power Supply Feedback and Monitoring
The TLV2334IN can monitor multiple power rails or amplify error signals in a low-voltage supervisory system. Four amplifiers may implement differential sensing, gain stages, filters, and threshold amplifiers while operating from 3 V or 5 V. The common-mode input capability near or below the negative rail is useful for low-side sensing, although each input must remain within the device’s permitted common-mode range. The approximately 2.0 µA input bias current can create offsets in high-impedance dividers, so resistor values should be selected accordingly, and the 525 kHz gain-bandwidth product should not be confused with a guaranteed transient response.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור TLV2334IN — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | TLV2334INE4 |
|---|---|---|
| Package | 14-PDIP | 14-PDIP |
| Brand | Texas Instruments | Texas Instruments |
| Number of Amplifiers | 4 circuits | 4 circuits |
| Amplifier Type | General-purpose operational amplifier | General-purpose operational amplifier |
| Mounting Type | Through-hole | Through-hole |
| Number of Pins | 14 pins | 14 pins |
מבדילים עיקריים
- Four integrated amplifiers in one through-hole package (לעומתTLV2334INE4)
- Low input bias current for general-purpose signal conditioning (לעומתTLV2334INE4)
- Single-supply operation with near-ground input capability (לעומתTLV2334INE4)
הערות תכנון
Place the primary bypass capacitor directly between the positive supply and ground pins, with its ground return connected to the same quiet ground region. Keep this loop short because package and trace inductance can create supply spikes at the operating amplifier. A larger bulk capacitor near the power entry point can support lower-frequency transients, while the local ceramic capacitor handles higher-frequency demand from the four internal amplifiers.
Route each non-inverting input directly to its source and each inverting feedback path close to the corresponding amplifier pins. Avoid sharing narrow feedback traces between channels because capacitive coupling through the board can create crosstalk. Where the TLV2334IN conditions low-level signals, maintain a continuous ground reference under the DIP and keep switching-regulator traces, inductors, and high-current outputs away from the input and feedback nodes.
Do not assume that the ability to accept input signals below the negative rail permits a dual ±5 V supply. The documented supply range extends to 8 V, with 3 V and 5 V single-supply operation explicitly characterized. Check the absolute-maximum supply rating, input and output excursions, and power-up sequence in the manufacturer datasheet before applying a ±5 V rail or driving an input beyond the linear common-mode region.
Calculate the usable closed-loop bandwidth from the 525 kHz gain-bandwidth product rather than treating that value as a guaranteed flat-bandwidth specification. For a noise-gain setting of 10, the theoretical small-signal bandwidth is approximately 52.5 kHz before noise gain, stability, and loading effects are considered. Check source impedance, feedback resistance, capacitive loading, and output-swing requirements when the signal bandwidth approaches that range.
מידע על תאימות
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for TLV2334IN in the cited product information.