TLV2344ID - Quad 1.7 MHz CMOS Op Amp | Texas Instruments
MPN: TLV2344ID ✓ פעילTLV2344ID סקירה
A CMOS operational amplifier is a voltage-feedback amplifier built with complementary metal-oxide-semiconductor transistors. Its function belongs to the hierarchy of analog amplifier, operational amplifier IC, and signal-conditioning semiconductor. Unlike a general-purpose bipolar amplifier, the TLV2344 family was developed to provide switching-level performance from a low-voltage single supply while approaching the AC performance associated with BiFET operational amplifiers.
The TLV2344ID provides four amplifier channels in one 14-SOIC package. Its typical gain-bandwidth product is 1.7 MHz, making it suitable for audio-frequency signal conditioning, active filtering, sensor amplification, and low-frequency control loops. At a 3 V supply, the device has a typical slew rate of 2.1 V/µs and a typical unity-gain bandwidth of 790 kHz. These figures quantify its speed more directly than generic CMOS classifications and help determine whether a given feedback network can meet bandwidth and settling requirements.
The wide supply range is characterized through 8 V, while 3 V and 5 V single-supply operation are specifically identified. Its common-mode input range extends below the negative rail and to VDD at 25°C, and its output voltage range includes the negative rail. These characteristics are useful in battery-powered systems where signals can approach the lower supply limit and output swing headroom is limited. The four channels can also amplify independent sensors or process multiple stages of a larger analog signal chain.
Typical uses include portable audio amplification, bridge-tied sensor interfaces, active low-pass filters, ADC input conditioning, and general single-supply instrumentation. Designers should verify the exact input and output swing at the selected supply voltage and load, then place input and output components according to the recommended application circuit. A common single-ground bypass capacitor should be placed close to the supply pins, while feedback resistors and compensation networks should remain compact to minimize parasitic effects and preserve bandwidth.
This page combines the TLV2344ID device specifications, package information, sourcing guidance, and application-focused design guidance. It also identifies the limits of drop-in replacement analysis so engineers can distinguish a true pin-compatible substitution from a device that merely has similar headline performance.
חלופות תחליף ישיר עבור TLV2344ID — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
TLV2344Y
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
TLV2344IP
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
TLV2344IDR
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
TLV2344ID דירוגים מרביים ומאפיינים חשמליים
| Amplifier Count | 4 channels |
| Product Type | CMOS operational amplifier |
| Typical Gain-Bandwidth Product | 1.7 MHz |
| Typical Slew Rate at 3 V | 2.1 V/µs |
| Typical Unity-Gain Bandwidth at 3 V | 790 kHz |
| Low-Voltage Supply Operation | 3 V and 5 V single supply |
| Maximum Characterized Supply Voltage | 8 V |
| Common-Mode Input Range | Extends below the negative rail and to VDD at 25°C |
| טווח מתח פלט | Includes the negative rail |
| מארז | 14-SOIC |
| Package Width | 3.90 mm (0.154 in) |
| סוג הרכבה | Surface mount |
| Process Technology | CMOS (LinCMOS) |
| Rail-to-Rail Output | Yes; output range includes the negative rail |
מדריך תצורת פינים של TLV2344ID 3.90 mm (0.154 in)
תצורת פינים עבור TLV2344ID (מארזת 3.90 mm (0.154 in)). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור TLV2344ID.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
TLV2344ID מתאים עבור 6 יישוםs: Portable Sensor Signal Conditioning, Low-Frequency Active Filters, ADC and DAC Interface Conditioning, Audio Preamplification, Industrial Control Signal Conditioning, IoT Edge Signal Conditioning.
Portable Sensor Signal Conditioning
The TLV2344ID suits portable sensor front ends that operate from a 3 V or 5 V rail and require more than one conditioning channel. Its four CMOS amplifiers can amplify, filter, or buffer separate sensor signals while keeping the subsystem compact. The 1.7 MHz typical gain-bandwidth product supports moderate-bandwidth closed-loop designs, and the common-mode input range extending below the negative rail helps process signals centered near ground. Keep sensor returns close to the negative supply where appropriate, and verify the actual sensor output range, noise requirements, and settling time before fixing the gain.
Low-Frequency Active Filters
The four channels in the TLV2344ID can implement cascaded or parallel active-filter stages in portable audio and control systems. A 2.1 V/µs typical slew rate at 3 V and 790 kHz typical unity-gain bandwidth provide useful headroom for moderate-Q low-pass or band-pass networks operating from a single supply. Because the usable closed-loop bandwidth depends on noise gain, calculate each stage's gain and phase margin before finalizing component values. Place resistor and capacitor networks close to the relevant amplifier pins to reduce parasitic feedback and preserve the expected response.
ADC and DAC Interface Conditioning
The TLV2344ID can provide input filtering, level shifting, or gain stages around low- and medium-speed converters operating from 3 V or 5 V. Its common-mode input capability below the negative rail is especially useful when signals are biased around the midpoint of a single supply, while the output range including the negative rail can improve utilization of the converter's signal range. Verify the converter's recommended input and output impedance, then confirm that the amplifier can drive the sampling network and settle to the required accuracy within the available conversion interval.
Audio Preamplification
The TLV2344ID is appropriate for low-level audio preamplification and channel-balancing circuits powered by a single low-voltage rail. Its 1.7 MHz typical gain-bandwidth product and 2.1 V/µs slew rate at 3 V are comfortably above the principal audio band, leaving additional bandwidth for filtering and gain shaping. Common-mode input operation below the negative rail permits source-referenced inputs when biasing is designed correctly. Headroom and distortion checks should use the actual signal amplitude, load impedance, supply voltage, and selected closed-loop gain rather than headline bandwidth alone.
Industrial Control Signal Conditioning
The quad-channel TLV2344ID can condition four related control signals in an industrial controller, including sensor outputs, current-loop interfaces, or actuator feedback. Single-supply operation at 3 V and 5 V fits compact embedded systems, while the 14-SOIC package consolidates four amplifiers into one component. The amplifier's common-mode and output-swing limits must be checked against the protected industrial signal range, and grounding must prevent switching-node currents from entering the analog input paths. Confirm the system's electrical-overload, temperature, and isolation requirements separately from the amplifier's operating characteristics.
IoT Edge Signal Conditioning
The TLV2344ID can condition multiple sensor channels before digital conversion in compact IoT edge devices powered from a battery-derived 3 V rail. Four independent amplifiers reduce the number of analog packages needed when the design handles temperature, pressure, motion, or environmental sensing. Low-voltage single-supply operation simplifies rail planning, and the input range below the negative rail supports appropriately biased sensor signals. A practical design should combine short analog routing, local supply bypassing, input overvoltage protection, and firmware-compatible gain settings without relying on the unused amplifier channels as isolated rails.
נתוני עזר הנדסיים עבור TLV2344ID — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Brand | Texas Instruments |
| Package | 14-SOIC |
| Amplifier Count | 4 channels |
| Typical Gain-Bandwidth Product | 1.7 MHz |
| Typical Slew Rate at 3 V | 2.1 V/µs |
| Typical Unity-Gain Bandwidth at 3 V | 790 kHz |
| Low-Voltage Supply Operation | 3 V and 5 V single supply |
| Maximum Characterized Supply Voltage | 8 V |
| Process Technology | CMOS (LinCMOS) |
הערות תכנון
Place the supply-bypass capacitor as close as practical to the positive and negative supply pins, and keep its ground return short and directly tied to the device ground. Use the capacitor type and value recommended in the manufacturer application circuit. Avoid routing sensitive input and feedback nets beneath or alongside switching-supply traces because capacitive coupling can increase output noise or disturb low-level sensor signals.
Do not interpret the common-mode input range extending below the negative rail as permission to exceed the absolute maximum input voltage. Check every source for operation outside the supply rails, shutdown discharge, and hot-plug conditions. In battery systems, protect inputs against ESD and accidental overvoltage before the signal reaches the amplifier, because internal clamps can conduct and disturb the source when the input exceeds a valid range.
Keep feedback resistors and compensation capacitors compact and connect them directly to the relevant amplifier pins. The usable closed-loop bandwidth depends on noise gain, so a 790 kHz typical unity-gain bandwidth at 3 V does not guarantee the same bandwidth at higher gain. Simulate the complete feedback network with expected load capacitance and PCB parasitics when precise settling time is required.
מידע על תאימות
Compliance attributes are not stated in the cited product information and must be confirmed on the current manufacturer product page or compliance documentation.