TS902IDT - Dual 1.4MHz Rail-to-Rail Op Amp | STMicroelectronics
MPN: TS902IDT ✗ סוף ייצורTS902IDT סקירה
A rail-to-rail operational amplifier is an amplifier whose input common-mode and output voltage ranges can extend close to the positive and negative supply rails. This makes the TS902 useful for low-voltage systems in which the signal can occupy much of the available supply voltage. In the broader device hierarchy, the TS902 is a dual CMOS operational amplifier, placing it within analog and mixed-signal integrated-circuit designs.
The TS902IDT provides a 1.4 MHz gain-bandwidth product for general-purpose amplification at moderate frequencies. Its rail-to-rail input stage supports signal acquisition close to the supply limits, while the rail-to-rail output stage improves output-voltage range. A standby position reduces consumption to 0.5 µA and places the outputs in a high-impedance state, helping conserve power when the amplifier is not actively processing signals.
The TS902IDT is specified for a temperature range of -40 °C to +125 °C. One retrieved technical listing identifies a maximum input offset voltage of 12 mV, while another reports a low bias current of 0.00015 µA. These figures support applications involving sensor interfaces, low-level signal conditioning, and battery-operated instrumentation where offset and input current are important selection criteria.
Typical uses include portable sensor conditioning, industrial measurement, audio preamplification, low-voltage control systems, and current-feedback around transducers. The SOIC-14 package also permits a conventional surface-mount PCB layout with adequate separation between the two amplifier channels.
Designers should account for the 12 mV maximum input offset when the application requires accurate DC measurements. Input and output stability must be evaluated with the selected feedback network and load, while supply bypassing should follow the manufacturer recommendations. The standby function should be driven only with signals that remain compatible with its defined logic levels.
This product page combines package, temperature, frequency, offset, and power information with application-oriented engineering guidance. It also identifies the verified documentation links and explains the limits of the available drop-in replacement cross-reference, helping engineers distinguish a true pin-compatible substitution from a merely similar amplifier.
חלופות תחליף ישיר עבור TS902IDT — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם TS902IDT (אותו גורם צורה וטביעת רגל) — שונים ב Amplifier Type, Operating Temperature Range, Package, Standby Current, Standby Output State.
אין חלופות תואמות Drop-in עבור מוצר זה.
בקשת חלופותTS902IDT דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Dual general-purpose CMOS operational amplifier |
| Number of Amplifiers | 2 channels |
| Gain-Bandwidth Product | 1.4 MHz |
| Input Common-Mode Range | Rail-to-rail |
| טווח מתח פלט | Rail-to-rail |
| Maximum Input Offset Voltage | 12 mV |
| Input Bias Current | 0.00015 µA |
| Standby Current | 0.5 µA |
| Standby Output State | High impedance |
| טווח טמפרטורת פעולה | -40 °C to +125 °C |
| מארז | 14-pin small-outline package (SO14) |
| Delivery Configuration | Tape and reel (DT) |
| סוג הרכבה | Surface mount |
| Technology | CMOS |
| Maximum Supply Voltage | 8 V |
| Power-Supply Operation | Single or dual supply |
| Automotive Temperature Grade | -40 °C to +125 °C |
מדריך תצורת פינים של TS902IDT 14-pin small-outline package (so14)
תצורת פינים עבור TS902IDT (מארזת 14-pin small-outline package (so14)). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור TS902IDT.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
TS902IDT מתאים עבור 6 יישוםs: Low-Power Sensor Signal Conditioning, Portable Measurement Instrumentation, Audio Preamplification, Industrial Control and Actuator Interfaces, Battery-Powered IoT Sensing, Battery Charging and Power Monitoring.
Low-Power Sensor Signal Conditioning
The TS902IDT suits battery-operated sensing systems in which the sensor output can occupy much of the available supply range. Its rail-to-rail input range reduces the need for midrail biasing, while the 1.4 MHz gain-bandwidth product is more than adequate for slow temperature, pressure, and position signals. The reported 0.00015 µA input bias current limits loading on high-impedance sources, and the 0.5 µA standby current supports periodic measurement cycles. Use the amplifier in a non-inverting or differential conditioning stage, and verify that the sensor’s output range remains compatible with the device’s common-mode and supply limits.
מומלץ
Portable Measurement Instrumentation
Portable meters and field-measurement products can use the TS902IDT to amplify low-level sensor signals without a midrail virtual ground. The rail-to-rail output makes the amplifier useful with single-supply analog-to-digital converters whose useful input span approaches the supply rail. Its 1.4 MHz gain-bandwidth product supports moderate-bandwidth filtering and gain stages, while the industrial temperature range of -40 °C to +125 °C supports wider ambient environments. Confirm the selected ADC’s input range, configure gain carefully because the maximum input offset is 12 mV, and account for the amplifier’s output swing when designing the final reference and gain network.
מומלץ
Audio Preamplification
The TS902IDT can serve as a general-purpose dual preamplifier in small audio modules, microphone interfaces, and active transducers. Two amplifiers in one 14-pin package can handle left and right channels or two stages of a signal path, reducing board area compared with separate single amplifiers. Rail-to-rail input and output operation improves signal utilization in low-voltage systems, and the 1.4 MHz gain-bandwidth product is suitable for the wide audio-band signals common to consumer audio. The device is not characterized here as a low-noise audio-grade part, so microphone noise, distortion, input impedance, and channel matching must be evaluated before using it in a precision audio path.
מומלץ
Industrial Control and Actuator Interfaces
The TS902IDT is useful for buffering sensor and control signals in industrial equipment where single-supply operation simplifies power distribution. Rail-to-rail input capability permits direct connection to sensors biased near either supply rail, while the rail-to-rail output can drive a following converter or analog control stage. The -40 °C to +125 °C temperature range is appropriate for many industrial environments, but the maximum offset of 12 mV must be included in control-loop error analysis. Keep feedback traces short, provide local supply bypassing, and verify output loading because general-purpose rail-to-rail amplifiers can exhibit reduced drive or increased distortion near the output rails.
מומלץ
Battery-Powered IoT Sensing
The TS902IDT can condition outputs from low-energy IoT sensors while remaining compatible with compact single-supply systems. Its rail-to-rail input range avoids wasting signal span, and the standby mode reduces consumption to 0.5 µA when measurements are paused. The 1.4 MHz bandwidth is more than sufficient for many environmental and occupancy sensors, while dual-channel packaging allows two sensor inputs to share one IC. A practical design should include a defined shutdown level, ensure the sensor cannot back-power the output during standby, and confirm that leakage from surrounding circuitry does not dominate the 0.5 µA supply current.
מומלץ
Battery Charging and Power Monitoring
The TS902IDT can amplify the voltage and current signals used to monitor a battery-powered subsystem. Rail-to-rail operation allows sensing near the low end of a single-supply rail, and the dual-channel architecture can compare a battery signal with a reference or amplify two related measurements. The amplifier’s standby current of 0.5 µA is useful when the monitor is sampled infrequently, although the surrounding divider, switches, and protection components can consume more current than the amplifier itself. Use low-leakage input components, account for the 12 mV maximum offset in calibration, and verify the common-mode limits before the battery voltage can fall below the measurement range.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור TS902IDT — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Brand | STMicroelectronics |
| Package | 14-pin small-outline package (SO14) |
| Amplifier Configuration | Dual |
| Gain-Bandwidth Product | 1.4 MHz |
| Input Common-Mode Range | Rail-to-rail |
| Output Voltage Range | Rail-to-rail |
| Maximum Input Offset Voltage | 12 mV |
| Input Bias Current | 0.00015 µA |
| Standby Current | 0.5 µA |
| Operating Temperature Range | -40 °C to +125 °C |
מבדילים עיקריים
- Combines rail-to-rail operation with a dedicated low-power state (לעומתLM2902DT)
- Provides two independently usable amplifier channels in one package (לעומתLM2902DT)
- Supports an extended industrial temperature range (לעומתTS904IDT)
הערות תכנון
Do not treat SOIC-14 package equality as proof of replacement compatibility. A substitute must match the TS902IDT pin functions, including the standby-control behavior, and must satisfy the rail-to-rail input range, output swing, supply-voltage limits, and output-current requirements. Pay particular attention to the 12 mV maximum input offset and to changes in bias current, because these differences can materially alter DC measurement accuracy even when the pin count is unchanged.
The 0.5 µA standby current belongs to the amplifier’s standby state and does not guarantee that the complete circuit consumes only 0.5 µA. Resistor dividers, sensor bias networks, leakage paths, and control logic can dominate system consumption. During layout, keep the standby-control trace away from sensitive input nodes and ensure that disconnected sensors cannot inject charge into the amplifier outputs. Use the Request a Quote form to confirm the exact MPN and delivery configuration before placing a long-lead-time obsolete-product order.
Place the input and output components associated with each amplifier channel close to their respective pins, and keep the high-impedance input route short to reduce leakage and pickup. The two channels share the same package but are independent circuits, so maintain separate feedback and filtering layouts where channel isolation matters. Connect supply decoupling according to the STMicroelectronics TS902 application guidance and provide an exposed, uninterrupted ground path beneath the SOIC package where the board design supports it.
מידע על תאימות
The retrieved documentation identifies an obsolete-product TS902 datasheet and an industrial temperature range, but it does not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations.