VSC7153XSS-02 - 24-PHY 3Gbps SAS Expander | Analog Devices
MPN: VSC7153XSS-02 ✓ פעילVSC7153XSS-02 סקירה
A SAS expander is a semiconductor interface device that sits within the Serial Attached SCSI hierarchy and manages a group of SAS physical links. In this broader storage hierarchy, the expander provides link aggregation and routing between a host-facing interface and multiple SAS endpoints. The VSC7153XSS-02 combines 24 physical-layer channels with table-based routing, allowing a storage designer to construct scalable fan-in or fan-out topologies rather than connecting every endpoint through a separate host port.
The device’s three principal documented characteristics are its 24-PHY configuration, support for both 1.5 Gbps and 3.0 Gbps SAS link rates, and hardware-assisted table routing through its SSP engine. These features make it relevant to SAS 1.5 and SAS 3.0 system architectures. Because the expander operates in the data path, system-level validation should include link training, negotiated-rate behavior, error handling, topology discovery, and recovery after cable or endpoint faults.
The VSC7153XSS-02 is best understood as a protocol-aware interface component rather than a general-purpose I/O expander. Its PHY count determines how many physical SAS links can participate in a fabric, while the routing engine determines how those links are mapped. In a practical system, this can simplify backplane organization, reduce the number of direct host connections, and provide a defined switching layer between initiators and drive enclosures. Firmware and validation must still confirm routing-table behavior against the exact system topology.
Typical applications include SAS disk-array controllers, storage backplanes, direct-attached storage enclosures, server storage fabrics, and fanout systems that expand a smaller number of host links into a larger set of device links. It is particularly relevant when a design requires table-based routing rather than a simple fixed point-to-point connection. Storage architects should evaluate it alongside controller resources, connector density, cable-length limits, enclosure power, and the target drive-generation requirements.
The primary design consideration is preserving signal integrity across every high-speed SAS path. Differential routing, connector launches, return paths, reference-plane continuity, and compliance testing are central to a reliable implementation. The physical package and pin map must be taken directly from the manufacturer datasheet, while power, ground, thermal, and decoupling decisions should be based on the documented operating limits for the ordered device.
This page organizes the documented VSC7153XSS-02 capabilities, application context, comparison parameters, and engineering checks into a practical reference. It also distinguishes confirmed product facts from parameters that must be established from the manufacturer datasheet, helping procurement, hardware, and validation teams align before beginning an SAS fabric design.
חלופות תחליף ישיר עבור VSC7153XSS-02 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם VSC7153XSS-02 (אותו גורם צורה וטביעת רגל).
אין חלופות תואמות Drop-in עבור מוצר זה.
בקשת חלופותVSC7153XSS-02 מפרטים
| Product Type | SAS edge/fanout expander |
| Physical Layer Count | 24 PHY |
| Supported SAS Link Rate | 1.5 Gbps |
| Supported SAS Link Rate | 3.0 Gbps |
| Routing Architecture | Table routing |
| Routing Engine | SSP engine |
| Device Classification | IC interface controller |
| Fabric Function | SAS edge/fanout expansion |
מדריך תצורת פינים של VSC7153XSS-02 standard
תצורת פינים עבור VSC7153XSS-02 (מארזת standard). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור VSC7153XSS-02.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
VSC7153XSS-02 מתאים עבור 6 יישוםs: SAS Disk-Array Controller Backplane, Direct-Attached Storage Enclosure, Server Storage Fabric Expansion, SAS Edge Switching Layer, External SAS Storage Enclosure, Enterprise Storage Backplane Management.
SAS Disk-Array Controller Backplane
The VSC7153XSS-02 fits a storage backplane that must organize multiple SAS physical links through a controlled routing layer. Its 24 PHYs provide a substantial number of connections, while support for 1.5 Gbps and 3.0 Gbps allows the fabric to accommodate different SAS generations. Table routing and the SSP engine are useful when initiator-to-device paths must be defined and managed dynamically. Implementation should preserve differential-pair geometry, provide uninterrupted reference planes, and validate link training across every supported rate. Firmware must also confirm route-table programming, fault isolation, and recovery behavior.
מומלץ
Direct-Attached Storage Enclosure
A direct-attached storage enclosure can use the VSC7153XSS-02 when it needs to fan a limited number of host-facing SAS links out to numerous drive-side links. The device’s 24-PHY arrangement reduces the need for direct point-to-point wiring across the enclosure backplane, while table routing defines how initiator paths reach selected drives. The 1.5 Gbps and 3.0 Gbps support makes it relevant to mixed-generation SAS storage plans. Before release, engineers should confirm connector and cable reach, power-loss behavior, thermal loading, and whether the enclosure requires hot-swap or redundant-management features not specified in the available summaries.
מומלץ
Server Storage Fabric Expansion
The VSC7153XSS-02 is suitable for a server storage fabric that expands a host interface into a larger endpoint population. Its 24 PHYs and hardware-assisted table routing can consolidate topology management into a dedicated expander layer, allowing storage controllers to address drives through a structured SAS fabric. Using both documented rates, 1.5 Gbps and 3.0 Gbps, supports design planning across different drive and backplane capabilities. Validation should include negotiated-rate interoperability, congestion behavior, PHY fault containment, firmware routing-table updates, and full enclosure power-cycle testing before production deployment.
מומלץ
SAS Edge Switching Layer
The VSC7153XSS-02 can serve as a switching layer between SAS initiators and endpoint devices when the system architecture requires table-driven path control rather than a fixed wiring plan. The SSP engine and 24-PHY count support centralized route management for moderate-density fabrics. This arrangement can simplify point-to-point cabling and make topology changes easier for firmware to manage. Engineering teams should establish how routes are loaded, how duplicate or invalid table entries are handled, and how the fabric responds to link loss. Signal-integrity testing must cover every supported 1.5 Gbps and 3.0 Gbps operating mode.
מומלץ
External SAS Storage Enclosure
An external SAS enclosure is a practical use case for the VSC7153XSS-02 when it must expose multiple drive connections through a managed expander fabric. The 24-PHY organization can support a larger enclosure while table routing controls which host path reaches each drive. The device’s documented 1.5 Gbps and 3.0 Gbps capability allows compatibility planning for two SAS link generations, subject to connector, cable, and target-device constraints. Designers should pay particular attention to power-rail sequencing, startup transients, connector geometry, enclosure airflow, and whether the selected drive mix requires rate conversion or only common-rate operation.
מומלץ
Enterprise Storage Backplane Management
The VSC7153XSS-02 can support enterprise backplanes where a predictable routing table and a high channel count simplify physical design. By placing 24 PHYs behind a table-routing engine, the architecture separates physical link expansion from initiator-side addressing. Support for 1.5 Gbps and 3.0 Gbps provides a common platform for planned SAS generations, although operation across mixed generations must be validated explicitly. Reliability testing should examine hot-plug behavior, power interruption during route updates, PHY error counters, cable faults, and recovery without corrupting the active topology.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור VSC7153XSS-02 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Brand | Analog Devices |
| Product Type | SAS edge/fanout expander |
| Physical Layer Count | 24 PHY |
| Supported Link Rates | 1.5 Gbps and 3.0 Gbps |
| Routing Method | Table routing |
| Routing Engine | SSP engine |
| Device Classification | IC interface controller |
מבדילים עיקריים
- Broad physical-layer count for managed SAS fabrics (לעומתVSC7155VU-02)
- Support for two documented SAS link generations (לעומתVSC7156XYT-03)
- Integrated table-routing architecture (לעומתVSC7147RM-02)
הערות תכנון
Route every SAS differential pair as a controlled impedance transmission line with symmetrical geometry, continuous reference planes, and minimal stubs. Keep PHY connections away from noisy switching paths and use manufacturer-recommended connector and termination arrangements. Validate eye quality, jitter, insertion loss, and return loss at both documented 1.5 Gbps and 3.0 Gbps rates because an acceptable link-training result does not replace physical-layer margin testing.
Build the PCB layer stack around the manufacturer’s package, connector, and high-speed guidance before assigning traces. Maintain continuous ground and power planes beneath the routing region, provide ample via transitions only where the impedance design requires them, and avoid plane splits that interrupt return current. Exact decoupling, via-in-pad, and thermal-relief instructions must come from the datasheet because the package and electrical limits are not identified in the available summaries.
Do not treat the similarly named VSC7153SS-02 or other VSC-family members as automatic substitutes for VSC7153XSS-02. Ordering codes can encode different package, temperature, or qualification options, and the routing functions may not be equivalent. Before schematic reuse or firmware transfer, verify pin names, power rails, reset behavior, clocking, SAS-rate support, interrupt signaling, and the routing-table model against each exact datasheet.
Plan the power tree so the device receives clean, sequenced rails under both normal operation and fault recovery. Assess startup current, rail tolerance, decoupling, and the contribution of neighboring high-speed circuitry before assigning capacitor values. Check power sequencing against the exact enable and reset requirements, and test repetitive power cycles because storage systems must recover cleanly after interrupted route-table updates or enclosure power loss.
מידע על תאימות
Compliance status was not identified in the available product summaries. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status in the manufacturer documentation for the exact ordering code.