AD7472BRZ - 12-Bit 1.5 MSPS ADC | Analog Devices
MPN: AD7472BRZ ✓ सक्रियAD7472BRZ अवलोकन
An ADC converts a continuously varying analog voltage into a numerical value for processing by a microprocessor, digital signal processor, or programmable logic. The AD7472 belongs to the successive-approximation, or SAR, ADC family. SAR converters repeatedly compare the sampled input against an internal reference and a weighted capacitor array. This architecture combines predictable latency, direct sampling control, and a parallel data interface without the clock and filtering complexity of a pipeline converter.
Key characteristics of the AD7472 include 12-bit resolution, throughput up to 1.5 MSPS, a single 2.7 V to 5.25 V analog and digital supply, and a 0 V to 2.5 V input range. Conversion is initiated by the falling edge of CONVST, while BUSY indicates that the conversion is in progress. According to the manufacturer product information, BUSY returns low 531.66 ns after the falling CONVST edge when the internal clock operates at 26 MHz. The parallel interface simplifies connection to older DSP and FPGA systems that do not use serial protocols.
Typical power figures depend on supply voltage and throughput. The AD7472 dissipates approximately 3.34 mW at 1.5 MSPS with 3 V supplies and 7.97 mW at 1.75 MSPS with 5 V supplies, as listed in the component datasheet. This operating range makes the converter suitable for battery-powered measurement equipment, where power dissipation affects both run time and thermal design. The industrial temperature option covers -40°C to +85°C.
The AD7472BRZ is used in portable data loggers, process-control modules, industrial sensor interfaces, ultrasonic measurement systems, and embedded acquisition boards. In these systems, the 12-bit code supports measurement of 2.5 V full-scale signals with an input-referred quantization step of approximately 610 µV when the full 0 V to 2.5 V range is used. External reference and input conditioning circuitry remain important when accuracy, common-mode rejection, or overrange behavior must be controlled.
For implementation, route the analog input and reference paths away from digital switching nodes, place input and reference decoupling capacitors close to their associated pins, and use a short, symmetric digital-output routing pattern. Check the acquisition timing against the 531.66 ns conversion indication and the receiving device setup time. Request a quote on this page for current commercial availability, lead time, and orderable quantities.
के लिए ड्रॉप-इन विकल्प AD7472BRZ — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
AD7472ARZ
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD7470ARZ
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD7470BRZ
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD7472BRZ Maximum Ratings और Electrical Characteristics
| रेज़ोल्यूशन | 12 bit |
| सैंपलिंग रेट | 1.5 MSPS |
| Architecture | Successive approximation (SAR) |
| Number of Inputs | 1 single-ended input |
| Supply Voltage Range | 2.7 V to 5.25 V |
| Analog Input Range | 0 V to 2.5 V |
| Output Interface | 12-bit parallel |
| Conversion Start | Falling edge of CONVST |
| Conversion Busy Time | 531.66 ns at a 26 MHz clock |
| Power Dissipation at 1.5 MSPS | 3.34 mW typical with a 3 V supply |
| Power Dissipation at 1.75 MSPS | 7.97 mW typical with a 5 V supply |
| पैकेज | 24-lead SOIC |
| पिन काउंट | 24 pins |
| ऑपरेटिंग तापमान | -40°C to +85°C |
| Screening Level | Industrial |
| माउंटिंग प्रकार | Surface mount |
AD7472BRZ 24-lead soic पिन कॉन्फ़िगरेशन गाइड
AD7472BRZ (24-lead soic पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: AD7472BRZ.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
AD7472BRZ के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Sensor Signal Acquisition, Portable Battery-Powered Measurement, Process-Control and Monitoring Loops, DSP-Based Data Acquisition, Ultrasonic and Time-Based Measurement, Embedded Test and Measurement.
Industrial Sensor Signal Acquisition
The AD7472BRZ suits industrial sensor channels that produce conditioned, single-ended voltages below 2.5 V. Its 12-bit resolution captures 4096 discrete levels across the 0 V to 2.5 V input range, while throughput up to 1.5 MSPS supports rapid periodic sampling. Place the converter close to the conditioning amplifier to minimize pickup from motor-control and switching circuits. The -40°C to +85°C industrial temperature option supports factory equipment, although the front-end amplifier, protection network, and reference must independently satisfy the required accuracy and common-mode range.
अनुशंसित
Portable Battery-Powered Measurement
A 3.34 mW typical power figure at 1.5 MSPS with a 3 V supply makes the AD7472BRZ practical for portable measurement instruments. The single 2.7 V to 5.25 V supply range allows operation directly from a regulated 3 V rail, and the SAR architecture provides deterministic acquisition timing without a pipeline settling cycle. Power the analog section from a quiet regulator and disable or slow sampling when the application does not require continuous updates. This improves run time while preserving 12-bit data for battery-based loggers and field-service instruments.
अनुशंसित
Process-Control and Monitoring Loops
The AD7472BRZ can digitize fast process variables for feedback control, monitoring, and fault detection. The 1.5 MSPS sampling rate provides up to 667 microseconds between samples, and the falling-edge CONVST input allows sampling to be aligned with an external trigger. A parallel interface connects efficiently to industrial controllers and DSP modules. Control-loop performance still depends on the acquisition loop latency, digital filtering, isolation requirements, and the accuracy of the upstream sensor and signal-conditioning stages.
अनुशंसित
DSP-Based Data Acquisition
The AD7472BRZ is appropriate for DSP acquisition cards because its 12-bit parallel output exposes the complete conversion result without a serial deserializer. The controller can read the data bus after BUSY indicates conversion completion, then apply digital filtering, calibration, or spectral analysis. With the internal clock at 26 MHz, BUSY falls 531.66 ns after the falling CONVST edge according to the datasheet. Confirm receiver setup and hold timing, and keep the 12 output traces short enough to preserve signal integrity at the operating clock rate.
अनुशंसित
Ultrasonic and Time-Based Measurement
Periodic ultrasonic or time-of-flight measurements benefit from a converter with direct conversion-start control and a deterministic busy interval. The AD7472BRZ samples on the falling edge of CONVST and can reach 1.5 MSPS, allowing dense point sets to be captured when the analog front end provides adequate bandwidth and dynamic range. Use CONVST for coherent sampling and trigger timing. Keep the analog path short and place the input decoupling network close to the converter to reduce timing errors that would otherwise shift the apparent arrival time.
अनुशंसित
Embedded Test and Measurement
The AD7472BRZ can digitize low-level test signals in embedded instrumentation, waveform monitors, and automated test equipment. Its 12-bit resolution improves measurement granularity compared with a 10-bit converter, while the compact 24-lead SOIC simplifies board construction. The parallel output requires enough digital I/O on the controller, so a multiplexing device or dedicated acquisition controller may be needed in compact systems. Establish calibration against the precision reference, include gain and offset correction in firmware, and verify input bandwidth before increasing the sampling rate.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा AD7472BRZ — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | AD7472ARZ | AD7470ARZ | AD7470BRZ |
|---|---|---|---|---|
| Package | 24-lead SOIC | 24-lead SOIC | 24-lead SOIC | 24-lead SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Resolution | 12 bit | 12 bit | 10 bit | 10 bit |
| Maximum Throughput | 1.5 MSPS | 1.5 MSPS | 1.75 MSPS | 1.75 MSPS |
| Supply Voltage Range | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V |
| Analog Input Range | 0 V to 2.5 V | 0 V to 2.5 V | 0 V to 2.5 V | 0 V to 2.5 V |
| Architecture | Successive approximation, 1 input | Successive approximation, 1 input | Successive approximation, 1 input | Successive approximation, 1 input |
| Output Interface | 12-bit parallel | 12-bit parallel | 10-bit parallel | 10-bit parallel |
मुख्य विशेषताएँ
- Higher resolution within the AD7470/AD7472 family (बनामAD7470BRZ)
- Direct same-family package-compatible option (बनामAD7472ARZ)
- Balanced resolution and acquisition speed (बनामAD7470ARZ)
डिज़ाइन नोट्स
Route the analog input directly to the converter and place its decoupling capacitor next to the corresponding supply or reference pins. Keep the input trace short and place the sensor or amplifier output driver close enough to avoid loading the input network. Digital output traces may be longer than the analog trace, but route them away from the reference and input nodes to reduce conversion errors.
Use BUSY as the primary indication that the 12 parallel output bits are valid, and account for the documented 531.66 ns conversion interval at a 26 MHz internal clock. Confirm the receiving device setup and hold requirements in the system timing budget. A synchronous interface using CONVST and BUSY is preferable to polling the data bus independently of the conversion state.
Do not treat the 0 V to 2.5 V analog input range as permission to exceed it during transients or startup. Use suitable clamping and source-impedance limits, and verify the source settling time against the acquisition requirements. Also verify that any substitute retains the same supply range, pin functions, resolution, temperature grade, and acquisition timing before populating it on an existing board.
Estimated power consumption is 3.34 mW at 1.5 MSPS with a 3 V supply, using the datasheet value directly rather than a derived junction-temperature calculation. In a portable instrument, reduce the conversion rate when continuous full-speed sampling is unnecessary and power the analog section from a low-noise supply. Account for reference and signal-conditioning power when calculating the complete acquisition-channel budget.
अनुपालन जानकारी
The component is identified as an industrial-temperature 24-lead SOIC ADC. RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification data are not stated in the manufacturer product information excerpt, so these fields remain unknown.