AD7472BRZ - 12-Bit 1.5 MSPS ADC | Analog Devices
MPN: AD7472BRZ ✓ 啟用中AD7472BRZ 概覽
An ADC converts a continuously varying analog voltage into a numerical value for processing by a microprocessor, digital signal processor, or programmable logic. The AD7472 belongs to the successive-approximation, or SAR, ADC family. SAR converters repeatedly compare the sampled input against an internal reference and a weighted capacitor array. This architecture combines predictable latency, direct sampling control, and a parallel data interface without the clock and filtering complexity of a pipeline converter.
Key characteristics of the AD7472 include 12-bit resolution, throughput up to 1.5 MSPS, a single 2.7 V to 5.25 V analog and digital supply, and a 0 V to 2.5 V input range. Conversion is initiated by the falling edge of CONVST, while BUSY indicates that the conversion is in progress. According to the manufacturer product information, BUSY returns low 531.66 ns after the falling CONVST edge when the internal clock operates at 26 MHz. The parallel interface simplifies connection to older DSP and FPGA systems that do not use serial protocols.
Typical power figures depend on supply voltage and throughput. The AD7472 dissipates approximately 3.34 mW at 1.5 MSPS with 3 V supplies and 7.97 mW at 1.75 MSPS with 5 V supplies, as listed in the component datasheet. This operating range makes the converter suitable for battery-powered measurement equipment, where power dissipation affects both run time and thermal design. The industrial temperature option covers -40°C to +85°C.
The AD7472BRZ is used in portable data loggers, process-control modules, industrial sensor interfaces, ultrasonic measurement systems, and embedded acquisition boards. In these systems, the 12-bit code supports measurement of 2.5 V full-scale signals with an input-referred quantization step of approximately 610 µV when the full 0 V to 2.5 V range is used. External reference and input conditioning circuitry remain important when accuracy, common-mode rejection, or overrange behavior must be controlled.
For implementation, route the analog input and reference paths away from digital switching nodes, place input and reference decoupling capacitors close to their associated pins, and use a short, symmetric digital-output routing pattern. Check the acquisition timing against the 531.66 ns conversion indication and the receiving device setup time. Request a quote on this page for current commercial availability, lead time, and orderable quantities.
直接替換替代品,適用於 AD7472BRZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
AD7472ARZ
✅ 直接替換📋 參考替代品(不在目錄中)
AD7470ARZ
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD7470BRZ
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD7472BRZ 最大額定值與電氣特性
| 解析度 | 12 bit |
| 取樣率 | 1.5 MSPS |
| Architecture | Successive approximation (SAR) |
| Number of Inputs | 1 single-ended input |
| Supply Voltage Range | 2.7 V to 5.25 V |
| Analog Input Range | 0 V to 2.5 V |
| Output Interface | 12-bit parallel |
| Conversion Start | Falling edge of CONVST |
| Conversion Busy Time | 531.66 ns at a 26 MHz clock |
| Power Dissipation at 1.5 MSPS | 3.34 mW typical with a 3 V supply |
| Power Dissipation at 1.75 MSPS | 7.97 mW typical with a 5 V supply |
| 封裝 | 24-lead SOIC |
| 腳位數 | 24 pins |
| 工作溫度 | -40°C to +85°C |
| Screening Level | Industrial |
| 安裝類型 | Surface mount |
AD7472BRZ 24-lead soic 腳位配置指南
AD7472BRZ(24-lead soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD7472BRZ.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD7472BRZ 適用於 6 應用s: Industrial Sensor Signal Acquisition, Portable Battery-Powered Measurement, Process-Control and Monitoring Loops, DSP-Based Data Acquisition, Ultrasonic and Time-Based Measurement, Embedded Test and Measurement.
Industrial Sensor Signal Acquisition
The AD7472BRZ suits industrial sensor channels that produce conditioned, single-ended voltages below 2.5 V. Its 12-bit resolution captures 4096 discrete levels across the 0 V to 2.5 V input range, while throughput up to 1.5 MSPS supports rapid periodic sampling. Place the converter close to the conditioning amplifier to minimize pickup from motor-control and switching circuits. The -40°C to +85°C industrial temperature option supports factory equipment, although the front-end amplifier, protection network, and reference must independently satisfy the required accuracy and common-mode range.
推薦
Portable Battery-Powered Measurement
A 3.34 mW typical power figure at 1.5 MSPS with a 3 V supply makes the AD7472BRZ practical for portable measurement instruments. The single 2.7 V to 5.25 V supply range allows operation directly from a regulated 3 V rail, and the SAR architecture provides deterministic acquisition timing without a pipeline settling cycle. Power the analog section from a quiet regulator and disable or slow sampling when the application does not require continuous updates. This improves run time while preserving 12-bit data for battery-based loggers and field-service instruments.
推薦
Process-Control and Monitoring Loops
The AD7472BRZ can digitize fast process variables for feedback control, monitoring, and fault detection. The 1.5 MSPS sampling rate provides up to 667 microseconds between samples, and the falling-edge CONVST input allows sampling to be aligned with an external trigger. A parallel interface connects efficiently to industrial controllers and DSP modules. Control-loop performance still depends on the acquisition loop latency, digital filtering, isolation requirements, and the accuracy of the upstream sensor and signal-conditioning stages.
推薦
DSP-Based Data Acquisition
The AD7472BRZ is appropriate for DSP acquisition cards because its 12-bit parallel output exposes the complete conversion result without a serial deserializer. The controller can read the data bus after BUSY indicates conversion completion, then apply digital filtering, calibration, or spectral analysis. With the internal clock at 26 MHz, BUSY falls 531.66 ns after the falling CONVST edge according to the datasheet. Confirm receiver setup and hold timing, and keep the 12 output traces short enough to preserve signal integrity at the operating clock rate.
推薦
Ultrasonic and Time-Based Measurement
Periodic ultrasonic or time-of-flight measurements benefit from a converter with direct conversion-start control and a deterministic busy interval. The AD7472BRZ samples on the falling edge of CONVST and can reach 1.5 MSPS, allowing dense point sets to be captured when the analog front end provides adequate bandwidth and dynamic range. Use CONVST for coherent sampling and trigger timing. Keep the analog path short and place the input decoupling network close to the converter to reduce timing errors that would otherwise shift the apparent arrival time.
推薦
Embedded Test and Measurement
The AD7472BRZ can digitize low-level test signals in embedded instrumentation, waveform monitors, and automated test equipment. Its 12-bit resolution improves measurement granularity compared with a 10-bit converter, while the compact 24-lead SOIC simplifies board construction. The parallel output requires enough digital I/O on the controller, so a multiplexing device or dedicated acquisition controller may be needed in compact systems. Establish calibration against the precision reference, include gain and offset correction in firmware, and verify input bandwidth before increasing the sampling rate.
推薦
推薦產品摘要
工程參考資料,適用於 AD7472BRZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD7472ARZ | AD7470ARZ | AD7470BRZ |
|---|---|---|---|---|
| Package | 24-lead SOIC | 24-lead SOIC | 24-lead SOIC | 24-lead SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Resolution | 12 bit | 12 bit | 10 bit | 10 bit |
| Maximum Throughput | 1.5 MSPS | 1.5 MSPS | 1.75 MSPS | 1.75 MSPS |
| Supply Voltage Range | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V |
| Analog Input Range | 0 V to 2.5 V | 0 V to 2.5 V | 0 V to 2.5 V | 0 V to 2.5 V |
| Architecture | Successive approximation, 1 input | Successive approximation, 1 input | Successive approximation, 1 input | Successive approximation, 1 input |
| Output Interface | 12-bit parallel | 12-bit parallel | 10-bit parallel | 10-bit parallel |
主要差異化特點
- Higher resolution within the AD7470/AD7472 family (對比AD7470BRZ)
- Direct same-family package-compatible option (對比AD7472ARZ)
- Balanced resolution and acquisition speed (對比AD7470ARZ)
設計說明
Route the analog input directly to the converter and place its decoupling capacitor next to the corresponding supply or reference pins. Keep the input trace short and place the sensor or amplifier output driver close enough to avoid loading the input network. Digital output traces may be longer than the analog trace, but route them away from the reference and input nodes to reduce conversion errors.
Use BUSY as the primary indication that the 12 parallel output bits are valid, and account for the documented 531.66 ns conversion interval at a 26 MHz internal clock. Confirm the receiving device setup and hold requirements in the system timing budget. A synchronous interface using CONVST and BUSY is preferable to polling the data bus independently of the conversion state.
Do not treat the 0 V to 2.5 V analog input range as permission to exceed it during transients or startup. Use suitable clamping and source-impedance limits, and verify the source settling time against the acquisition requirements. Also verify that any substitute retains the same supply range, pin functions, resolution, temperature grade, and acquisition timing before populating it on an existing board.
Estimated power consumption is 3.34 mW at 1.5 MSPS with a 3 V supply, using the datasheet value directly rather than a derived junction-temperature calculation. In a portable instrument, reduce the conversion rate when continuous full-speed sampling is unnecessary and power the analog section from a low-noise supply. Account for reference and signal-conditioning power when calculating the complete acquisition-channel budget.
合規資訊
The component is identified as an industrial-temperature 24-lead SOIC ADC. RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification data are not stated in the manufacturer product information excerpt, so these fields remain unknown.