ADF4118BRUZ-RL7 - 3 GHz RF PLL Synthesizer | Analog Devices
MPN: ADF4118BRUZ-RL7 ✓ सक्रियADF4118BRUZ-RL7 अवलोकन
A frequency synthesizer is a phase-locked-loop, or PLL, component that locks an output frequency to a stable reference. In the ADF4118, the programmable dividers and counters determine how the phase-frequency detector compares the divided feedback signal with the reference. When the feedback and reference agree, the charge pump corrects the output until the loop reaches lock. This architecture provides programmable RF output for communication equipment while requiring an external reference, loop filter, voltage-controlled oscillator, and RF output network.
The ADF4118 family's principal features include a 3 GHz operating ceiling, one synthesizer channel, a digital phase-frequency detector, a precision charge pump, and programmable reference, A-counter, and B-counter functions. The dual-modulus prescaler supports fractional-N synthesis techniques by allowing the programmable counters to represent ratios that cannot be produced through integer division alone. The low-noise phase-frequency detector helps establish low phase noise in the synthesized output, while the charge pump controls loop current and correction behavior.
The ADF4118BRUZ-RL7 is differentiated by its 16-lead TSSOP surface-mount package and the -RL7 production configuration. The package is suitable for automated assembly and compact RF modules. As with any high-frequency PLL, performance depends on the external reference source, loop filter, voltage-controlled oscillator, power-supply layout, and impedance-matched PCB traces. The datasheet's application and pin-description tables should govern the final reference design rather than assumptions based only on the family-level architecture.
Typical uses include wireless receiver and transmitter local oscillators, up-converters and down-converters, RF instrumentation, communication transceivers, and frequency-generation modules. The synthesizer can support programmable channels where one reference drives multiple selectable output frequencies. Component selection should include the required output range, reference frequency, prescaler range, channel spacing, phase-noise target, tuning bandwidth, and regulatory requirements for the finished equipment.
Keep the reference and feedback routes short and impedance controlled, and place the loop-filter components near the relevant device pins. Use a clean, well-decoupled supply because supply ripple can degrade phase noise and spur performance. A careful grounding strategy and short RF output path are equally important; the digital programming interface and sensitive RF nodes should not share uncontrolled return-current paths.
This product page combines the manufacturer architecture and package information with practical PLL design guidance, verified source links, and a conservative review of replacement options. It helps engineers identify the correct ADF4118 configuration, distinguish true drop-in devices from packaging-only variants, and plan RF layout, loop-filter implementation, sourcing, and qualification.
के लिए ड्रॉप-इन विकल्प ADF4118BRUZ-RL7 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं ADF4118BRUZ-RL7 (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न A Counter, B Counter, Charge Pump, Package, Prescaler.
इस उत्पाद के लिए कोई drop-in alternatives उपलब्ध नहीं।
विकल्प अनुरोध करेंADF4118BRUZ-RL7 विशेषताएं
| Device Type | Single-channel RF PLL frequency synthesizer |
| Maximum Operating Frequency | 3 GHz |
| Output Channels | 1 channel |
| Phase-Frequency Detector | 1 digital low-noise PFD |
| Charge Pump | 1 precision charge pump |
| A Counter | 5-bit programmable counter |
| B Counter | 5-bit programmable counter |
| Prescaler | Dual-modulus P/P+1 prescaler |
| Reference Divider | Programmable |
| पैकेज | 16-lead TSSOP, 4.40 mm width |
| Package Width | 4.40 mm |
| Package Body Width | 0.173 inch |
| माउंटिंग प्रकार | Surface mount |
ADF4118BRUZ-RL7 0.173 inch पिन कॉन्फ़िगरेशन गाइड
ADF4118BRUZ-RL7 (0.173 inch पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: ADF4118BRUZ-RL7.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
ADF4118BRUZ-RL7 के लिए उपयुक्त है 6 अनुप्रयोगs: Wireless Receiver Local Oscillator, RF Transmitter Up-Converter, RF Down-Converter Local Oscillator, Programmable RF Signal Source, RF Communication Module, RF Instrumentation Front End.
Wireless Receiver Local Oscillator
The ADF4118BRUZ-RL7 fits a wireless receiver local-oscillator block because its phase-locked-loop architecture can divide a stable reference into a programmable RF output, with operation extending to 3 GHz. The 5-bit A and B counters, programmable reference divider, and dual-modulus P/P+1 prescaler support flexible channel-ratio generation. The synthesizer is paired with an external VCO and loop filter, so final phase noise, spur performance, and lock time depend on those components as well as the reference source. Use short, controlled feedback and RF routes and follow the manufacturer layout guidance to minimize added noise and phase error.
अनुशंसित
RF Transmitter Up-Converter
In an RF transmitter up-converter, the ADF4118BRUZ-RL7 can generate the programmable local-oscillator reference used by a mixer to translate information from an intermediate frequency toward the transmit band. Its 3 GHz ceiling and programmable divider and counter architecture allow the synthesizer to support multiple transmit frequencies from one reference. The external VCO must cover the desired band and provide suitable tuning gain and phase noise, while the loop filter must meet both locking-time and spur requirements. PCB planning should isolate the VCO and output-matching network from digital control traces and switching supply return paths.
अनुशंसित
RF Down-Converter Local Oscillator
The ADF4118BRUZ-RL7 is applicable to the down-conversion local oscillator in wireless receivers, instrumentation, and communication equipment operating below its 3 GHz ceiling. It uses the programmable reference divider, 5-bit A and B counters, and dual-modulus prescaler to establish the required feedback ratio between the external VCO and the system reference. Because the synthesizer does not contain the VCO itself, design teams must verify tuning range, gain, and noise performance in the selected oscillator. The loop filter and layout should be evaluated together to prevent excessive ripple, poor lock behavior, or degraded adjacent-channel performance.
अनुशंसित
Programmable RF Signal Source
The ADF4118BRUZ-RL7 can serve as the synthesis core of a programmable RF signal source when a stable reference, external VCO, and suitable loop filter are available. Its single channel provides a straightforward way to obtain one selectable RF output while supporting programmable division ratios through the counter and prescaler architecture. This arrangement is useful for bench equipment and communication test modules that require controlled frequency selection. Component selection should account for the reference frequency, allowed prescaler ratios, desired tuning resolution, and output range. The 16-lead TSSOP package also supports compact, automated assembly without changing the general surface-mount implementation approach.
अनुशंसित
RF Communication Module
The ADF4118BRUZ-RL7 fits compact RF communication modules requiring a programmable local oscillator with an operating ceiling of 3 GHz. Its phase-frequency detector, precision charge pump, programmable reference divider, counters, and dual-modulus prescaler support flexible synthesis ratios from a shared reference. The part is particularly useful when a module must cover several transmit or receive channels rather than using a fixed oscillator. The external VCO remains essential, and the complete implementation should verify lock range, temperature behavior, phase noise, and supply rejection. Compact construction also demands careful ground-plane continuity and controlled impedance around the RF output path.
अनुशंसित
RF Instrumentation Front End
The ADF4118BRUZ-RL7 can support programmable local-oscillator generation in RF instrumentation front ends operating within the 3 GHz range. Using a common reference and programmable feedback ratios allows measurement equipment to select different test frequencies while preserving phase coherence between channels. The reference divider, 5-bit counters, and dual-modulus prescaler make the synthesizer suitable for flexible ratio generation, although exact channel resolution must be confirmed from the device limits. Measurement accuracy also depends on reference purity and VCO performance, so the design should avoid coupling switching-converter noise into the reference or RF supply paths.
अनुशंसित
के लिए इंजीनियरिंग संदर्भ डेटा ADF4118BRUZ-RL7 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद |
|---|---|
| Package | 16-lead TSSOP, 4.40 mm width |
| Brand | Analog Devices |
| Product Type | Single-channel RF PLL frequency synthesizer |
| Maximum Operating Frequency | 3 GHz |
| Phase-Frequency Detector | Low-noise digital PFD |
| Charge Pump | Precision charge pump |
| Counter Width | 5-bit A and B counters |
| Prescaler | Dual-modulus P/P+1 |
| Reference Divider | Programmable |
मुख्य विशेषताएँ
- Higher supported operating frequency than the related ADF4107 family (बनामADF4107BRUZ)
- Clear RF-synthesizer feature set (बनामADF4107BRUZ)
- Compact automated-assembly package (बनामADF4107BRUZ)
डिज़ाइन नोट्स
Follow the Analog Devices ADF4116/ADF4117/ADF4118 datasheet layout guidance for the reference, feedback, charge-pump, supply, and RF connections. Keep sensitive paths short, preserve a continuous ground plane, and place loop-filter components close to their associated pins. Determine controlled-impedance dimensions from the PCB stack-up and target RF impedance. Do not use the shared TSSOP outline as proof that a board can replace one PLL family with another without checking every pin function.
Decouple each supply connection at the device with the capacitance and routing specified by the manufacturer. Because phase noise and reference suppression can be affected by supply ripple, use a stable reference source and prevent switching-converter return current from crossing the sensitive RF and PLL areas. If the product option provides multiple supply domains, observe the sequencing and voltage limits in the datasheet rather than assuming that all pins have identical requirements.
Do not treat ADF4118 order codes that differ only by packaging or suffix as engineering alternatives without checking the ordering table and qualification details. Likewise, a same-package PLL from another family may have different counter widths, prescaler ranges, reference limits, programming registers, or pin assignments. For every proposed substitution, perform a pin-by-pin and parameter-by-parameter comparison against the original ADF4118BRUZ-RL7 datasheet before approving the change.
अनुपालन जानकारी
Compliance attributes require confirmation from the current Analog Devices product documentation or material declaration for the exact ordering code.