Texas Instruments

INA141UA/2K5 - Precision 10/100 Instrumentation Amplifier | TI

MPN: INA141UA/2K5 ✓ सक्रिय
±2.25 V to ±18 V Vdss 5 nA maximum Id 8-pin SOIC (D) Package
न्यूनतम ऑर्डर मात्रा: 1 |

INA141UA/2K5 अवलोकन

The Texas Instruments INA141UA/2K5 is a precision, low-power, single-channel instrumentation amplifier with selectable gains of 10 V/V and 100 V/V, supplied in an 8-pin SOIC package. It operates from a minimum ±2.25 V supply to a maximum ±18 V supply, making it suitable for bipolar and single-supply signal-conditioning systems. The device is specified over a -40°C to +85°C temperature range and provides 200 kHz bandwidth at a gain of 100 V/V.

An instrumentation amplifier is a specialized analog amplifier designed to amplify small differential signals while rejecting common-mode interference. The INA141 belongs to the broader hierarchy of instrumentation amplifiers, differential amplifiers, analog amplifiers, and integrated circuits. Its internal three-op-amp architecture and current-feedback input stage provide accurate gain control and useful bandwidth when operating at the higher 100 V/V gain setting. The device is commonly used where sensor outputs are small and the surrounding environment contains significant common-mode voltage.

The main electrical features include low offset voltage of 50 µV maximum, low offset drift of 0.5 µV/°C maximum, low input bias current of 5 nA maximum, and a common-mode rejection ratio of 117 dB minimum. The inputs are protected against ±40 V signals, while the wide ±18 V supply capability supports higher-level analog systems. These characteristics make the amplifier suitable for bridge sensors, biomedical instrumentation, industrial measurement, and precision current sensing.

The INA141 uses a three-op-amp instrumentation-amplifier architecture. Its gain can be selected at 10 V/V or 100 V/V rather than continuously adjusted, which simplifies calibration and reduces the number of external precision resistors required. Current-feedback input circuitry maintains 200 kHz bandwidth at gain 100, a useful result for applications that need faster settling than a conventional fixed-gain amplifier can provide. Input protection is important in industrial systems because transients can appear on sensor wiring before external protection networks fully respond.

Typical applications include Wheatstone bridge amplification, pressure and load-cell signal conditioning, isolated or battery-powered measurement systems, and low-level differential sensor interfaces. The ±40 V input protection can improve robustness when a sensor line is exposed to accidental overload, while the 117 dB minimum common-mode rejection helps preserve accuracy when the signal is small relative to the common-mode voltage. The 8-pin SOIC package also supports compact, surface-mount PCB layouts.

Designers should pay close attention to supply headroom, input common-mode range, output swing, and grounding when selecting the gain setting. Decoupling capacitors should be placed close to the supply pins, and the input and reference pins should be routed away from noisy switching nodes. The gain setting should be selected only after checking the available output swing and the sensor’s full-scale differential range.

This page combines the Texas Instruments product information, verified distributor availability information, same-package replacement references, and practical engineering guidance to support component selection, PCB design, and sourcing. It also distinguishes the exact INA141UA/2K5 ordering code from related INA141 variants so engineers can evaluate fit without treating every related amplifier as an exact replacement.

के लिए ड्रॉप-इन विकल्प INA141UA/2K5 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं INA141UA/2K5 (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Supply Voltage Range, Amplifier Type, Architecture, Gain.

Texas Instruments
Package: 8-pin PDIP
Amplifier Type: Precision fixed-gain instrumentation amplifier
Gain: 100 V/V
Texas Instruments
Supply Voltage Range: 2.25 V to 18 V
Amplifier Type: Precision instrumentation amplifier
Texas Instruments
Package: 8-pin SOIC
Architecture: Three-op-amp instrumentation amplifier
Texas Instruments
Package: 8-pin SOIC
Supply Voltage Range: ±18 V
Amplifier Type: Instrumentation amplifier

INA141UA

✅ ड्रॉप-इन
Texas Instruments
📦 8-pin SOIC (D)
Instrumentation amplifier · Three-op-amp design · 1 circuit · 10 V/V or 100 V/V · 200 kHz · 50 µV · 0.5 µV/°C · 5 nA

कीमत के लिए संपर्क करें

डेटाशीट देखें →

INA141U

✅ ड्रॉप-इन
Texas Instruments
📦 8-pin SOIC (D)
Precision, low-power instrumentation amplifier · Three-op-amp instrumentation amplifier · 10 V/V or 100 V/V · ±0.05% at G = 10 · 50 µV maximum · 0.5 µV/°C maximum · 5 nA maximum · 117 dB minimum

कीमत के लिए संपर्क करें

डेटाशीट देखें →

INA141UA/2K5G4

✅ ड्रॉप-इन
📦 8-pin SOIC (D)
Same INA141UA/2K5 ordering family and 8-SOIC package, but the G4 suffix is identified as obsolete, creating a lifecycle disadvantage

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

INA141UA/2K5E4

✅ ड्रॉप-इन
📦 8-pin SOIC (D)
Same INA141UA/2K5 ordering family and 8-SOIC package; the E4 suffix identifies a related catalog variant and requires exact suffix-level qualification

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

INA131AP

✅ ड्रॉप-इन
Texas Instruments
📦 8-pin SOIC (D)
Precision fixed-gain instrumentation amplifier · 1 circuit · 100 V/V · 70 kHz · 0.7 V/µs · 125 µV maximum · 0.25 µV/°C maximum

कीमत के लिए संपर्क करें

डेटाशीट देखें →

INA131BP

✅ ड्रॉप-इन
Texas Instruments
📦 8-pin SOIC (D)
Precision instrumentation amplifier · 3 amplifiers · 100 V/V · Fixed gain · 2.25 V to 18 V · 50 V · 70 kHz · 0.7 V/µs

कीमत के लिए संपर्क करें

डेटाशीट देखें →

INA141UA/2K5 Maximum Ratings और Electrical Characteristics

Product Type Precision instrumentation amplifier
Number of Channels 1 channel
Gain 10 V/V or 100 V/V
Supply Voltage Range ±2.25 V to ±18 V
Maximum Supply Voltage 36 V total
Input Offset Voltage 50 µV maximum
Input Offset Voltage Drift 0.5 µV/°C maximum
Input Bias Current 5 nA maximum
Common-Mode Rejection Ratio 117 dB minimum
Input Protection Range ±40 V
Bandwidth at Gain 100 200 kHz
ऑपरेटिंग तापमान रेंज -40°C to +85°C
पैकेज 8-pin SOIC (D)
माउंटिंग प्रकार Surface mount
Architecture Three-op-amp instrumentation amplifier with current-feedback input circuitry

INA141UA/2K5 8-pin soic (d) पिन कॉन्फ़िगरेशन गाइड

INA141UA/2K5 (8-pin soic (d) पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।

INA141UA/2K5 के लिए 8-pin soic (d) पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: INA141UA/2K5.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

INA141UA/2K5 के लिए उपयुक्त है 6 अनुप्रयोगs: Load Cell and Pressure Sensor Amplification, Industrial Current Sensing, Medical and Biopotential Signal Conditioning, Precision Bridge and Strain Measurement, Portable and Battery-Powered Instrumentation, Data Acquisition and Test Equipment.

🏭

Load Cell and Pressure Sensor Amplification

The INA141UA/2K5 fits Wheatstone-bridge front ends that produce millivolt-level differential signals while rejecting a much larger common-mode voltage. Its selectable 10 V/V and 100 V/V gains provide useful scaling without a continuously adjustable gain network, while 50 µV maximum offset voltage limits signal error near the measurement floor. The 117 dB minimum common-mode rejection is particularly useful when bridge excitation and ground gradients dominate the differential output. In implementation, place the amplifier close to the bridge, balance the two input routes, and verify that the selected gain keeps the full bridge output inside the device output-swing range.

⚡

Industrial Current Sensing

The INA141UA/2K5 is appropriate for amplifying the small differential voltage produced by a current shunt or current-transformer output. Gain 10 can preserve headroom for moderate signals, while gain 100 increases sensitivity when the shunt voltage is small. Its low 5 nA maximum input bias current helps avoid measurement error with high-impedance sensing networks, and the current-feedback input stage supports 200 kHz bandwidth at gain 100 for faster transient capture. Keep the shunt or sensor return close to the amplifier ground reference, use matched input traces, and avoid sharing those routes with switching power nodes.

💊

Medical and Biopotential Signal Conditioning

The INA141UA/2K5 can condition low-amplitude differential signals in biomedical instrumentation when electrode or sensor signals require common-mode suppression. Its selectable gains support two measurement ranges, and its 117 dB minimum common-mode rejection helps isolate small differential components from body-coupled or equipment-induced common-mode voltage. The ±40 V input protection rating is useful for robust sensor interfaces, but protection-state behavior and applicable medical system requirements must be evaluated carefully. Use guarded grounding, isolated power where required, and carefully isolated routing so the analog input network does not become an unintended current path.

🏭

Precision Bridge and Strain Measurement

The INA141UA/2K5 supports strain-gauge and resistive-bridge systems where excitation produces a small differential signal around a common-mode voltage. Gain 100 increases the signal level for ADC capture, while the 200 kHz bandwidth supports measurements faster than static weighing alone. Low offset voltage of 50 µV maximum and low drift of 0.5 µV/°C maximum help maintain accuracy across temperature changes. For best results, use stable excitation, low-noise reference grounding, matched input routing, and calibration that covers the selected gain range and expected sensor temperature range.

📱

Portable and Battery-Powered Instrumentation

The INA141UA/2K5 suits portable test and measurement equipment that must amplify differential sensor signals while operating from limited supply voltage. Its compact 8-pin SOIC package simplifies board integration, and the architecture supports gains of 10 V/V and 100 V/V for matching different sensor ranges. Operation begins at ±2.25 V, although usable signal range still depends on output swing, common-mode limits, and the selected gain. Low-power design should account for both the amplifier's own consumption and the sensor excitation current, while using local bypass capacitance to keep supply noise from reducing common-mode rejection.

🖥️

Data Acquisition and Test Equipment

The INA141UA/2K5 is useful in bench instruments and data-acquisition systems that must amplify small differential sources before conversion by an ADC. Gain 10 provides moderate attenuation of the source signal, while gain 100 supports high-resolution measurements with small full-scale outputs. The 200 kHz bandwidth at gain 100 accommodates many higher-speed acquisition tasks, and the single-channel SOIC package leaves board space for additional channels. Designers should account for ADC input range, acquisition time, settling behavior, grounding, and connector protection rather than treating the amplifier as a complete front end.

What is the INA141UA/2K5 and what are its key specifications?
The INA141UA/2K5 is a single-channel, precision, low-power instrumentation amplifier with selectable gains of 10 V/V and 100 V/V in an 8-pin SOIC package. According to the Texas Instruments INA141 product information, it operates from ±2.25 V to ±18 V, has 200 kHz bandwidth at gain 100, and is specified from -40°C to +85°C. It is intended for low-level differential measurement where common-mode rejection and input protection are important.
What is the operating voltage of INA141UA/2K5?
The INA141UA/2K5 operates from a minimum supply of ±2.25 V and a maximum supply of ±18 V. Texas Instruments describes the device as having a wide supply range, with the ordering information identifying the INA141UA/2K5 as an 8-pin SOIC device rated from -40°C to +85°C. Designers should also verify the input common-mode and output-swing limits for the selected gain before using a 2.25 V supply.
Where can I download the INA141UA/2K5 datasheet PDF?
The official Texas Instruments INA141 datasheet is available from the manufacturer product-link URL https://www.ti.com/lit/gpn/INA141. The manufacturer product page also provides ordering, quality, and application information for INA141UA/2K5. Use the manufacturer datasheet for the complete pin-description table, electrical characteristics, input protection limits, and recommended application circuit before finalizing a PCB design.
Where can I find the INA141UA/2K5 pinout?
Use the pin-description table in the Texas Instruments INA141 datasheet and the 8-pin SOIC package drawing to locate INA141UA/2K5 pins. The part is explicitly identified as an 8-pin SOIC (D) device. Assign supply, ground, input, reference, feedback, and gain-control nets only after checking the exact pin numbers and the gain-setting logic shown in the manufacturer datasheet.
What is the best drop-in replacement for INA141UA/2K5?
The INA141UA is the closest same-package replacement listed for the INA141UA/2K5 because it uses the same INA141UA 8-SOIC ordering family and retains the 10 V/V and 100 V/V gain options. The INA141U, INA141UA/2K5G4, and INA141UA/2K5E4 are also related 8-pin entries, but production status, gain code, and exact temperature or package suffix must be checked before substitution.
Can INA141U replace INA141UA/2K5?
The INA141U is a related 8-SOIC INA141 variant and is a candidate for footprint-compatible review. A Texas Instruments comparison result lists the same maximum supply of 36 V, minimum supply of 4.5 V, maximum input offset of 50 µV, and minimum gain of 10 V/V. Verify the exact gain configuration, pin functions, temperature rating, and availability before treating it as a drop-in replacement.
Is INA141UA/2K5 the same as INA148UA/2K5?
No. INA141UA/2K5 and INA148UA/2K5 are different Texas Instruments instrumentation-amplifier families. The INA141 provides selectable gains of 10 and 100 V/V, while the INA148 belongs to a different gain-set family. A related 8-SOIC footprint alone does not establish functional interchangeability, so verify gain logic, bandwidth, offset, supply limits, and pin behavior in each manufacturer datasheet.
When should I choose INA141UA/2K5 over INA141UA?
Choose INA141UA/2K5 when the exact 2K5 ordering code, specified gain configuration, and manufacturer-supported configuration are required for the design. Choose INA141UA when its exact ordering suffix and supported gain settings meet the system requirements. Both are associated with the INA141UA 8-SOIC family, so the selection should be based on confirmed pin behavior, grade, lifecycle, and orderable configuration rather than package alone.
Is INA141UA/2K5 suitable for bridge sensor and load-cell applications?
Yes, the INA141UA/2K5 fits low-level bridge measurements because it offers selectable gains of 10 and 100 V/V, 50 µV maximum input offset voltage, and 117 dB minimum common-mode rejection. The 200 kHz bandwidth at gain 100 supports many industrial sensing systems. Output-swing and common-mode-range checks remain necessary because the available headroom depends on the selected supply and gain.
How much common-mode rejection does INA141UA/2K5 provide?
The INA141UA/2K5 provides a minimum common-mode rejection ratio of 117 dB according to the Texas Instruments INA141 product information. This specification is valuable when a small differential sensor signal sits on a larger common-mode voltage. Actual system rejection also depends on resistor matching, source impedance balance, frequency, PCB layout, and the quality of the sensor grounding.
Can the inputs of INA141UA/2K5 tolerate ±40 V?
Yes, the Texas Instruments INA141 features input protection to ±40 V. This rating makes the device suitable for systems where sensor wiring may experience overload or transient conditions. Protected inputs do not mean every input condition is safe for normal operation, so engineers should confirm signal limits, supply state, current paths, and external protection requirements against the complete manufacturer electrical characteristics.
Does INA141UA/2K5 require a heatsink at high temperature?
The INA141UA/2K5 is a low-power 8-pin SOIC instrumentation amplifier, and its specified operating range extends to +85°C. Whether a heatsink is necessary depends on supply voltage, load, output amplitude, power dissipation, ambient temperature, and board thermal resistance. Estimate worst-case dissipation from the actual operating condition and compare it with the package thermal limits in the manufacturer datasheet.
What is the bandwidth of INA141UA/2K5 at gain 100?
The INA141UA/2K5 provides 200 kHz bandwidth at a gain of 100 V/V. Texas Instruments attributes this performance to current-feedback input circuitry, which maintains useful bandwidth at high closed-loop gain. The 8-pin SOIC package is consequently suitable for measurement loops that need more bandwidth than a conventional unity-gain instrumentation-amplifier architecture may provide.
Where can I buy INA141UA/2K5 and check its lead time?
Use the Request a Quote form on this page to request INA141UA/2K5 pricing, stock confirmation, and current lead time from XAIPART. The exact INA141UA/2K5 is listed by the manufacturer in an 8-pin SOIC (D) package, and distributor search results identify the same instrumentation-amplifier ordering code. Current commercial availability should always be confirmed at the time of quotation.
How do I design the input network for INA141UA/2K5?
Use balanced source impedances and route the differential input pair as a closely matched, short pair on the PCB. Keep the reference node low-impedance and away from switching nodes, while placing supply bypass capacitors close to the SOIC supply pins. Because the gain is fixed by the selected configuration, verify that the full sensor range remains inside both the input common-mode range and output swing.
Is INA141UA/2K5 RoHS and REACH compliant?
The INA141UA/2K5 is an 8-pin SOIC instrumentation amplifier from Texas Instruments, but its individual RoHS and REACH declarations should be confirmed against the manufacturer product documentation for the exact ordering code. Do not infer compliance from the package or family name. A related distributor catalog entry identifies the INA141UA/2K5E4 as EU RoHS compliant and REACH compliant, while the exact suffix-level declarations should still be checked.

के लिए इंजीनियरिंग संदर्भ डेटा INA141UA/2K5 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose INA141UA/2K5 when the design requires the exact active Texas Instruments ordering code, selectable 10 V/V or 100 V/V gain, 200 kHz bandwidth at gain 100, and protected inputs rated to ±40 V. Choose INA141UA when its suffix-specific gain configuration and availability better fit the BOM, but verify the schematic pins and ordering meaning before substitution. INA141U is a closely related 8-SOIC part with matching basic supply, offset, and minimum-gain information, but its exact suffix behavior still requires review. Avoid INA141UA/2K5G4 for new production because it is identified as obsolete. INA131AP and INA131BP use the same 8-pin package but belong to a different gain-setting architecture, making them lower-confidence drop-ins unless the existing board uses the corresponding INA131 feedback configuration.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद INA141UA INA141U INA141UA/2K5G4 INA141UA/2K5E4 INA131AP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC (D)
Product Family INA141 INA141 INA141 INA141 INA141 INA131
Number of Channels 1 channel 1 channel 1 channel 1 channel 1 channel 1 channel
Gain 10 V/V or 100 V/V 10 V/V or 100 V/V 10 V/V minimum 10 V/V or 100 V/V family configuration 10 V/V or 100 V/V family configuration 10 V/V minimum

मुख्य विशेषताएँ

  • Exact active INA141UA/2K5 ordering configuration (बनामINA141UA/2K5G4)
  • 200 kHz bandwidth at the maximum 100 V/V gain (बनामINA131AP)
  • Minimum common-mode rejection of 117 dB (बनामINA141UA)
  • Input protection to ±40 V (बनामINA141U)

डिज़ाइन नोट्स

Place the INA141UA/2K5 close to the sensor or bridge output, and route the two differential inputs as a short, closely spaced pair. Keep the reference connection and analog ground return away from switching-converter and digital-clock nodes. Place supply bypass capacitors directly beside the relevant SOIC supply pins, with a short ground return. Symmetrical routing is important because mismatched input impedances and trace leakage can reduce the practical common-mode rejection achieved in a finished board.

Do not select a gain solely from the sensor's nominal sensitivity. First confirm the full differential signal range, common-mode voltage, output swing, supply voltage, and allowed error. The INA141UA/2K5 supports 10 V/V and 100 V/V, but either setting can clip if the amplifier lacks sufficient output headroom. Also verify the exact gain-code behavior for the ordered suffix instead of assuming that every related INA141 ordering code uses identical gain-selection logic.

For the fastest measurements, use very low source impedances and keep input-node capacitance balanced. The 200 kHz bandwidth at gain 100 supports useful acquisition speed, but the complete signal chain must also settle within the ADC sample window. Use a suitable low-impedance reference, maintain return paths continuous during cable or connector transitions, and evaluate gain error and settling with the actual sensor rather than relying only on the amplifier's headline bandwidth.

Estimate power dissipation using the actual positive and negative supply currents, supply voltage, and output operating point across the required -40°C to +85°C ambient range. The 8-pin SOIC package has limited copper area compared with exposed-pad options, so airflow, board copper, and nearby heat sources matter. Do not infer thermal margin from the low-power description alone; use the manufacturer power dissipation and thermal resistance tables for the final worst-case assessment.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

A related Abacus Technologies catalog entry identifies INA141UA/2K5E4 as EU RoHS compliant, REACH compliant, and DRC Conflict Free. Exact suffix-level declarations for INA141UA/2K5 were not established, so the individual fields remain unknown.

डेटा सत्यापन तिथि: 2026-11-19 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

INA141UA/2K5 datasheet INA141UA/2K5 pinout INA141UA/2K5 datasheet pdf INA141UA/2K5 equivalent INA141UA/2K5 replacement INA141UA/2K5 cross reference INA141UA vs INA141U INA141UA/2K5 price INA141UA/2K5 stock Texas Instruments INA141UA/2K5 INA141UA/2K5 200kHz INA141UA/2K5 SOIC-8

संबंधित कंपोनेंट्स और शब्द

Texas Instruments INA141UA/2K5 INA141UA INA141U INA141UA/2K5G4 INA141UA/2K5E4 INA131AP INA131BP instrumentation amplifier differential amplifier analog amplifier integrated circuit precision low-power amplifier three-op-amp architecture current-feedback input selectable gain common-mode rejection ratio CMRR input offset voltage input bias current input protection 8-pin SOIC surface-mount package Wheatstone bridge load cell RoHS REACH
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें