Texas Instruments

INA2128UG4 - Dual Instrumentation Amplifier | Texas Instruments

MPN: INA2128UG4 ✓ सक्रिय
16-pin SOIC Package
न्यूनतम ऑर्डर मात्रा: 1 |

INA2128UG4 अवलोकन

The Texas Instruments INA2128UG4 is a dual, low-power instrumentation amplifier with two independent amplifier channels, gain settings from 1 to 10,000, and bandwidth of 200 kHz at a gain of 100. The device is packaged in a 16-pin SOIC and is specified for operation from -40°C to +85°C.

An instrumentation amplifier is a precision analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting common-mode signals. Its internal three-op-amp architecture provides a practical combination of high input impedance, accurate differential gain, and common-mode rejection. This places the INA2128UG4 in the hierarchy of instrumentation amplifier, analog signal conditioner, amplifier IC, and semiconductor.

The principal features include a dual-channel configuration, low-power operation, user-programmable gain from 1 to 10,000 using one external resistor, and current-feedback input circuitry that maintains useful bandwidth at high gain. These characteristics suit sensor outputs, bridge-based measurements, biomedical instrumentation, and analog signal chains where small differential signals must be measured accurately in the presence of larger common-mode voltages.

The three-op-amp topology separates differential input handling from the gain-setting network, helping simplify circuit design and reduce external component count. A single gain resistor establishes the selected gain, while internal input and feedback stages provide the required signal amplification. The result is a versatile general-purpose instrumentation amplifier that can serve both precision measurement and general instrumentation applications.

Typical uses include pressure and temperature sensor interfaces, strain-gauge and Wheatstone bridge excitation, biomedical signal acquisition, current-shunt measurement, laboratory instrumentation, and low-level analog front ends. The dual architecture allows two independent sensor channels in one package, reducing board area when both channels are required.

Designers should place the gain-setting resistor close to the gain pins, observe the input and output common-mode limits, and decouple the supply pins according to the manufacturer datasheet. Input and output filtering should be selected for the required bandwidth because excessive capacitance can affect stability and phase margin. The operating temperature range also requires thermal verification for the complete board assembly.

This product page combines the INA2128UG4 device identity, package and gain details with practical application guidance, same-family alternatives, and a parameter-focused comparison. It is designed to help engineers locate the datasheet, verify pin compatibility, understand bandwidth constraints, and plan an instrumentation front end before requesting a quote.

के लिए ड्रॉप-इन विकल्प INA2128UG4 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं INA2128UG4 (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Architecture, Input Circuitry.

Texas Instruments
Architecture: Three-op-amp instrumentation-amplifier design
Input Circuitry: Current-feedback
इसके साथ तुलना करें INA2128UG4 →

INA2128U

✅ ड्रॉप-इन
Texas Instruments
📦 16-pin SOIC
Dual instrumentation amplifier · Three-op-amp instrumentation-amplifier design · 2 channels · 1 to 10,000 · 1 external resistor · 200 kHz · Current-feedback · Single-ended and differential

कीमत के लिए संपर्क करें

डेटाशीट देखें →

INA2128U/1KE4

✅ ड्रॉप-इन
📦 16-pin SOIC
Same INA2128 dual-channel topology and 16-pin SOIC footprint; accuracy and ordering designation differ, while the family supports gain from 1 to 10,000 and 200 kHz bandwidth at gain 100.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

INA2128U1G4

✅ ड्रॉप-इन
📦 16-pin SOIC
Same INA2128 dual-channel family in a 16-pin SOIC; ordering and qualification designation differ, with no change stated to the 1 to 10,000 gain range or 200 kHz bandwidth at gain 100.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

INA2128UG4 Maximum Ratings और Electrical Characteristics

Product Type Dual instrumentation amplifier
Architecture Three-op-amp design
Number of Amplifier Channels 2 channels
Gain Range 1 to 10,000
Gain Setting Method 1 external resistor
Bandwidth at Gain 100 200 kHz
Input Circuitry Current feedback
ऑपरेटिंग तापमान रेंज -40°C to +85°C
पैकेज 16-pin SOIC
माउंटिंग प्रकार Surface mount

INA2128UG4 16-pin soic पिन कॉन्फ़िगरेशन गाइड

INA2128UG4 (16-pin soic पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।

INA2128UG4 के लिए 16-pin soic पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: INA2128UG4.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

INA2128UG4 के लिए उपयुक्त है 6 अनुप्रयोगs: Bridge Sensor Measurement, Medical Signal Acquisition, Current-Shunt Monitoring, Industrial Sensor Interface, Test and Measurement Instrumentation, Audio and Analog Signal Conditioning.

🏭

Bridge Sensor Measurement

The INA2128UG4 is well suited to strain-gauge, pressure, and other bridge-based sensors because its differential input arrangement measures the small bridge imbalance while rejecting the larger common-mode voltage. A single external resistor per channel sets the gain from 1 to 10,000, allowing the circuit to amplify a millivolt-level sensor output to a usable ADC input range. The current-feedback architecture retains 200 kHz bandwidth at gain 100, which supports dynamic measurements better than a narrow-band fixed-gain amplifier. The main design consideration is common-mode and output-range verification across the full bridge excitation and sensor tolerance.

💊

Medical Signal Acquisition

The INA2128UG4 can serve as the analog front end for low-level biomedical sensor signals when two isolated or related channels are required. Its instrumentation-amplifier architecture provides differential measurement and common-mode rejection, while the programmable 1-to-10,000 gain range allows one device family to cover multiple sensor amplitudes. At gain 100, the manufacturer specifies 200 kHz bandwidth, providing adequate margin for many physiological waveforms without requiring an extremely high-speed amplifier. Designers should verify input bias current, offset, noise, and the medical system's applicable safety requirements separately.

⚡

Current-Shunt Monitoring

The INA2128UG4 is appropriate for measuring the differential voltage developed across a low-value current shunt. The amplifier converts the millivolt-scale shunt signal into a voltage suitable for an ADC, while its differential topology reduces disturbance from the supply rail and other shared signals. Two independent channels allow simultaneous measurement of a source and a reference load or two power rails. With gain adjustable from 1 to 10,000 and bandwidth of 200 kHz at gain 100, the device supports both slow power measurements and higher-bandwidth control loops when the complete signal chain permits.

🏭

Industrial Sensor Interface

The INA2128UG4 fits industrial sensor interfaces that combine a small differential signal with a substantially larger common-mode voltage. Its two channels reduce board area when monitoring two sensors, and the single-resistor gain setting simplifies calibration across different measurement ranges. The 200 kHz bandwidth at gain 100 allows the amplifier to preserve useful response for faster process-control signals while offering gains up to 10,000 for precision measurements. Layout should keep the gain resistor and feedback routing compact, and the completed circuit should be checked for supply variation, grounding, and common-mode excursions.

🔧

Test and Measurement Instrumentation

The INA2128UG4 is useful in laboratory and production-test front ends that measure small differential signals over a wide gain range. Its dual architecture can monitor two related nodes without duplicating the instrumentation amplifier, while the selectable 1-to-10,000 gain lets the same design cover low-level sensor outputs and larger differential test signals. Current-feedback input circuitry provides 200 kHz bandwidth at gain 100, making the device suitable for many bandwidth-oriented measurement setups. Gain accuracy, resistor tolerance, input noise, settling behavior, and output saturation must be evaluated against the measurement bandwidth and required uncertainty.

🎧

Audio and Analog Signal Conditioning

The INA2128UG4 can condition balanced or differential low-level audio signals where common-mode rejection and adjustable gain are important. The instrumentation-amplifier configuration accepts a differential source and provides a single-ended conditioned output, while two channels can process stereo or complementary signals. The 200 kHz bandwidth at gain 100 covers the full range of many audio-band applications, although the maximum gain of 10,000 should not be selected merely for headroom because bandwidth and noise performance change with gain. The design should include appropriate input filtering, grounding, and output-headroom checks.

अनुशंसित उत्पादों का सारांश

INA2128U Texas Instruments उपयोग में: Bridge Sensor Measurement, Medical Signal Acquisition, Current-Shunt Monitoring, Industrial Sensor Interface, Test and Measurement Instrumentation INA2128U/1KE4 Same-family alternate ordering option उपयोग में: Bridge Sensor Measurement, Current-Shunt Monitoring, Industrial Sensor Interface, Audio and Analog Signal Conditioning INA2128U1G4 Same-family dual instrumentation amplifier उपयोग में: Medical Signal Acquisition, Test and Measurement Instrumentation, Audio and Analog Signal Conditioning
What is the INA2128UG4?
The INA2128UG4 is a dual, low-power, general-purpose instrumentation amplifier manufactured by Texas Instruments. According to the manufacturer datasheet, each channel uses a three-op-amp architecture, supports gain from 1 to 10,000 with one external resistor, and maintains 200 kHz bandwidth at a gain of 100. The device is offered in a 16-pin SOIC package.
What are the key specifications of INA2128UG4 that engineers should know?
The INA2128UG4 provides two instrumentation-amplifier channels, a gain range of 1 to 10,000, and 200 kHz bandwidth at gain 100. According to the Texas Instruments manufacturer datasheet, it uses a three-op-amp design with current-feedback input circuitry and is specified from -40°C to +85°C. It is packaged in a 16-pin SOIC for surface-mount assembly.
How do I set the gain of an INA2128UG4 channel?
The INA2128UG4 sets each channel's gain with one external resistor connected to the gain-setting network. According to the manufacturer datasheet, the supported gain range is 1 to 10,000. The resistor value should be selected from the gain equation in the datasheet and placed close to the corresponding gain pins to reduce parasitic resistance and signal pickup.
Where can I download the INA2128UG4 datasheet PDF?
The official INA2128UG4 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ina2128.pdf. It contains the complete pin descriptions, gain equations, electrical characteristics, application circuit, and ordering information. Use the manufacturer document for PCB design, resistor selection, supply limits, and channel-specific pin assignments.
Where can I find the INA2128UG4 pinout?
The INA2128UG4 pinout is shown in the Texas Instruments INA2128 manufacturer datasheet, which identifies the connections for both amplifier channels, gain resistors, supply rails, and grounding. The device uses a 16-pin SOIC package. Assign PCB tracks from the pin-description table and preserve the package pin numbering shown in the mechanical drawing.
Is the INA2128UG4 suitable for high-gain sensor measurement?
The INA2128UG4 is suitable for high-gain differential measurements because its current-feedback input circuitry provides 200 kHz bandwidth even at gain 100. According to the Texas Instruments datasheet, the gain range extends to 10,000. At the highest gains, bandwidth is naturally lower, so sensor bandwidth, noise, settling time, and resistor tolerances must be evaluated together.
Where can I buy the INA2128UG4 online?
Use the Request a Quote form on this page to request the INA2128UG4 from XAIPART. The form is the appropriate route for current commercial availability, order quantities, and delivery scheduling. The exact Texas Instruments ordering code is INA2128UG4, and the component is supplied in a 16-pin SOIC package.
What is the price of the INA2128UG4?
Request a current quote for the INA2128UG4 using the Request a Quote form on this page. Commercial pricing can depend on order quantity, current inventory, packaging, and market conditions, so a static figure would not remain current. The form allows the requested quantity and application requirements to be included with the inquiry.
What is the lead time for the INA2128UG4?
The current lead time for the INA2128UG4 should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, production status, and replenishment conditions. When requesting a quote, specify the required quantity, target delivery date, and whether the 16-pin SOIC shipping configuration is acceptable.
Is the INA2128UG4 in stock?
Use the Request a Quote form on this page to check current availability and stock allocation for the INA2128UG4. The requested quantity should be included in the inquiry so the supplier can confirm the appropriate supply position. Because inventory changes, this page does not present a potentially misleading fixed stock status.
What can replace the INA2128UG4?
The closest documented same-family alternatives are the INA2128U, INA2128U/1KE4, and INA2128U1G4, all associated with the Texas Instruments INA2128 family and 16-pin SOIC packaging. Verify the exact gain, accuracy grade, supply limits, and lifecycle status against the manufacturer datasheet before substitution. A footprint match alone does not confirm complete electrical equivalence.
Is the INA2128U a drop-in replacement for the INA2128UG4?
The INA2128U is a same-family INA2128 ordering option in the 16-pin SOIC package and is the most direct candidate for a drop-in review. According to the TI product information, the INA2128 family provides dual low-power instrumentation-amplifier channels with gain from 1 to 10,000 and 200 kHz bandwidth at gain 100. Confirm ordering suffix, accuracy grade, and temperature coverage before production use.
When should I choose the INA2128UG4 instead of the INA2128U?
Choose the INA2128UG4 when its exact ordering suffix, qualification, and sourcing conditions match the intended design. Choose the INA2128U when it provides the required electrical grade and package at a different ordering configuration. Both belong to the same dual, low-power INA2128 instrumentation-amplifier family, so the decision should focus on ordering details rather than basic functionality.
INA2128UG4 vs INA2128U/1KE4 — which is better for an industrial sensor interface?
The INA2128UG4 and INA2128U/1KE4 are both Texas Instruments INA2128-family dual instrumentation amplifiers in 16-pin SOIC packages. The family-level distinction includes gain range of 1 to 10,000 and 200 kHz bandwidth at gain 100. For an industrial interface, compare the ordering suffix, temperature grade, accuracy grade, supply range, and availability using each part's manufacturer documentation before selecting one.
What is the difference between INA2128UG4 and INA2128U?
The INA2128UG4 and INA2128U are ordering variants within the same Texas Instruments INA2128 family. Both are dual, low-power instrumentation amplifiers using a three-op-amp architecture, with gain from 1 to 10,000 and 200 kHz bandwidth at gain 100. The exact differences should be checked by ordering suffix and qualification marking in the manufacturer's part details before treating either as a replacement.
Is there a cross-brand drop-in equivalent for the INA2128UG4?
No cross-brand drop-in equivalent was established from the available cross-reference results, so none is listed as a drop-in alternative. The documented candidates are Texas Instruments members of the same INA2128 family. A valid cross-brand replacement would require an identical 16-pin SOIC footprint, compatible pin functions, and closely matched gain, bandwidth, supply, accuracy, and common-mode performance.

के लिए इंजीनियरिंग संदर्भ डेटा INA2128UG4 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the INA2128UG4 for new dual-channel analog front ends that need differential measurement, common-mode rejection, and programmable gain from 1 to 10,000. Its 200 kHz bandwidth at gain 100 makes it appropriate for many sensor, bridge, shunt, audio, and test applications, while the 16-pin SOIC package supports compact surface-mount layouts. Consider the INA2128U when its ordering and qualification details better match production requirements. Evaluate INA2128U/1KE4 when its specified accuracy or ordering grade is preferable, and INA2128U1G4 when that ordering designation is supported by the required supply and qualification plan. All listed alternatives share the same basic INA2128 family architecture and package. Before substitution, verify the exact ordering suffix, temperature coverage, gain accuracy, offset, supply range, input and output limits, bandwidth at the selected gain, and lifecycle status. If none of the same-family options matches the required electrical grade, do not assume a cross-brand device is drop-in compatible.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद INA2128U INA2128U/1KE4 INA2128U1G4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC
Product Type Dual low-power instrumentation amplifier Dual low-power instrumentation amplifier Dual low-power instrumentation amplifier Dual low-power instrumentation amplifier
Architecture Three-op-amp design Three-op-amp design Three-op-amp design Three-op-amp design
Amplifier Channels 2 channels 2 channels 2 channels 2 channels
Gain Range 1 to 10,000 1 to 10,000 1 to 10,000 1 to 10,000
Bandwidth at Gain 100 200 kHz 200 kHz 200 kHz 200 kHz
Gain Setting 1 external resistor 1 external resistor 1 external resistor 1 external resistor
Input Circuitry Current feedback Current feedback Current feedback Current feedback

मुख्य विशेषताएँ

  • Dual-channel integration in one package (बनामINA2128U)
  • Programmable gain spans four decades (बनामINA2128U/1KE4)
  • Useful bandwidth at high gain (बनामINA2128U1G4)
  • Compact surface-mount implementation (बनामINA2128U)

डिज़ाइन नोट्स

Place each gain-setting resistor close to the corresponding INA2128UG4 gain pins and keep the input traces short and symmetric. Current-feedback input circuitry can be sensitive to parasitic capacitance and unequal trace lengths, particularly at high gain. Route input and feedback connections away from switching nodes and keep the ground return beneath the analog signal path to reduce pickup and ground-potential errors.

Do not assume that every INA2128 ordering suffix is interchangeable without checking accuracy grade, qualification, and temperature coverage. Compare the exact ordering table for the INA2128UG4, INA2128U, INA2128U/1KE4, and INA2128U1G4. Also verify that the selected gain keeps both inputs and the output inside their common-mode and output-swing limits under minimum supply, maximum load, and worst-case sensor voltage.

Choose input filtering only after accounting for the 200 kHz bandwidth specified at gain 100. A low-pass filter with a corner too close to the required signal bandwidth can create phase error, while excessive input capacitance may alter stability or bandwidth. Evaluate the complete gain, noise, settling-time, and filter behavior rather than evaluating the gain resistor and input network independently.

Decouple each supply rail close to the device and follow the capacitor values and layout shown in the manufacturer datasheet. The INA2128UG4 is a dual low-power instrumentation amplifier, but its total supply demand and any nearby precision converter or reference can still introduce local noise. Keep sensitive gain and feedback nodes away from regulator switching loops and ensure the power source has adequate transient response during startup and load changes.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified for this ordering code. Confirm compliance using the manufacturer's current product documentation.

डेटा सत्यापन तिथि: 2026-11-14 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

INA2128UG4 datasheet INA2128UG4 pinout INA2128UG4 datasheet pdf INA2128UG4 equivalent INA2128UG4 replacement INA2128UG4 cross reference INA2128UG4 vs INA2128U INA2128UG4 footprint INA2128UG4 application circuit INA2128UG4 price INA2128UG4 stock Texas Instruments INA2128UG4

संबंधित कंपोनेंट्स और शब्द

Texas Instruments INA2128UG4 INA2128U INA2128U/1KE4 INA2128U1G4 dual instrumentation amplifier instrumentation amplifier analog signal conditioner amplifier IC semiconductor three-op-amp architecture current-feedback input programmable gain common-mode rejection differential signal gain-setting resistor 200 kHz bandwidth bridge sensor strain gauge current-shunt monitoring biomedical signal acquisition industrial sensor interface 16-pin SOIC SOIC family surface mount
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें