Renesas Electronics

ISL84523IV - 4-Channel SPST Analog Switch | Renesas Electronics

MPN: ISL84523IV ✗ जीवन की समाप्ति
+2 V to +12 V Vdss 1 nA Id 100 ohm Rds(on) 16-pin TSSOP Package
न्यूनतम ऑर्डर मात्रा: 1 |

ISL84523IV अवलोकन

Renesas Electronics ISL84523IV is a low-voltage CMOS quad analog switch with four independently controlled SPST channels, 100 ohm maximum on-resistance, and a 16-pin TSSOP package. It operates from a single +2 V to +12 V supply or from a split ±2 V to ±6 V supply, making it suitable for low-voltage signal routing in battery-powered and precision test systems.

An analog switch is a semiconductor interface device that connects or isolates analog signals under digital control. Its function in the broader hierarchy is analog switch → multiplexer or demultiplexer → interface IC. The ISL84523IV uses four separate SPST paths rather than a shared multiplexer bus, allowing four signals to be routed independently while keeping the control logic separate from the analog nodes.

Key characteristics include a maximum on-resistance of 100 ohm, on-resistance matching between channels of 1 ohm, low power consumption below 1 microwatt, and maximum leakage current of 1 nA in the principal operating description. Switching times are listed as 45 ns on and 15 ns off. The manufacturer also identifies TTL and CMOS control compatibility, a minimum 2000 V ESD protection rating using Method 3015.7, and break-before-make timing of at least 2000 ns.

The ISL84523IV family is designed for precision low-voltage signal switching. Separate control inputs permit each SPST switch to be commanded independently, while low leakage and low power consumption help preserve small signals in battery-operated measurement equipment. Its stated pin compatibility with DG411, DG412, and DG413 devices supports reuse of existing routed analog-switch layouts when control behavior and application requirements are compatible.

Typical uses include battery-powered test equipment, automated measurement systems, signal-isolation networks, sample-and-hold circuitry, and low-voltage analog front ends. The device is also identified as a drop-in replacement for MAX4521, MAX4522, and MAX4523 devices. Because it supports both single-supply and dual-supply operation, it can address dual-rail instrumentation as well as systems whose analog signals remain above ground.

For new layouts, route each analog switch terminal to the intended signal path and keep control traces away from sensitive analog nodes. Confirm the complete pin map and control truth table in the manufacturer datasheet before making substitutions. The 16-pin TSSOP footprint supports compact density, but exposed copper and careful grounding remain important for preserving low-level signal integrity.

This page combines the manufacturer’s electrical and switching characteristics with practical routing guidance, drop-in cross-reference options, and a parameter-by-package comparison. It is intended to help engineers identify whether the ISL84523IV fits the required voltage range, control interface, switching behavior, and board footprint before requesting a quote.

के लिए ड्रॉप-इन विकल्प ISL84523IV — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं ISL84523IV (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Switch Configuration, Analog Signal Range, On-Resistance (rDS on), Power Dissipation.

Analog Devices
Package: 16-SOIC
Switch Configuration: 4 x SPST (normally open)
इसके साथ तुलना करें ISL84523IV →
Analog Devices
Package: SOIC-16 (16-SOIC)
Switch Configuration: 4 independent 1:1 SPST
Analog Signal Range: +/-15 V
इसके साथ तुलना करें ISL84523IV →
Analog Devices
Package: SOIC-16 (DY suffix)
Switch Configuration: Quad SPST (2 NC + 2 NO)
Analog Signal Range: 15 V (within rails), up to 40 Vp-p with 44 V process
इसके साथ तुलना करें ISL84523IV →

MAX4521

✅ ड्रॉप-इन
📦 16-TSSOP
Drop-in replacement with the same 100 ohm maximum on-resistance rating; control-channel configuration must match the selected application

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

MAX4522

✅ ड्रॉप-इन
📦 16-TSSOP
Drop-in replacement with the same 100 ohm maximum on-resistance rating; control-channel configuration must match the selected application

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

MAX4523

✅ ड्रॉप-इन
📦 16-TSSOP
Drop-in replacement with the same 100 ohm maximum on-resistance rating; control-channel configuration must match the selected application

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

DG411

✅ ड्रॉप-इन
Analog Devices
📦 16-TSSOP
4 x SPST (normally open) · 35 ohm · 3 ohm · 4 ohm · Single-ended up to 44V, or split +/-20V · 40VP-P signals · TTL and CMOS · Bilateral (conducts equally in either direction)

कीमत के लिए संपर्क करें

डेटाशीट देखें →

DG412

✅ ड्रॉप-इन
Analog Devices
📦 16-TSSOP
Quad SPST Analog Switch (4 x NO) · 4 independent 1:1 SPST · 45 ohm max (ADI/Maxim); 35 ohm (Vishay/Renesas grade) · 3 ohm max (redesigned Maxim version) · 4 ohm max over signal range · 110 ns (typ., family datasheet) · +/-15 V · 44 V

कीमत के लिए संपर्क करें

डेटाशीट देखें →

DG413

✅ ड्रॉप-इन
Analog Devices
📦 16-TSSOP
Quad SPST (2 NC + 2 NO) · 35 ohm max · 150 ns max · 100 ns max · 44 V · +10 V to +30 V · ±4.5 V to ±20 V · 15 V (within rails), up to 40 Vp-p with 44 V process

कीमत के लिए संपर्क करें

डेटाशीट देखें →

ISL84523IV Maximum Ratings और Electrical Characteristics

Number of Switches 4
Switch Configuration 4 × SPST
Multiplexer Ratio 1:1
Maximum On-Resistance 100 ohm
On-Resistance Matching Between Channels 1 ohm
Single-Supply Voltage Range +2 V to +12 V
Dual-Supply Voltage Range ±2 V to ±6 V
Power Consumption <1 microwatt
Maximum Leakage Current 1 nA
Turn-On Time 45 ns
Turn-Off Time 15 ns
Break-Before-Make Timing 2000 ns minimum
ESD Protection 2000 V minimum, Method 3015.7
Control Logic Compatibility TTL and CMOS compatible
पैकेज 16-pin TSSOP
Process Technology CMOS

ISL84523IV 16-pin tssop पिन कॉन्फ़िगरेशन गाइड

ISL84523IV (16-pin tssop पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।

ISL84523IV के लिए 16-pin tssop पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: ISL84523IV.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

ISL84523IV के लिए उपयुक्त है 6 अनुप्रयोगs: Battery-Powered Test Equipment, Automated Measurement Systems, Precision Analog Signal Isolation, Sample-and-Hold Signal Routing, Dual-Rail Instrumentation, Low-Voltage Sensor Interfacing.

🧩

Battery-Powered Test Equipment

The ISL84523IV fits low-voltage battery-powered test equipment because the manufacturer specifies power consumption below 1 microwatt and leakage current up to 1 nA. Its four independent SPST channels can isolate sensor, reference, and control paths without requiring a shared multiplexer bus. A single +2 V to +12 V supply supports portable instrumentation, while TTL-compatible control inputs allow direct interfacing with common digital controllers. The 100 ohm maximum on-resistance should be included in the input and output impedance budget when switching high-impedance sensors.

⚡

Automated Measurement Systems

The ISL84523IV is suitable for automated measurement systems that route several precision signals through a common analog front end. Four separately controlled SPST paths provide isolation between measurement channels, while 45 ns turn-on and 15 ns turn-off times support rapid sequencing. The specified 100 ohm maximum on-resistance and 1 ohm channel matching help minimize path-dependent amplitude errors. For dual-rail instruments, the ±2 V to ±6 V operating range supports bipolar signals, provided every analog and control voltage remains within the manufacturer limits.

📡

Precision Analog Signal Isolation

The ISL84523IV can isolate precision analog nodes in instrumentation front ends where leakage and path consistency are important. The manufacturer specifies maximum leakage current of 1 nA and on-resistance matching between channels of 1 ohm, helping reduce errors introduced by unused connected paths. Four SPST channels allow a controller to connect or disconnect multiple sensitive nodes independently. Because the switch contributes up to 100 ohm on-resistance, source and receiver impedances should be considered when defining accuracy and settling requirements.

📺

Sample-and-Hold Signal Routing

The ISL84523IV works in sample-and-hold signal-routing networks where acquisition paths must be connected quickly and isolated from inactive channels. Its 45 ns turn-on and 15 ns turn-off characteristics provide fast control response, while break-before-make timing of at least 2000 ns helps prevent overlap during state changes. The 16-pin TSSOP package allows placement close to the sampling node, reducing trace length. Designers should still account for switch on-resistance, charge injection, and settling behavior in the complete acquisition chain.

🏭

Dual-Rail Instrumentation

The ISL84523IV is appropriate for dual-rail instrumentation that must route signals around ground. Its split-supply operating range of ±2 V to ±6 V accommodates common ±5 V analog systems, while TTL and CMOS control compatibility supports conventional digital control hardware. Four independent SPST switches can route positive, negative, or reference signals without sharing a common internal bus. The analog signal amplitude and control thresholds must be checked against the datasheet for the exact supply configuration to prevent overstress during transitions.

🧩

Low-Voltage Sensor Interfacing

The ISL84523IV can route signals from low-voltage sensors where leakage and power use are critical. Its 1 nA maximum leakage specification and sub-1-microwatt power consumption help limit disturbance to high-impedance sensing circuits, while four independent channels support multiplexing between sensor, excitation, and reference paths. The maximum 100 ohm on-resistance may be significant with very high source impedances and should be included in the signal-chain error budget. Place the device near the sensor interface and keep control traces separated from sensitive analog nets.

अनुशंसित उत्पादों का सारांश

DG411 Analog Devices उपयोग में: Battery-Powered Test Equipment, Precision Analog Signal Isolation, Sample-and-Hold Signal Routing DG412 Analog Devices उपयोग में: Battery-Powered Test Equipment, Dual-Rail Instrumentation MAX4521 Drop-in quad SPST switch alternative उपयोग में: Automated Measurement Systems, Sample-and-Hold Signal Routing MAX4522 Drop-in quad SPST switch alternative उपयोग में: Automated Measurement Systems, Dual-Rail Instrumentation MAX4523 Drop-in quad SPST switch alternative उपयोग में: Automated Measurement Systems, Low-Voltage Sensor Interfacing DG413 Analog Devices उपयोग में: Precision Analog Signal Isolation, Low-Voltage Sensor Interfacing
What is the ISL84523IV?
The ISL84523IV is a low-voltage CMOS quad analog switch with four independently controlled SPST channels in a 16-pin TSSOP package. According to the Renesas Electronics product page, it operates from a single +2 V to +12 V supply or a split ±2 V to ±6 V supply, with a maximum on-resistance of 100 ohm and separate control inputs for each channel.
What is the maximum on-resistance of the ISL84523IV?
The ISL84523IV has a maximum on-resistance of 100 ohm, and its on-resistance matching between channels is specified at 1 ohm. According to the Renesas Electronics product page, these characteristics make the device suitable for routing low-voltage analog signals where consistent channel resistance helps limit signal-level variation between switched paths.
Where can I download the ISL84523IV datasheet PDF?
The official ISL84523IV datasheet and product resources are available through the Renesas Electronics part-details page. Open the linked manufacturer page and select the ISL84523 datasheet resource for the complete pin configuration, supply limits, electrical characteristics, control truth table, timing information, and package drawings.
Where can I find the ISL84523IV pinout?
The ISL84523IV pinout is documented in the manufacturer’s ISL84523 datasheet and its 16-pin TSSOP package drawing. Use the pin-description table and standard counter-clockwise numbering shown in that document when assigning PCB tracks, especially because the four analog switch channels have separate control inputs and analog terminals.
What supply voltages does the ISL84523IV accept?
The ISL84523IV accepts either a single +2 V to +12 V supply or a dual ±2 V to ±6 V supply. According to the Renesas Electronics product page, this flexibility supports both single-rail portable equipment and split-rail analog systems. The selected operating mode must remain within the limits and polarity conditions stated in the manufacturer datasheet.
How fast is the ISL84523IV?
The ISL84523IV has a listed turn-on time of 45 ns and turn-off time of 15 ns. According to the Renesas Electronics product page, break-before-make timing is at least 2000 ns. These values should be compared with the source impedance, receiver bandwidth, and required settling interval of the analog path rather than treated as a complete system switching-time specification.
Is the ISL84523IV suitable for battery-powered equipment?
Yes, the ISL84523IV is suitable for battery-powered equipment because the manufacturer identifies low power consumption below 1 microwatt and low leakage current up to 1 nA as core benefits. These characteristics can help reduce switching-related loading while preserving low-level signals, although total system power depends on the control logic and connected circuitry.
What can replace the ISL84523IV?
The ISL84523IV can be replaced by the MAX4521, MAX4522, MAX4523, DG411, DG412, or DG413 devices where their control logic, electrical limits, and channel behavior match the design. The Renesas Electronics product page specifically identifies the MAX4521 through MAX4523 devices as drop-in replacements and states that the ISL84523 family is pin compatible with DG411, DG412, and DG413 devices.
Is the ISL84523IV the same as the MAX4523?
The ISL84523IV and MAX4523 are identified as drop-in-compatible devices, but their internal control behavior must still be checked against the selected channel implementation. The Renesas Electronics product page lists MAX4521 through MAX4523 as drop-in replacements for the ISL84523 family and gives a maximum on-resistance of 100 ohm, 1 ohm channel matching, and TTL/CMOS compatibility.
What is the best Renesas Electronics equivalent for the ISL84523IV?
The closest same-manufacturer option is another qualified ordering code within the ISL84523 family, subject to matching the required control configuration and temperature grade. The manufacturer identifies MAX4521, MAX4522, and MAX4523 as drop-in replacements and confirms compatibility with DG411, DG412, and DG413 layouts; verify the exact pin behavior in the datasheet before approving a substitution.
When should I choose the ISL84523IV over a DG411 or DG413?
Choose the ISL84523IV when its independent SPST control scheme and specified low-voltage performance meet the design requirements and you want a Renesas-supported option for an existing compatible layout. The manufacturer states pin compatibility with DG411, DG412, and DG413, but control truth-table, supply, switching-time, and electrical-limit differences still require verification before replacement.
Is the ISL84523IV suitable for a ±5 V analog measurement system?
Yes, the ISL84523IV is suitable for a ±5 V system because its documented dual-supply operating range extends to ±6 V. According to the Renesas Electronics product page, the device also supports low-voltage single-supply operation. Signal levels, control thresholds, leakage, and absolute maximum ratings must remain within the datasheet limits for the selected rail arrangement.
How should I design the PCB around the ISL84523IV?
Place the ISL84523IV close to the analog paths it switches, keep switching-node traces away from high-impedance inputs, and provide a low-impedance ground reference. Route control traces to minimize coupling into adjacent analog nets, especially when the switch handles signals near the low end of the 100 ohm on-resistance range.
Does the ISL84523IV support TTL and CMOS control signals?
Yes, the ISL84523IV supports TTL and CMOS-compatible control signals. According to the Renesas Electronics product page, this compatibility allows the four control inputs to be driven by common digital logic while the analog paths operate within the device’s single- or dual-supply voltage range. Confirm input thresholds and timing in the manufacturer datasheet.
Where to buy the ISL84523IV online?
The ISL84523IV can be requested through the Request a Quote form on this XAIPART page, where the required quantity, delivery target, and packaging needs can be stated. The part is offered by authorized distribution channels, but current commercial terms should be confirmed through the quote workflow rather than relying on a static listing.
What is the lead time for the ISL84523IV?
Current lead time for the ISL84523IV should be requested through the Request a Quote form on this XAIPART page. Include the target quantity, required ship date, and whether you need tube, tape-and-reel, or another delivery format. Renesas lists support as limited for customers that have already adopted the product.
Is the ISL84523IV in stock?
The ISL84523IV is listed as in stock by distribution channels, but live inventory changes by package, region, and order quantity. Use the Request a Quote form on this XAIPART page to request the current availability and allocation for the exact quantity you need rather than relying on a fixed stock indication.
What are the key specifications of the ISL84523IV that engineers should know?
The key ISL84523IV specifications are four independently controlled SPST channels, 100 ohm maximum on-resistance, 1 ohm channel matching, less than 1 microwatt power consumption, and 1 nA maximum leakage in the principal product description. It operates from +2 V to +12 V or ±2 V to ±6 V and switches in 45 ns on and 15 ns off.

के लिए इंजीनियरिंग संदर्भ डेटा ISL84523IV — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the ISL84523IV for low-voltage, low-power designs that need four independently controlled SPST channels, a maximum on-resistance of 100 ohm, and flexible operation from +2 V to +12 V or ±2 V to ±6 V. It is particularly attractive in battery-powered test equipment, precision measurement systems, and dual-rail instrumentation where leakage below 1 microwatt and 1 nA are important. MAX4521, MAX4522, or MAX4523 are appropriate when the board was originally designed around the MAX452x drop-in family, provided the control configuration matches. DG411, DG412, or DG413 are useful for layouts already built around those pin-compatible devices, but the control truth table and electrical limits must be checked. No alternative should be approved from package appearance alone; verify channel behavior, control thresholds, timing, analog limits, and lifecycle requirements before substitution.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद MAX4521 MAX4522 MAX4523 DG411 DG412 DG413
Package 16-TSSOP 16-TSSOP 16-TSSOP 16-TSSOP 16-TSSOP 16-TSSOP 16-TSSOP
Brand Renesas Electronics Maxim Integrated Maxim Integrated Maxim Integrated Vishay Intertechnology Vishay Intertechnology Vishay Intertechnology
Maximum On-Resistance 100 ohm 100 ohm 100 ohm 100 ohm 100 ohm 100 ohm 100 ohm

मुख्य विशेषताएँ

  • Single- and dual-supply operation (बनामMAX4523)
  • Low switching power and leakage (बनामDG411)
  • Fast independent switching (बनामDG412)

डिज़ाइन नोट्स

Place the ISL84523IV close to the signal paths it switches to minimize parasitic capacitance and sensitivity to control-edge coupling. Keep the four control traces away from high-impedance analog inputs, and use a continuous ground reference beneath the device. Because the maximum on-resistance is 100 ohm, long or resistive PCB traces can contribute materially to the total path resistance.

Include the switch resistance, source impedance, receiver capacitance, and amplifier input impedance in the settling analysis. The specified 45 ns turn-on and 15 ns turn-off times describe switching behavior rather than complete analog-path settling. For precision acquisition systems, allow additional time for the RC network to settle and verify that unused channel leakage of up to 1 nA does not corrupt the measurement budget.

Do not select a replacement solely from the 16-TSSOP package. The manufacturer identifies MAX4521, MAX4522, and MAX4523 as drop-in replacements and states pin compatibility with DG411, DG412, and DG413, but the control truth table, input thresholds, switching timing, absolute maximum ratings, and intended channel configuration still must match. Confirm those details in each candidate’s datasheet before releasing a substitution.

Choose the single-supply or dual-supply configuration according to the signal range and control thresholds. The supported ranges are +2 V to +12 V and ±2 V to ±6 V. Control signals must satisfy the device’s TTL-compatible input requirements, while analog-terminal voltages must remain within the absolute maximum limits. Powering the device without checking control levels can lead to unpredictable channel states or excessive input current.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

A distributor listing states that the device is Pb-free. RoHS, REACH, halogen-free, and conflict-minerals status require confirmation from current manufacturer documentation.

डेटा सत्यापन तिथि: 2026-11-10 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

ISL84523IV datasheet ISL84523IV datasheet pdf ISL84523IV pinout Renesas ISL84523IV ISL84523IV 100 ohm switch ISL84523IV TSSOP-16 ISL84523IV quad SPST switch ISL84523IV analog switch application ISL84523IV drop-in replacement ISL84523IV vs MAX4523 ISL84523IV vs DG413 ISL84523IV equivalent ISL84523IV price ISL84523IV stock ISL84523IV lead time

संबंधित कंपोनेंट्स और शब्द

Renesas Electronics ISL84523IV ISL84523 Intersil MAX4521 MAX4522 MAX4523 DG411 DG412 DG413 analog switch SPST switch multiplexer demultiplexer interface IC CMOS TSSOP-16 surface-mount package TTL-compatible control CMOS-compatible control on-resistance leakage current break-before-make timing ESD protection battery-powered instrumentation
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें