ISL84523IV - 4-Channel SPST Analog Switch | Renesas Electronics
MPN: ISL84523IV ✗ Cuối đờiISL84523IV Tóm tắt
An analog switch is a semiconductor interface device that connects or isolates analog signals under digital control. Its function in the broader hierarchy is analog switch → multiplexer or demultiplexer → interface IC. The ISL84523IV uses four separate SPST paths rather than a shared multiplexer bus, allowing four signals to be routed independently while keeping the control logic separate from the analog nodes.
Key characteristics include a maximum on-resistance of 100 ohm, on-resistance matching between channels of 1 ohm, low power consumption below 1 microwatt, and maximum leakage current of 1 nA in the principal operating description. Switching times are listed as 45 ns on and 15 ns off. The manufacturer also identifies TTL and CMOS control compatibility, a minimum 2000 V ESD protection rating using Method 3015.7, and break-before-make timing of at least 2000 ns.
The ISL84523IV family is designed for precision low-voltage signal switching. Separate control inputs permit each SPST switch to be commanded independently, while low leakage and low power consumption help preserve small signals in battery-operated measurement equipment. Its stated pin compatibility with DG411, DG412, and DG413 devices supports reuse of existing routed analog-switch layouts when control behavior and application requirements are compatible.
Typical uses include battery-powered test equipment, automated measurement systems, signal-isolation networks, sample-and-hold circuitry, and low-voltage analog front ends. The device is also identified as a drop-in replacement for MAX4521, MAX4522, and MAX4523 devices. Because it supports both single-supply and dual-supply operation, it can address dual-rail instrumentation as well as systems whose analog signals remain above ground.
For new layouts, route each analog switch terminal to the intended signal path and keep control traces away from sensitive analog nodes. Confirm the complete pin map and control truth table in the manufacturer datasheet before making substitutions. The 16-pin TSSOP footprint supports compact density, but exposed copper and careful grounding remain important for preserving low-level signal integrity.
This page combines the manufacturer’s electrical and switching characteristics with practical routing guidance, drop-in cross-reference options, and a parameter-by-package comparison. It is intended to help engineers identify whether the ISL84523IV fits the required voltage range, control interface, switching behavior, and board footprint before requesting a quote.
Bộ thay thế dễ dàng lắp đặt cho ISL84523IV — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ISL84523IV (cùng hình factor và footprint) — khác nhau ở Package, Switch Configuration, Analog Signal Range, On-Resistance (rDS on), Power Dissipation.
MAX4521
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX4522
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX4523
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG411
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DG412
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DG413
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ISL84523IV Tỷ lệ tối đa & tính chất điện
| Number of Switches | 4 |
| Switch Configuration | 4 × SPST |
| Multiplexer Ratio | 1:1 |
| Maximum On-Resistance | 100 ohm |
| On-Resistance Matching Between Channels | 1 ohm |
| Single-Supply Voltage Range | +2 V to +12 V |
| Dual-Supply Voltage Range | ±2 V to ±6 V |
| Power Consumption | <1 microwatt |
| Maximum Leakage Current | 1 nA |
| Turn-On Time | 45 ns |
| Turn-Off Time | 15 ns |
| Break-Before-Make Timing | 2000 ns minimum |
| ESD Protection | 2000 V minimum, Method 3015.7 |
| Control Logic Compatibility | TTL and CMOS compatible |
| Hộp | 16-pin TSSOP |
| Process Technology | CMOS |
Hướng dẫn cấu hình chân ISL84523IV 16-pin tssop
Cấu hình chân cho ISL84523IV (16-pin tssop gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ISL84523IV.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ISL84523IV phù hợp cho 6 Áp dụngs: Battery-Powered Test Equipment, Automated Measurement Systems, Precision Analog Signal Isolation, Sample-and-Hold Signal Routing, Dual-Rail Instrumentation, Low-Voltage Sensor Interfacing.
Battery-Powered Test Equipment
The ISL84523IV fits low-voltage battery-powered test equipment because the manufacturer specifies power consumption below 1 microwatt and leakage current up to 1 nA. Its four independent SPST channels can isolate sensor, reference, and control paths without requiring a shared multiplexer bus. A single +2 V to +12 V supply supports portable instrumentation, while TTL-compatible control inputs allow direct interfacing with common digital controllers. The 100 ohm maximum on-resistance should be included in the input and output impedance budget when switching high-impedance sensors.
Được đề xuất
Automated Measurement Systems
The ISL84523IV is suitable for automated measurement systems that route several precision signals through a common analog front end. Four separately controlled SPST paths provide isolation between measurement channels, while 45 ns turn-on and 15 ns turn-off times support rapid sequencing. The specified 100 ohm maximum on-resistance and 1 ohm channel matching help minimize path-dependent amplitude errors. For dual-rail instruments, the ±2 V to ±6 V operating range supports bipolar signals, provided every analog and control voltage remains within the manufacturer limits.
Được đề xuất
Precision Analog Signal Isolation
The ISL84523IV can isolate precision analog nodes in instrumentation front ends where leakage and path consistency are important. The manufacturer specifies maximum leakage current of 1 nA and on-resistance matching between channels of 1 ohm, helping reduce errors introduced by unused connected paths. Four SPST channels allow a controller to connect or disconnect multiple sensitive nodes independently. Because the switch contributes up to 100 ohm on-resistance, source and receiver impedances should be considered when defining accuracy and settling requirements.
Được đề xuất
Sample-and-Hold Signal Routing
The ISL84523IV works in sample-and-hold signal-routing networks where acquisition paths must be connected quickly and isolated from inactive channels. Its 45 ns turn-on and 15 ns turn-off characteristics provide fast control response, while break-before-make timing of at least 2000 ns helps prevent overlap during state changes. The 16-pin TSSOP package allows placement close to the sampling node, reducing trace length. Designers should still account for switch on-resistance, charge injection, and settling behavior in the complete acquisition chain.
Được đề xuất
Dual-Rail Instrumentation
The ISL84523IV is appropriate for dual-rail instrumentation that must route signals around ground. Its split-supply operating range of ±2 V to ±6 V accommodates common ±5 V analog systems, while TTL and CMOS control compatibility supports conventional digital control hardware. Four independent SPST switches can route positive, negative, or reference signals without sharing a common internal bus. The analog signal amplitude and control thresholds must be checked against the datasheet for the exact supply configuration to prevent overstress during transitions.
Được đề xuất
Low-Voltage Sensor Interfacing
The ISL84523IV can route signals from low-voltage sensors where leakage and power use are critical. Its 1 nA maximum leakage specification and sub-1-microwatt power consumption help limit disturbance to high-impedance sensing circuits, while four independent channels support multiplexing between sensor, excitation, and reference paths. The maximum 100 ohm on-resistance may be significant with very high source impedances and should be included in the signal-chain error budget. Place the device near the sensor interface and keep control traces separated from sensitive analog nets.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ISL84523IV — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX4521 | MAX4522 | MAX4523 | DG411 | DG412 | DG413 |
|---|---|---|---|---|---|---|---|
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Brand | Renesas Electronics | Maxim Integrated | Maxim Integrated | Maxim Integrated | Vishay Intertechnology | Vishay Intertechnology | Vishay Intertechnology |
| Maximum On-Resistance | 100 ohm | 100 ohm | 100 ohm | 100 ohm | 100 ohm | 100 ohm | 100 ohm |
Bảo phân biệt quan trọng
- Single- and dual-supply operation (vsMAX4523)
- Low switching power and leakage (vsDG411)
- Fast independent switching (vsDG412)
Ghi chú thiết kế
Place the ISL84523IV close to the signal paths it switches to minimize parasitic capacitance and sensitivity to control-edge coupling. Keep the four control traces away from high-impedance analog inputs, and use a continuous ground reference beneath the device. Because the maximum on-resistance is 100 ohm, long or resistive PCB traces can contribute materially to the total path resistance.
Include the switch resistance, source impedance, receiver capacitance, and amplifier input impedance in the settling analysis. The specified 45 ns turn-on and 15 ns turn-off times describe switching behavior rather than complete analog-path settling. For precision acquisition systems, allow additional time for the RC network to settle and verify that unused channel leakage of up to 1 nA does not corrupt the measurement budget.
Do not select a replacement solely from the 16-TSSOP package. The manufacturer identifies MAX4521, MAX4522, and MAX4523 as drop-in replacements and states pin compatibility with DG411, DG412, and DG413, but the control truth table, input thresholds, switching timing, absolute maximum ratings, and intended channel configuration still must match. Confirm those details in each candidate’s datasheet before releasing a substitution.
Choose the single-supply or dual-supply configuration according to the signal range and control thresholds. The supported ranges are +2 V to +12 V and ±2 V to ±6 V. Control signals must satisfy the device’s TTL-compatible input requirements, while analog-terminal voltages must remain within the absolute maximum limits. Powering the device without checking control levels can lead to unpredictable channel states or excessive input current.
Thông tin tuân thủ
A distributor listing states that the device is Pb-free. RoHS, REACH, halogen-free, and conflict-minerals status require confirmation from current manufacturer documentation.